CTA AUT-VDMC Manual de usuario

Tabla de contenidos

Otros manuales de Rack y soporte de CTA

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario

Vehicle Dash Mount w/ Custom Flex Arms

AUT-VDMC

INSTALLATION - MANUAL

INSTALLATION:

1.Installing the Mount to Vehicle :

1A. Drill holes on the surface as shown above

with power drill tool (not provided).

1B. Place vehicle dash mount (B) aligning the holes

drilled on surface and then screw in the provided x4

screws (C) through the base with a screw driver (not

provided) until securely tightened.

A

A

CONTENTS:

x4 Screws

C

x3

Foam

Pads

B

1mm

5mm

10mm

x1

Vehicle

Dash Mount

A

Drilling into the dash, wall, or roof will be a permanent installation and may cause damage if not

installed properly. Use caution and consult a mobile install professional to avoid drilling into the gas

tank,electrical system or other highly sensitive vehicle components.

2.Attaching Foam Pad to Tablet Holder :

3. Inserting Tablet to Holder :

4. Adjustability

A

B

3A. Press quick release button on side of tablet

holder (A) to release the adjustable end.

3B. Insert tablet corner against the spring arm. Push adjustable arm

down against opposite corner (A). Be sure it is as snug as possible.

1.Twist the screw knobs

counter clock-wise to loosen

joints

2. Adjust the arm to desired position

then twist the screw knob clock-wise

until securely tightened.

2A. Select the appropiate foam pad (B) according to the thickness of your tablet (or tablet in its case), then

press adhesive side into center of the tablet holder.

1mm

5mm

10mm

Please be sure to fasten all the screws were

tightened securely while using the stand.

Not for use while driving.

Max loading :1KG

Do not install CTA’s products over an air bag

cover or within the air bag deployment zone.

CTA Digital, Inc. assumes no respons of liability

for injury or death as a result of car crashes and

/ or air bag deployment. CTA is not responsible

for any damages caused to your vehicle, your

device, or yourself due to the installation or use

of this product.

Caution

Safety Precautions

- Use this table to determine the appropiate

foam pad (B) to use with your tablet.

Note: sizes refer to total tablet size with or

without a case

Tablet Thickness:

Foam Pad

Thickness:

1mm 0.67-1.06in / 17-27mm

0.51- 0.91in / 13-23mm

0.31- 0.71in / 8-18mm

5mm

10mm

A

**Tablet for illustration

only and not included

A

A