ICP DAS USA M-7019Z Manual de usuario

M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7019Z

10-channel Universal Voltage Input & Current

Input, thermocouple input Module

Quick Start Guide

Product Website:

http://www.icpdas-usa.com/m_7019z.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

M-7019Z is an RS-485 interface and 10-channel thermocouple input module. The

analog input range is software selectable and supports +/-15 mV, +/-100 mV, +/-150mV,

+/-500 mV, +/-1 V, +/-2.5 V, +/-5 V, +/-V10, +/-20 mA, 0 ~ 20 mA, and thermocouple of

type J, K, T, E, R, S, B, N, C, L, M, and LDIM43710. I-87019ZW uses external terminal

design, and takes thermocouple temperature output consistency.

2. Terminal Assignment

M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7019Z Jumper Settings

The M-7019Z can accept current inputs from –20mA to 20mA. No external resistor

required but the corresponding jumper must be shorted. The following figure shows the

jumper positions.

4. Default Settings

Default settings for the M-7017, M-7018 and M-7019 series modules are:

▫Protocol: Modbus RTU

▫Module address: 01

▫Analog input type:

Type 08, -10V to 10V, for the M-7017 and M-7019 series

Type 1B, -150V to 150V, for the M-7017R-A5

Type 0D, -20mA to +20mA for the M-7017C and M-7017RC

Type 05, -2.5V to 2.5V, for the M-7018 series

▫Baud Rate: 9600 bps

▫Filter set at 60Hz rejection (Not used by the M-7019R, firmware version B2.6 and

earlier)

M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For M-7000 modules using the Modbus RTU protocol, configure the module using the

following functions.

Sub-function 04h of Function 46h, see user manual Section 3.3.2

Sub-function 06h of Function 46h, see user manual Section 3.3.4

Sub-function 08h of Function 46h, see user manual Section 3.3.6

For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the

data from the input channels. See user manual Section 3.2 for details.

M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Tabla de contenidos

Otros manuales de Unidad de control de ICP DAS USA

ICP DAS USA

ICP DAS USA tM-AD8C Manual de usuario

ICP DAS USA

ICP DAS USA WF-2051 Manual de usuario

ICP DAS USA

ICP DAS USA PM-3033 Series Manual de usuario

ICP DAS USA

ICP DAS USA ECAT-2061 Manual de usuario

ICP DAS USA

ICP DAS USA EIP-2000 Series Guía de instalación

ICP DAS USA

ICP DAS USA GW-7552-M Manual de usuario

ICP DAS USA

ICP DAS USA tM-TH8 Manual de usuario

ICP DAS USA

ICP DAS USA PET-AR400 Manual de usuario

ICP DAS USA

ICP DAS USA I-7016 Manual de usuario

ICP DAS USA

ICP DAS USA ZT-2055 Manual de usuario

ICP DAS USA

ICP DAS USA I-8026W Manual de usuario

ICP DAS USA

ICP DAS USA M-7067D Manual de usuario

ICP DAS USA

ICP DAS USA ET-6000 Series Manual de usuario

ICP DAS USA

ICP DAS USA M-7064 Manual de usuario

ICP DAS USA

ICP DAS USA tET-P2A2 Manual de usuario

ICP DAS USA

ICP DAS USA I-7045D Manual de usuario

ICP DAS USA

ICP DAS USA LinPAC-51 Series Manual de usuario

ICP DAS USA

ICP DAS USA LP-8 4 Series Instrucciones generales

ICP DAS USA

ICP DAS USA M-7053D Manual de usuario

ICP DAS USA

ICP DAS USA ET-7015 Manual de usuario

ICP DAS USA

ICP DAS USA I-7063 Manual de usuario

ICP DAS USA

ICP DAS USA I-7088 Manual de usuario

ICP DAS USA

ICP DAS USA FR-32R Manual de usuario

ICP DAS USA

ICP DAS USA SP-S2-DS Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario