CYP PU-2H8HBTE-AD Manual de usuario

PU-2H8HBTE-AD

2 x 8 HDBaseT™ Switch with Audio Dembedding

OPERATION MANUAL

DISCLAIMERS

The information in this manual has been carefully checked and is

believed to be accurate. CYP (UK) Ltd assumes no responsibility for any

infringements of patents or other rights of third parties which may result

from its use.

CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be

contained in this document. CYP (UK) Ltd also makes no commitment to

update or to keep current the information contained in this document.

CYP (UK) Ltd reserves the right to make improvements to this document

and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed,

stored in a retrieval system, or any of its part translated into any language

or computer le, in any form or by any means—electronic, mechanical,

magnetic, optical, chemical, manual, or otherwise—without express

written permission and consent from CYP (UK) Ltd.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate

this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside

the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if

it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sucient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

v1.00 25/04/2014 First release

CONTENTS

1. Introduction...........................................6

2. Applications ...........................................6

3. Package Contents ..................................6

4. System Requirements ...........................7

5. Features..................................................7

6. Operation Controls and Functions .......8

6.1 Front Panel................................................... 8

6.2 Rear Panel..................................................... 8

6.3 IR Cable Pin Assignment.......................10

6.4 Remote Control........................................10

6.5 RS-232 Pin Denition .............................11

6.6 RS-232 Commands..................................11

7. Connection Diagram .......................... 12

8. Specications...................................... 13

8.1 Technical Specications ........................13

8.2 CAT5e/6/7 Cable Specication ...........14

9. Acronyms............................................. 14

1. INTRODUCTION

The PU-2H8HBTE HDBaseT switch has two HDMI inputs and eight

HDBaseT outputs, plus a single HDMI output. This device allows the user

to select either HDMI source for distribution to all screens simultaneously.

Each HDBaseT output supports the transmission of video (resolutions up

to 1080p Full HD, plus 4K Ultra High Denition, and 1920x1200@60Hz),

multi-channel audio, single LAN serving, and control via 2-way IR, RS-

232 or Web GUI/Telnet IP over a single CAT5e/6/7 cable (up to 100m). The

HDMI output supports the same video resolutions and high denition

audio via certied HDMI cables up to 15m.

For additional exibility, the PU-2H4HBTE is provided with Audio De-

Embedding functionality allowing easy audio integration into a wider

AV system or direct connection to an AVR. Audio outputs are via a single

Optical connection or an Analogue Stereo output (2×RCA).

The HDBaseT outputs are designed to be used with any compatible

HDBaseT Receiver as follows: PU-507RX / PU-507RX-2H / PU-507RX-SCD /

PU-507WPRX / PU-1109RX. These Receivers support Power over Ethernet

(PoE) function so do not require a separate PSU for power.

Use the LAN serving capabilities of this switch to add internet connectivity

to every HDBaseT output zone. In addition, this switch also features IP

control allowing users to access and control the matrix remotely and also

allow additional options for integration of third-party control systems

such as Control 4.

2. APPLICATIONS

Household entertainment sharing and control

Lecture room display and control

Showroom display and control

3. PACKAGE CONTENTS

HDMI over HDMI & CAT5e/6/7 with PoE and Ethernet Transmitter

1× IR Receiver

1× IR Blaster

1× Remote Control

24V DC Power Adaptor

Power Cord

Operation Manual

4. SYSTEM REQUIREMENTS

Source equipment with HDMI output connector

Display TV/Monitor with HDMI input connector

HDMI over CAT5e/6/7 Receivers with industry CAT5e/6/7 cables

5. FEATURES

HDMI, HDCP and DVI complaint

Common supported resolutions: HDTV: 480p, 576p, 720p, 1080i,

1080p, 1080p24, 4K; PC: VGA, SVGA, XGA, WXGA, SXGA, UXGA, WUXGA,

1920x1200@60Hz

High Denition Audio supported: Dolby TrueHD, Dolby Digital Plus

and DTS-HD Master Audio plus LPCM (up to 192kHz)

Uncompressed data transfer over single CAT cable for HDBaseT

outputs (100m - CAT6/7; 80m - CAT5e)

Supports HDMI input up to 15m 1080p 8bit or 10m 1080p 12bit.

Supports RS-232, 2-Way IR, Manual Selection Buttons, and Web GUI/

Telnet IP for control

HDBaseT outputs support Power over Ethernet (PoE) with compatible

receiver units

Supports LAN serving to all connected HDBaseT zones

Supports 3D signals and 4K Ultra High Denition

Note:

1. This system was tested with CAT6/23AWG cables, results may vary with

cables of a dierent specication.

2. The PoE function is designed for powering compatible Receiver units only

non-PoE Receivers will need their own power supply. Receivers of another

brand may not be compatible.

3. Displaying HDMI 4Kx2K resolution require the standard 4Kx2K HDMI cable

and display in order for proper image displaying.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER SYNC HDMI

IN 1

HDMI

IN 2 HDMI

LINK

LINK 1LINK 2LINK 3LINK 4LINK 5LINK 6LINK 7LINK 8

CAT5e/6/7 OUT

1 2 3 4 5

1IR Window: Receive IR signal from the package included remote

control only.

2POWER Button & LED: Press this button to switch ON or set the

device to standby mode and the LED will illuminate in Green and Red.

3SYNC: This LED will illuminate when the HDMI input port connected

to the source.

4HDMI IN 1/2: Press the button to selection HDMI input source 1 or 2.

The LED will illuminate according to the selection.

5HDMI & CAT OUT LINK 1~8: These link LEDs will illuminate when

HDMI or CAT5e/6/7 output(s) has been connected to the Display/

Receiver(s) and the Receiver(s) has connected with display that shows

image on screen.

6.2 Rear Panel

87654321LAN OPTICAL

OUT

HDMI

OUT

HDMI

IN 2

HDMI

IN 1

RS-232

IR OUTL/R OUT

IR IN

SERVICE

STDTV

DC 24VDC 24V

EDID

CAT5e/6/7 OUT

1 3

2 11

54 6 7 8 9 10 12

1CAT5e/6/7 OUT 1~8: Connect these ports to CAT5e/6/7 to HDMI

Receivers (with or without PoE function) with CAT5e/6/7 cable to

extend the signal up to 100m.

2IR OUT: Connect with IR Blaster to blast out the IR signal received

from the Receiver side. Place the IR Blaster in direct line-of-sight of the

equipment to be controlled.

3IR IN: Connect with IR Extender to receive IR signal from Transmitter

side and blast out at Receiver side. Ensure that remote controller

being used is within the direct line-of-sight of the IR Extender.

4LAN: Connect to intranet or internet service system for a total sharing

rate of 100Mbps within the link of Transmitter.

Warning: DO NOT connect this slot with any of the CAT5e/6/7 port, doing

so may trigger a power shot down and ruin the device.

5L/R OUT: Connect to active speaker or audio equipment for audio

signal output.

6OPTICAL OUT: Connect to active speaker or audio equipment for

audio signal output.

7HDMI OUT: Connect to HDMI display for instant image display or

cascade with another family type Transmitter.

8HDMI IN1/2: Connect with source equipment such as DVD/Blu-ray or

PS3 player.

9EDID STD/TV: The default factory setting is on TV, leave as it is when

the display is properly. The unit will detect rst the HDMI output’s

EDID and send out the signal accordingly to other output ports. If

the HDMI output port is not connected the device will detect the 1st

CAT5e/6/7 output's EDID and send out the signal accordingly to all

outputs.

This device obtain the last memory function therefore, the device will

use the last HMDI output port/the 1st CAT5e/6/7's output EDID after

power cycling or switch in between the EDID setting.

Switch to STD to use build-in EDID if the display has problem. STD

EDID's video at 1080p@60Hz and audio at LPCM 2CH.

10 SERVICE: This slot is reserved for factory service only.

11 RS-232: Connect this slot from PC/Laptop for RS-232 command

sending.

12 DC 24V: Plug the 24V DC power supply into the unit and connect the

adaptor to an AC outlet.

6.3 IR Cable Pin Assignment

1Power 3.3V

IR Blaster Signal

IR Signal

Power 3.3V

Ground

IR Extender

IR Blaster

6.4 Remote Control

1Power: Press the button to turn

On/O the unit.

2Input Selection 1/2: Press 1/2 to

select HDMI input sources 1 or 2.

CR-37

POWER

Tabla de contenidos

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario