ACME BW-545 Manual de usuario

BW-545

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions............................................................................................................................2

2. Techical Specfications.......................................................................................................................4

3. How To Set The Fixture ....................................................................................................................4

3.1 Control Panel..................................................................................................................................4

3.2. Main Functions..............................................................................................................................5

4.How To Control The Unit .................................................................................................................10

4.1 Master/Slave Built In Preprogrammed Function .........................................................................10

4.2 DMX Controller.............................................................................................................................10

4.3 DMX 512 Configuration................................................................................................................11

4.4 DMX512 Connection ....................................................................................................................13

5. Troubleshooting .............................................................................................................................14

6. Fixture Cleaning .............................................................................................................................14

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Caution

：

All fixtures are intact from the manufacturer, please operate follow up the user manual,

artificial fault are not under guarantee repair.

Unpack and check carefully there is no transportation damage before using the unit.

Do install and operate by operator.

Use safety chain when fixes the unit.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Maximum ambient temperature TA : 40℃. Don’t operate it where the temperature is higher

than this.

Don’t connect the device to any dimmer pack.

First run, there will be smoke or smells, and all disappearing a few minutes later.

Make sure there are no flammable materials close to the unit while operating, as it is fire

hazard.

Look over power wires carefully, replace immediately if there is any damage.

Unit surface temperature may reach up to 60℃. Don’t touch the housing bare-hand during its

operation.

Never run on for a long time lest shortening lifespan.

Do not operate in dirty and dusty environment, also cleaning fixtures regularly.

Do not allow children to operate the fixture.

Please read the instructions carefully which include important

information about the installation, operation and maintenance.

Do not touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together arounding other cables.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Do not open the unit as there are no user serviceable parts inside. Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center.

Disconnect the mains power if the fixture is not used for a long time.

Do use original packing materials once transport it again.

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

Do not look directly at the LED light beam while the fixture is on.

To protect the machine, power off 10s rear can electrify.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the

unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit

when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people and has no one pass by or under it.

2. Techical Specfications

Voltage: AC 100-240V/50HZ

Power consumption: 162W

Light source: 3W LED x 54pcs (14pcs x Red, 14pcs x Green, 14pcs x Blue, 12pcs x White)

Power Cord Daisy Chain: 3 Fixtures Max. (120V/60Hz), 6 Fixtures Max. (230V/5 0Hz)

Lens Option: 19 Degree

Dimension: 230 x 302 x 350 mm

Weight

：

9 kg

3. How To Set The Fixture

3.1 Control Panel

1: Power

Water proof connectors for power input/output

2: DMX input/output

Water proof connectors for DMX 512 operation, 3-pin XLR cable to link the units together

3: Display

To show the menu and the selected functions

Button:

3.2. Main Functions

To select any functions, press the MENU button until the required one is shown on the display.

Select the function by the ENTER button and the display will blink. Use the DOWN and UP button

to change the mode. Once the required mode has been selected, press the ENTER button to setup

or it will automatically return to the main functions without any change after idling one minute.

Back to the functions without any change press the MENU button. The main functions are shown

below:

4. MENU

To select the programming functions

5. DOWN

To go backward in the selected functions

6. UP

To go forward in the selected functions

7. ENTER

To confirm the selected functions

Once you set to , after running in show mode for 5 minutes

without any change or restarting the unit, the key board become locked.

Press ENTER button to enable the menu, the display will show , press

UP and DOWN button until it shows , then press ENTER to unlock.

DMX 512 Address Setting

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the

address has been selected, press ENTER button to setup or automatically exit menu mode without

any change after one minute. Back to the previous functions without any change press MENU

button.

Channel mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (4 channels),

(5 channels) or (7 channels). Once select, press ENTER button to setup or

automatically exit menu mode without any change after one minute. To go back to the functions

without any change press the MENU button.

Show mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (show 1) …

(show 16) or (Manual). After select the show mode, use DOWN and UP button to

adjust the value for fade mode and speed mode. Once select, press ENTER button to store or

automatically return to the main functions without any change after one minute. To go back to the

previous functions without any change press the MENU button.

Slave mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Master),

(slave 1) or (slave 2). Once select, press ENTER button to store or automatically return

to the main functions without any change after one minute. To go back to the previous functions

without any change press the MENU button.

