CTA PAD-ADMA Manual de usuario

888-733-4448

CONTENTS:

INSTRUCTIONS:

2A. When the C-Clamp is securely

attached to a surface, use the

provided security tool, attach to

security component, and rotate

closewise to put the C-Clamp in an

‘locked’ state. To loosen, rotate

counterclockwise with the security

tool.

Remove arm from the base

clamp mount. Repeat steps

in reverse to re-install

connection

2B. Align the (2) dimples on the underneath of the

security tool into the two holes on the security

component on the clamp as shown above

2C. Rotate counter-clockwise to

loosen and place the clamp in an

‘unlocked’ state. Continue rotating

until there is enough slack to rotate

the knob.Turn it clockwise to tighten

and place the clamp in a ‘locked’

state.

2

BASE CLAMP SECURITY SETUP

BASE MOUNT INSTALLATION ARM TO BASE CLAMP

ADJUSTMENTS

If you need to remove the arm

from the base clamp, take the

provided larger allen key tool,

rotate, and loosen connection

12

3

Find the included base

pad (shown above) and

peel off the backing. Align

to the underneath of the

C-Clamp and apply pad. While the clamp is in unlocked mode, rotate the

knob at the bottom (as shown above) to loosen

or securely tighten to the table top.

ALIGNING SECURITY TOOL WITH SECURITY COMPONENT

Unlock by moving the

red lever over to

unlock position

Lock by pressing claw

arms back in around

device, then moving

lever into lock position.

Unlock by making sure

key is inserted and

then moving the red

lever over to unlock

Lock by pressing claw

arms back in around

device, then moving

lever into lock position,

then removing the key

888-733-4448

When charging your device, find

the port, then route your cable

through the opening on the ends of

the holder arms.

When routing cables for the from

device to the power source, use

provided clips as shown to keep

the cables organized and tight to

the arms to avoid any slack.

Each hinge of the product can be

adjusted easily with the provided

smaller allen key tool. Loosen to adjust

and securely tighten after preferred

position is set.

When all hinges and joints are tightened, do not attempt to

forcibly flex the angles or positioning without loosening. Any

attempt to do so will possibly have an effect on product integrity

and CTA and manufacturer will not be responsible for any

mishandling.

TABLET INSTALLATION

JOINT ADJUSTMENTS CHARGING

SETUP

CABLE

ROUTING

4

567

Otros manuales de Rack y soporte de CTA

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario