Geeetech A30 Manual de instrucciones
Geeetech A30 3D Printer
—Building Instruction—
Contents
Safety Instructions ..........................................................................................................................................1
Preparation......................................................................................................................................................2
1. Unfold the Box and Check the Package..................................................................................................3
2. Assembly ................................................................................................................................................4
3. Wiring.....................................................................................................................................................9
4. Warm Tips.............................................................................................................................................16
1
Safety Instructions
Building the printer will require a certain amount of physical dexterity, common sense
and a thorough understanding of what you are doing. We have provided this detailed
instruction to help you assemble it easily.
However, ultimately we cannot be responsible for your health and safety while you are
building or operating the printer. Therefore, be sure you are confident in what you are doing
prior to commencing with building or buying. Read the entire manual to enable you to make
an informed decision.
Building and operating involves electricity and all necessary precautions should be taken
and adhered to. Check the power input of the power supply unit. You can choose either 110V
or 220V according to the power regulation in your country.
High temperatures are involved in 3D Printing. The extrusion nozzle of the hot end can
run at about 210°C, the heated bed runs at 110°C and the molten plastic extruded will initially
be at around 200°C. Therefore, special care and attention should be taken when you are
handling these parts of the printer during operation.
We wouldn’t suggest you to leave your printer running unattended, or at least until you
are confident to do so. We are not responsible for any loss, damage, threat, hurt or other
negligent result caused by either building or using the printer.
2
Preparation
1. Unpack the kit and check if all parts are in the box. Please check the condition of each part
since there might be some damage during shipping. To help you with this, there is BOM in
the box and each bag is labeled with its part number.
2. Contact our customer service immediately by email or through the website if you find any
missing or damaged parts. And at the bottom of the BOM, there is a signature of the checker.
Please take a picture of it and attach the picture in your mail.
3. Before your assembly, please read through each chapter of this assembly
manual to gain an overall idea of what is involved and how long it might
take to complete the assembly job.
4. As a preparation job, you can put all the part in order to save your time, especially the
screws and nuts. Do not mix them up.
5. Ensure you have the necessary skills to carry out the assembly job or entrust someone who
does.
6. Work on a big firm table or bench in a clean dry well-lit area.
7. Since this kit contains tiny parts, please keep them away from kids under 3.
8. Ask for help if you run into any problems --- our contact details are on the website and we
will always do our best to solve any problems encountered.
9. For different batches, some parts of the kits may have changed. If the parts listed in
this instruction and what you received is slightly different, please don't worry. These
changes will not affect your installation and usage.
10. Please watch the building instruction video at https://youtu.be/hM_ZYANWnGw
3
1. Unfold the Box and Check the Package
Step1. Unfold the package and take all the parts out to check the condition of the items.
As you can see, all the parts are packed very carefully.
Step 2. Check the materials.
Materials in the Foam box
4
Bottom frame parts, Vertical frame parts, Control box
Materials in the Tool Box
4* M5x20mm hex screws, 4 spring washers, Filament spool, 2* M3x6mm screws, Power
cable, Blue A-B USB cord, 2* Z axis stator kits, 3D touch stator, Filament detector kit,
Ties, Allen key, Pin, Starter filament, Spare screw package, TF card
Tips:
1. Before assembly, you are advised to put all the parts, especially the screws and nuts in
order, which would save you much time in looking for the required parts.
2. The part ID is corresponding to the number labeled on the bag of each part. Some
parts may not have labels and you can refer to the pictures on the package list.
2. Assembly
Step 1. Prepare the following parts for assembling:
Bottom frame parts, vertical frame parts, 4* M5x20mm hex screws and 4 spring
washers, 2*Z axis stators
Step 2. Place the vertical frame parts on the bottom frame one (Note: Just keep the
ends of the blue strips on the two frames meet each other.)
5
Step 3. Use 4* M5x20mm hex screws and 4 spring washers to put the bottom frame
parts and the vertical frame parts together.
6
Step 4. Fix the two Z axis stators on two sides of the vertical frame respectively.
Fasten the screws on the stators in a relatively loose way.
Note: Pay attention to the direction of the nuts on the Z axis stator.
7
Right
8
Left
Otros manuales para A30
3
Tabla de contenidos
Otros manuales de Impresora 3D de Geeetech
Geeetech
Geeetech A20T Manual de usuario
Geeetech
Geeetech GCW01 Manual de usuario
Geeetech
Geeetech Delta Rostock mini G2 pro Manual de usuario
Geeetech
Geeetech Acrylic I3 Pro Manual de usuario
Geeetech
Geeetech Delta Rostock mini G2 Manual de instrucciones
Geeetech
Geeetech Prusa M201 Manual del operador
Geeetech
Geeetech Delta Rostock mini G2 Manual del operador
Geeetech
Geeetech ME CREATOR 2 Manual de usuario
Geeetech
Geeetech A30 Manual de usuario
Geeetech
Geeetech Prusa I3 M201 Manual de usuario
Geeetech
Geeetech acrylic Prusa I3 Instrucciones de operación
Geeetech
Geeetech acrylic Prusa I3 Manual de usuario
Geeetech
Geeetech Delta Rostock mini G2 Manual de usuario
Geeetech
Geeetech A10 Manual de usuario
Geeetech
Geeetech I3 Pro C Manual de usuario
Geeetech
Geeetech Acrylic I3 Pro Manual de usuario
Geeetech
Geeetech Acrylic I3 Pro Instrucciones de operación
Geeetech
Geeetech A10T Manual de usuario
Geeetech
Geeetech GiantArm D200 Manual de usuario
Geeetech
Geeetech Acrylic I3 Pro Manual de usuario
