CYP EL-7500V Manual de usuario

EL-7500V

HDM/VGA/YUV/CV to HDMI/VGA & HDBaseT (48V)

Presentation Switch

OPERATION MANUAL

DISCLAIMERS

The information in this manual has been carefully checked and is

believed to be accurate. CYP (UK) Ltd assumes no responsibility for any

infringements of patents or other rights of third parties which may result

from its use.

CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be

contained in this document. CYP (UK) Ltd also makes no commitment to

update or to keep current the information contained in this document.

CYP (UK) Ltd reserves the right to make improvements to this document

and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed,

stored in a retrieval system, or any of its part translated into any language

or computer file, in any form or by any means—electronic, mechanical,

magnetic, optical, chemical, manual, or otherwise—without express

written permission and consent from CYP (UK) Ltd.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate

this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of fire,

electrical shock and injury to persons.

• To prevent fire or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside

the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if

it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufficient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

v1.00 23/04/2018 First release

CONTENTS

1. Introduction...........................................6

2. Applications ...........................................6

3. Package Contents ..................................6

4. System Requirements ...........................7

5. Features..................................................7

6. Operation Controls and Functions.......8

6.1 Front Panel................................................... 8

6.2 Rear Panel..................................................... 9

6.3 Remote Control........................................11

6.4 IR Cable Pinouts .......................................11

6.5 OSD Menu ..................................................12

6.6 WebGUI Control .......................................19

6.7 RS-232 Control..........................................23

6.8 Telnet Control............................................23

6.9 RS-232 and Telnet Commands............24

7. Connection Diagram .......................... 34

8. Specifications...................................... 35

8.1 Technical Specifications ........................35

8.2 Video Specifications................................37

8.3 Audio Specifications...............................38

9. Acronyms............................................. 39

1. INTRODUCTION

This multi-input scaler has HDMI, as well as Composite Video, Component

Video, and PC (VGA) inputs which can be freely selected for output at a

scaled resolution of the user’s choosing over the mirrored HDMI, HDBaseT

and VGA outputs. This unit also includes analogue and digital audio out-

puts to provide additional playback exibility. Support for HDMI output

resolutions up to 1080p/WUXGA (RB) and Analogue to Digital Conversion

(ADC) functionality combine to allow for a wide range of AV signals to be

displayed on the connected displays.

The HDBaseT output provides a great solution to extend your audio and

video up to 70 metres over a single run of Cat.5e/6/7 cable. The HDBaseT

output can provide 48V PoH power to compatible HDBaseT Receivers. The

unit can be controlled via front panel buttons with an On-Screen Display

(OSD), WebGUI, IR remote, Telnet, and RS-232 making it exceptionally ver-

satile.

2. APPLICATIONS

Analogue and digital source integration

Upscaling standard denition video for high-denition displays

Conference centers

Lecture halls

Schools and universities

3. PACKAGE CONTENTS

1×Multi-format to HDMI/HDBaseT Scaler

1×24V/2.7A DC Power Adapter

1×Power Cord

1×15-pin D-sub to 3-RCA Cable

1×3.5mm to IR Extender Cable

1×Remote Control (CR-122)

1×Rackmount Ears (Set of 2)

1×Operation Manual

4. SYSTEM REQUIREMENTS

HDMI, VGA, component or composite video source equipment such as

media players, video game consoles, PCs, or set-top boxes.

HDMI or VGA receiving equipment such as HDTVs, monitors or audio

ampliers.

A compatible HDBaseT receiver with 48v PoH support is strongly

recommended.

The use of “Premium High Speed HDMI”cables is highly recommended.

The use of industry standard Cat.6, Cat.6a or Cat.7 cable is highly

recommended.

5. FEATURES

HDMI 1.3 and DVI 1.0 compatible

HDCP 1.x compliant

Multiple video and audio inputs: 3 HDMI, 3 VGA, 1 Component Video, 1

Composite Video, and 8 Stereo audio

Supports switching and scaling of multiple AV inputs for display over

mirrored HDMI, HDBaseT and VGA outputs

Supports input and output resolutions up to 1080p/WUXGA(RB)

Supports pass-through of LPCM 2.0 audio

Supports 3D de-interlace, noise reduction, and 3D comb ltering for

composite video sources

Frame rate conversion support

Supports analogue to digital (ADC) and digital to analogue (DAC)

audio conversion, insertion and extraction

Quick output resolution switching via hot keys

HDBaseT feature support: HD Video and Audio, Ethernet, 48V PoH, and

Control (bidirectional IR/RS-232 pass-through)

HDBaseT output provides 48V PoH (PSE) power to compatible HDBaseT

Receivers (PD)

Supports EDID and HDCP management

Remote control provides discrete input source selection

Controllable via front panel controls with OSD, RS-232, Telnet, WebGUI,

and IR remote

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

POWER CV COMP PC 1PC 2PC 3 HDMI 1 HDMI 2 HDMI 3 MENU

XGA

ENTER

720P

EL-7500V

2 3 4 5 61

1POWER Button & LED: Press this button to power the unit on or place

it into stand-by mode. The LED will be lit when the unit is receiving

power.

