ICP DAS USA M-7026 Manual de usuario



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

1



M-7026

6-ch Analog Input, 2-ch Analog Output, 3-ch

Digital Input and 3-ch Digital Output Data

Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7026.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7026 is a Modbus RTU based multifunction module with 6 analog inputs, 2

analog outputs, 3 digital inputs, and 3 digital outputs . It provides a programmable input

range on all analog inputs (+/-150 mV, +/-500 mV, +/-1 V, +/-5 V, +/-10 V, +/-20 mA or 0

~ +20 mA). The analog outputs are 12-bit at +/-5 V, +/-10 V, 0 ~ +20 mA or +4 ~ +20

mA. All digital outputs can be set as alarm outputs. Each analog input can be

configured for an individual range and provides a high overvoltage protection of 240

Vrms. Voltage and current inputs/outputs are jumper selectable.

2. Terminal Assignment



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2



3. Block/ Wiring Diagram



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3



4. Default Settings

The default settings for the M-7026 are:

・ Module Address: 01

・ Analog Input Type: Type 08, -10 V to +10 V

・ Analog Output Type: Type 3, -10 V to +10 V

・ Protocol: Modbus RTU

・ Baud Rate: 9600 bps

・ Checksum disabled

・ Engineering Units format

・ Filter set at 60 Hz rejection



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5



5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

6



4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7



5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8



7. For M-7000 modules using the Modbus RTU protocol, configure the module using the

following functions.

・ Sub-function 04h of Function 46h, see user manual Section 3.3.2

・ Sub-function 06h of Function 46h, see user manual Section 3.3.4

・ Sub-function 08h of Function 46h, see user manual Section 3.3.6

For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the

data from the input channels. See user manual Section 3.2 for details.



M‐70266‐chAI,2‐chAO,3‐chDIand3‐chDODAQModule‐QuickStart(Mar/2019)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

9



8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.



Otros manuales para M-7026

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA GTM-204M-4G Manual de usuario

ICP DAS USA

ICP DAS USA iDaSer-9000 Manual de usuario

ICP DAS USA

ICP DAS USA I-2533 Manual de usuario

ICP DAS USA

ICP DAS USA LP-8 4 Series Instrucciones generales

ICP DAS USA

ICP DAS USA I-8014W Manual de usuario

ICP DAS USA

ICP DAS USA FR-32R Manual de usuario

ICP DAS USA

ICP DAS USA I-7016D Manual de usuario

ICP DAS USA

ICP DAS USA tSH-734 Manual de usuario

ICP DAS USA

ICP DAS USA ET-7H16M Series Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2026 Manual de usuario

ICP DAS USA

ICP DAS USA M-7041D Manual de usuario

ICP DAS USA

ICP DAS USA M-7019Z Manual de usuario

ICP DAS USA

ICP DAS USA M-7024 Manual de usuario

ICP DAS USA

ICP DAS USA M-7069 Manual de usuario

ICP DAS USA

ICP DAS USA tSH-735 Manual de usuario

ICP DAS USA

ICP DAS USA DS-700 Series Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2061 Manual de usuario

ICP DAS USA

ICP DAS USA I-7045D Manual de usuario

ICP DAS USA

ICP DAS USA Zigbee ZT-2060 Manual de usuario

ICP DAS USA

ICP DAS USA I-7041 Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2000 Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7067D Manual de usuario

ICP DAS USA

ICP DAS USA I-7014D Manual de usuario

ICP DAS USA

ICP DAS USA M-7033D Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario