Geeetech Acrylic Prusa I3 Manual de usuario

Assemble Instruction of Geeetech Acrylic Prusa I3

pro B

Version 04-11-2016

Shenzhen GETECH CO.,LTD

GEEETECH

Safety Instructions

Building the printer will require a certain amount of physical dexterity, common sense

and a thorough understanding of what you are doing. We have provided this detailed

instruction to help you assemble it easily.

However ultimately we cannot be responsible for your health and safety whilst

building or operating the printer, with that in mind be sure you are confident with

what you are doing prior to commencing with building or buying. Read the entire

manual to enable you to make an informed decision.

Building and operating involves electricity, so all necessary precautions should be

taken and adhered to, the printer runs on 12V supplied by a certified power supply, so

you shouldn’t ever have to get involved with anything over 12V but bear in mind

there can still be high currents involved and even at 12V they shouldn’t be taken

lightly.

High temperatures are involved with 3D Printing, the Extrusion nozzle of the hot end

can run about 230°C, the heated bed runs 110°C and the molten plastic extruded will

initially be at around 200°C, so special care and attention should be made when

handling these parts of the printer during operation.

We wouldn’t recommend leaving your printer running unattended, or at least until you

are confident to do so. We cannot be held responsible for any loss, damage, threat,

hurt or other negligent result from either building or using the printer.

Shenzhen GETECH CO.,LTD

GEEETECH

Preparation

1. Unpack the kit and check if all parts are in the box and check the condition of each

part, there might be some damage during shipping. To help you with this, there is

BOM in the box and each bag was labeled with part number.

2. Contact our customer service immediately by email or through the website if you

find any missing or damaged parts. And on the bottom of the BOM, there is a

signature of reviewer, please take a picture of it and attach the picture in your mail.

3. Read through each chapter of these instructions to gain an over-all idea of what is

involved and how long it might take, before starting on the work described.

4. Before you start, you can put all the part in order to save your time especially those

screws and nuts. Do not mix them up.

5. Ensure you have the necessary skills to carry out the work, or enlist the help of

someone who does.

6. Work on a big firm table or bench in a clean dry well-lit area.

7. This kit contains tiny parts; please keep them away from kids under 3.

8. Ask for help if you run into any problems - our contact details are on the website

and we will always do our best to resolve any problems encountered.

Shenzhen GETECH CO.,LTD

GEEETECH

1Unfold the box and check the package

Unfold the package and take all the parts out to check the condition of the items. As

you can see, all the parts are packed very carefully.

Shenzhen GETECH CO.,LTD

GEEETECH

All the acrylic plate has been etched with part ID and the plate is covered with

a sheet of Kraft paper, you need to tear them off.

Shenzhen GETECH CO.,LTD

GEEETECH

Tips:

1. Before assembly, you are advised to put all the parts, especially the screws and nuts

in order, which will save you a lot of time looking for the required parts.

2. The part ID is corresponding to the number labeled on the bag of every part. Some

parts may not have label, you can refer to the pictures on the package list.

2 Assemble the rods of a Y axis

Watch the video

Step1.Assemble the 2 threaded rods.

Pic

Part ID

Required number

Required parts

NO.5

M10 threaded rod

NO.A14

Y plate connecting

plate

NO.19

M10 spring washer

NO.9

M10 washer

NO.13

M10 nut

Thread the nuts and washers into the two M10 threaded rods separately. The order

should be:

1) Thread the Y plate connecting plate A14 in the middle.

2) Thread the M10 washer > M8 spring washer >M10 nut > M10 nut > M10 washer

Shenzhen GETECH CO.,LTD

GEEETECH

on the left

3) Thread theM10 washer < M8 spring washer < M10 nut < M10 nut< M8 spring

washer < M10 washer on the right

4) repeat the above steps for another threaded rod.

Shenzhen GETECH CO.,LTD

GEEETECH

Step2.Assemble the 2 smooth rods

Pic

Part ID

Required number

Required parts

NO.3

M8 smooth rod

NO.36

LM8UU Linear

bearings

Take out the 410mm smooth rod

Slide 2 Linear bearings on each smooth rod. Before you slide the bearings please

make sure they are clean.

Shenzhen GETECH CO.,LTD

GEEETECH

3 Attach the front and rear support plates

Watch the video

For some of the kit, the locking rings are the silver color, which will not affect the

assembly here, but in some steps, for the X axis, there is difference, please pay

attention to the note.

Shenzhen GETECH CO.,LTD

GEEETECH

Step1.Slide the locking ring on the smooth rods, thread the rods into the acrylic plate;

adjust the length so that the smooth rods fit snugly between the front and rear piece.

Step2. Screw up the rods and plate with M10 nut and M10 washer.

Pic

Part ID

Required number

Required parts

NO. A9,

A 10

Acrylic

plate( front)

NO. A 11, A

Acrylic

plate( rear)

NO.9

M10 washer

NO.13

M10 nut

NO.20

locking ring

Otros manuales para acrylic Prusa I3

Tabla de contenidos

Otros manuales de Impresora 3D de Geeetech

Geeetech

Geeetech A10M Manual de usuario

Geeetech

Geeetech Acrylic I3 Pro Manual de usuario

Geeetech

Geeetech A10 Manual de usuario

Geeetech

Geeetech A20M Manual de usuario

Geeetech

Geeetech Acrylic I3 Pro Manual de usuario

Geeetech

Geeetech A30 Manual de instrucciones

Geeetech

Geeetech E180 Manual de usuario

Geeetech

Geeetech A10 Manual de usuario

Geeetech

Geeetech Mizar S Manual de usuario

Geeetech

Geeetech prusaI3 pro C Manual de usuario

Geeetech

Geeetech Aluminum Prusa I3 Manual de usuario

Geeetech

Geeetech Duplicator 5 Manual de usuario

Geeetech

Geeetech Delta Rostock mini G2 pro Manual de instrucciones

Geeetech

Geeetech Acrylic I3 Pro Instrucciones de operación

Geeetech

Geeetech Acrylic I3 Pro Manual de usuario

Geeetech

Geeetech Prusa I3 X Manual de instrucciones

Geeetech

Geeetech I3 Pro C Manual de usuario

Geeetech

Geeetech Delta Rostock mini G2 Manual de usuario

Geeetech

Geeetech A30T Manual de usuario

Geeetech

Geeetech Delta Rostock mini G2 pro Manual de usuario

Geeetech

Geeetech Delta Rostock mini G2 Manual del operador

Geeetech

Geeetech Duplicator 5 Manual de usuario

Geeetech

Geeetech A20T Manual de usuario

Geeetech

Geeetech Delta Rostock mini G2 Manual de instrucciones

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

Geeetech acrylic Prusa I3 Manual de usuario

Manuales populares de Impresora 3D de otras marcas