Note: The power switch on the back of the unit must also be in the “On”

position for the unit to receive power.

2IR Window: Accepts IR signals from the included IR remote for control

of this unit only.

3CV/COMP/PC 1~3/HDMI 1~3 Buttons & LEDs: Press any of these

buttons to switch immediately to the corresponding input. An LED

will illuminate to indicate which source is currently selected.

4MENU Button: Press to enter the OSD menu, or to back out from

menu items.

5− & + Buttons: Press to navigate or to adjust selections within the

OSD menu.

6ENTER Button: Press to confirm a selection within the OSD or to go

deeper into a menu item.

Note: Pressing “ENTER” and “+” together will reset the output resolution to

XGA (1024×768@60Hz). Pressing “ENTER” and “−” together will reset the

output resolution to 720p@60Hz.

6.2 Rear Panel

RS-232 BYPASS RS-232 COAX. AUDIO

LAN

AUDIO

INPUT SERVICE

HDMI HDMI 1 HDMI 2 HDMI 3PC 1PC 2PC 3Cr/Pr Cb/Pb YRLCVPOWER

DC 24V

PC/HD

OUTPUT

BLASTER

IR RL

EXTENDER

CAT5e/6/7

OUTPUT

1 7 89 10 13

2 3 4 5 6 11 12 14

1CAT5e/6/7 OUT: Connect to a compatible HDBaseT Receiver with a

single Cat.5e/6/7 cable for transmission of all data signals.

HDMI OUT: Connect to an HDMI TV, monitor or amplifier for digital

video and audio output.

PC/HD OUT: Connect to a monitor/display for video output. For HD

(Component) output, use the supplied D-Sub 9-pin to 3 RCA adaptor

cable for HD resolutions from 480p~1080p.

Note: When the selected HDMI input source signal has HDCP content the

VGA/Component output will not display any image.

2IR EXTENDER: Connect to the provided IR Extender to extend the

IR control range of remotely located devices. Ensure that the remote

being used is within direct line-of-sight of the IR Extender.

3IR BLASTER: Connect to an IR Blaster to transmit IR signals to devices

within direct line-of-sight of the IR Blaster.

4RS-232 BYPASS: Connect to a PC, laptop or other serial control device

for the extension of RS-232 signals across the HDBaseT connection.

5RS-232: Connect directly to a PC, laptop or other serial control device

to send RS-232 commands to control the unit.

6COAX OUT: Connect to an amplifier or active speakers for digital

audio output.

Note: When the AUDIO SOURCE setting is set to “AUTO” the coaxial output

supports passing standard HDMI 1.2 bitstream formats.

AUDIO OUT: Connect to an amplifier or active speakers for audio

output in stereo format.

Note: If the source format is bitstream, this output will be muted

automatically.

7HDMI IN 1~3: Connect to HDMI source equipment such as media

players, game consoles or set-top boxes.

AUDIO IN 1~3: Connect to the stereo analogue output of the device

connected to the paired HDMI input port.

Note: If the AUDIO SOURCE setting is set to “AUTO” and the HDMI input

contains audio, it will have priority over the analogue input.

8PC IN 1~3: Connect to VGA source equipment such as a PC or laptop.

AUDIO IN 4~6: Connect to the stereo analogue output of the device

connected to the paired VGA input port.

9YPbPr & L/R IN: Connect to component (YPbPr) video source

equipment with stereo audio such as DVD players or set-top boxes.

10 CV & L/R IN: Connect to composite video source equipment with

stereo audio such as DVD players or VCRs.

11 LAN: Connect directly, or through a network switch, to your PC/

laptop to control the unit via Telnet/WebGUI and to extend the

network to both ends of the HDBaseT connection.

12 SERVICE: Reserved for manufacturer use only.

13 POWER Switch: Flip this switch to provide power to the unit or to turn

it completely off.

Note: This unit’s power stand-by functionality will not work if this switch is

in the “Off” position.

14 DC 24V: Plug the 24V DC power adapter into this port and connect it

to an AC wall outlet for power.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario