AnyCubic Kossel Plus Manual de usuario

Tabla de contenidos

Otros manuales de Impresora 3D de AnyCubic

AnyCubic

AnyCubic i3 MEGA Manual de usuario

AnyCubic

AnyCubic Prusa i3 Manual de usuario

AnyCubic

AnyCubic Kobra Go Manual de usuario

AnyCubic

AnyCubic Photon Mono Manual de usuario

AnyCubic

AnyCubic Wash and Cure Manual de usuario

AnyCubic

AnyCubic VYPER Manual de usuario

AnyCubic

AnyCubic i3 MEGA Manual de usuario

AnyCubic

AnyCubic Kobra Manual de usuario

AnyCubic

AnyCubic Kobra Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

LONGER

LONGER LK4 Pro Manual de usuario

Modification for Anycubic Kossel Plus 3D Printer

To print large size object (such as φ230×200), the printer needs modifications.

1. Assembling

As page 4 in the manual, add copper spacers(C19, new part)between effector

and CFT-JBs, as the following figure shows, and fix them with HSHCS M3×20 (C02).

As page 5 in the manual, add copper spacers (C19) between belt tensioners

and CFT-JBs, as the following figure shows, and fix them with HSHCS M3×25 (C20,

new part)instead of HSHCS M3×20 (C02).

Please make sure C19 are in right directions.

C02

C19

C19

C20

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

Assemble the linear rails (D06) as the following figures show.

2. Firmware

Change the parameters in firmware as the following figure shows or download the

latest firmware from Google Drive

(https://drive.google.com/open?id=0B8VIB533cgdMSVMxNm43aG1OQ0U).

DELTA_DIAGONAL_ROD change 267 to 271.5 or the number you debug (Page

19 in the manual);

DELTA_SMOOTH_ROD_OFFSET change 188 to 187 or the number you debug;

DELTA_PRINTABLE_RADIUS change 115 to 116；

For the limit switches have been moved down, the height need to be adjusted

(Page 18), and you also need level the platform.

Less

than

67mm

Less

than

15mm

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

3. Cura

Change the width and depth to a number bigger than 230 such as 240

Change the start distance to 0.5 (3 for default) in expert config.

To print small parts, it is suggested to change the start distance back to 3.

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC

ANYCUBIC ANYCUBIC ANYCUBIC