Geeetech PrusaI3 pro C Manual de usuario

Geeetech prusaI3 pro C

User Manual

Safety Instructions

Building the printer will require a certain amount of physical dexterity, common sense and a

thorough understanding of what you are doing. We have provided this detailed instruction to help

you assemble it easily.

However ultimately we cannot be responsible for your health and safety whilst building or

operating the printer, with that in mind be sure you are confident with what you are doing prior to

commencing with building or buying. Read the entire manual to enable you to make an informed

decision.

Building and operating involves electricity, so all necessary precautions should be taken and

adhered to, the printer runs on 12V supplied by a certified power supply, so you shouldn’t ever have

to get involved with anything over 12V but bear in mind there can still be high currents involved

and even at 12V they shouldn’t be taken lightly.

Check the power input of the power supply unit. You can choose either 110V or 220V according to

the Power regulation in your country.

High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end can run about

230°C, the heated bed runs 110°C and the molten plastic extruded will initially be at around 200°C,

so special care and attention should be made when handling these parts of the printer during

operation.

We wouldn’t recommend leaving your printer running unattended, or at least until you are confident

to do so. We cannot be held responsible for any loss, damage, threat, hurt or other negligent result

from either building or using the printer.

www.geeetech.com

ShenZhen GETECH CO.,LTD

1Software Resources

1.1 Repetier-Host

We use the latest Repetier host 1.6.0 as the printer control software, here is the link for download:

http://www.geeetech.com/wiki/index.php/Repetier-Host#Download

After downloading and installation, it can be used.

1.2 Driver

Connect the printer to computer with USB cable, the motherboard driver installer will automatically

appear. If not, you can download FT232RQ here, which is the driver of GT2560:

http://www.geeetech.com/wiki/index.php/Prusa_I3_X#Install_the_drivers

www.geeetech.com

ShenZhen GETECH CO.,LTD

Download and install, you can find the corresponding serial port in the Windows "Device

Manager":

1.3 Arduino IDE

In the process of using the printer you may need to re-upload the firmware, and the software you

need to use is Arduino. About how to upload firmware please refer to FAQ.

2Connect the Printer

After the above software is installed, we can connect the printer to the computer. Plug the USB into

the computer, open Repetier host, click the icon in the top right corner, and the dialog

box of printer settings will appear.

www.geeetech.com

ShenZhen GETECH CO.,LTD

Select corresponding COM port of the printer and baud rate as 250,000 in the drop-down menu.

Click Apply after the setting. Shown as below.

www.geeetech.com

ShenZhen GETECH CO.,LTD

After setting, click the button in the top left corner of Home Page. When the button turns

green and changes into , the printer connection is successful.

www.geeetech.com

ShenZhen GETECH CO.,LTD

3Printer Setting

3.1 Printer Speed

Set the running speed of printer as 1000 in the printer settings in order to avoid collision because of

high speed during the test. After follow-up tests are completed it can be changed back to the original

value. (Recommend speed of Z-axis should not be too high, 1000 is OK)

Travel feed rate: 1000mm/min

Z-Axis feed rate: 1000mm/min

www.geeetech.com

ShenZhen GETECH CO.,LTD

3.2 Number of Extruder and Nozzle Diameter

The number of extruder is set as 1. The diameter of print head is set according to the actual size,

here is 0.4mm.

The distance between two extruders on X direction is 32mm, then set offset X -16 and 16mm. (You

can also set it depending on actual measurement)

www.geeetech.com

ShenZhen GETECH CO.,LTD

www.geeetech.com

ShenZhen GETECH CO.,LTD

3.3 Printer Shape

Here the printer shape of I3 pro C is Classic Printer;

For home position, choose Min;

The printer's maximum printing volume 200 * 200 * 180 (length / width / height)

Tabla de contenidos

Otros manuales de Impresora 3D de Geeetech

Geeetech

Geeetech I3 Pro C Manual de usuario

Geeetech

Geeetech A10 Manual de usuario

Geeetech

Geeetech Prusa I3 A pro Manual de usuario

Geeetech

Geeetech Acrylic I3 Pro Manual de usuario

Geeetech

Geeetech Duplicator 5 Manual de usuario

Geeetech

Geeetech E180 Manual de usuario

Geeetech

Geeetech A30T Manual de usuario

Geeetech

Geeetech Me Creator Manual de usuario

Geeetech

Geeetech Mizar S Manual de usuario

Geeetech

Geeetech acrylic Prusa I3 Manual de usuario

Geeetech

Geeetech Prusa I3 M201 Manual de usuario

Geeetech

Geeetech Acrylic I3 Pro Manual de usuario

Geeetech

Geeetech GCW01 Manual de usuario

Geeetech

Geeetech acrylic Prusa I3 Instrucciones de operación

Geeetech

Geeetech Delta Rostock mini G2 pro Manual de usuario

Geeetech

Geeetech E180 Manual de usuario

Geeetech

Geeetech Delta Rostock mini G2S Pro Manual de usuario

Geeetech

Geeetech GiantArm D200 Manual de usuario

Geeetech

Geeetech Acrylic I3 Pro Manual de usuario

Geeetech

Geeetech Prusa I3 X Manual de instrucciones

Geeetech

Geeetech Delta Rostock mini G2 pro Manual de instrucciones

Geeetech

Geeetech A30 Manual de usuario

Geeetech

Geeetech Delta Rostock mini G2 Manual de usuario

Geeetech

Geeetech Delta Rostock mini G2 Manual del operador

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

Geeetech prusaI3 pro C Manual de usuario

Manuales populares de Impresora 3D de otras marcas