Dimmer mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Dimmer Curve

1) … (Dimmer Curve 4). Once select, press ENTER button to store or automatically return

to the main functions without any change after one minute. To go back to the previous functions

without any change press the MENU button.

Dimmer Speed

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Smooth),

(Fast). Once select, press ENTER button to store or automatically return to the main functions

without any change after one minute. To go back to the previous functions without any change

press the MENU button.

DMX State

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Master-Slave) or

(Blackout mode). Once select, press ENTER button to store or automatically return to

the main functions without any change after one minute. To go back to the previous functions

without any change press the MENU button.

Blackout mode

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (On) or

(Off). Once select, press ENTER button to store or automatically return to the main functions

without any change after one minute. To go back to the previous functions without any change

press the MENU button.

Display

Press the MENU button up to when the is shown on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Normal) or

(Off). Once select, press ENTER button to store or automatically return to the main

functions without any change after one minute. To go back to the previous functions without any

change press the MENU button.

White Balance

Press the MENU button up to when the is showing on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Red),

(Green) or (Blue) mode. Once the mode has been selected, press the DOWN and Up

button to select the value from 125 to 255, press the ENTER button to setup or automatically

return to the main functions without any change after one minute. To go back to the previous

functions without any change press the MENU button.

Manual Test

Press the MENU button up to when the is showing on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Red),

(Green), or (Blue), (White), (Color), (Dimmer) or

(Strobe) mode. Once the mode has been selected, press the DOWN and Up button to

select the value from 0 to 255, press the ENTER button to setup or automatically return to the

main functions without any change after one minute. To go back to the previous functions without

any change press the MENU button.

Key Board Lock

Press the MENU button up to when the is showing on the display. Press ENTER button

and the display will blink. Use DOWN and UP button to select the (Key board lock On)

or (Key board lock Off). Once select, press the ENTER button to setup or automatically

return to the main functions without any change after one minute. Back to the previous functions

press MENU button.

Self-Test

Press the MENU button up to when the is blinking on the display. Press ENTER button

and the unit will run self-test by built-in program. To go back to the functions press the MENU

button again.

Temperature Test

Press the MENU button up to when the is blinking on the display. Press ENTER button

and the display will show the temperature of the unit. To go back to the functions press the MENU

button again.

Tabla de contenidos

Otros manuales de Foco de ACME

ACME

ACME LED-ST2000 Manual de usuario

ACME

ACME TS-300M CW Manual de usuario

ACME

ACME theatre spot 150 TS-150 CW Manual de usuario

ACME

ACME MEGA STROBE 5000 Manual de usuario

ACME

ACME Invincibled LED-767RGBWII Manual de usuario

ACME

ACME LED-GBF Manual de usuario

ACME

ACME DVS-2500 Manual de usuario

ACME

ACME LED-192RGB Manual de usuario

ACME

ACME LED-ST50 Manual de usuario

ACME

ACME XPerior 700WZA Manual de usuario

ACME

ACME PAGEANT CM-600z Manual de usuario

ACME

ACME LP-900 Manual de usuario

ACME

ACME Butterfly quard Manual de usuario

ACME

ACME LITE PANEL 900 LP-900 WW BD30 Manual de usuario

ACME

ACME LED-7474 Manual de usuario

ACME

ACME LED-LP400 Manual de usuario

ACME

ACME LED-737 Manual de usuario

ACME

ACME REFracted RLS 100 Manual de usuario

ACME

ACME BARRAGE LED-248 Manual de usuario

ACME

ACME Dragonfly Manual de usuario

ACME

ACME Super Splash Manual de usuario

ACME

ACME MEGA STROBE 5000 RGB Manual de usuario

ACME

ACME CB-348TC Manual de usuario

ACME

ACME SUPER NOVA RGB Manual de usuario

Manuales populares de Foco de otras marcas

VIZULO

VIZULO Micro Martin Guía del usuario

EuroLite

EuroLite LED IP FL-100 SMD Manual de usuario

Cooper Wheelock

Cooper Wheelock XB12 Manual de usuario

Allen + Roth

Allen + Roth 17624-000 Manual de usuario

ADJ

ADJ 4 STAGE PAK Manual de usuario

Cooper Lighting

Cooper Lighting EGL91SW233 Manual de usuario

Max

Max 37496 Manual de usuario

BEGA

BEGA 85 143 Manual de usuario

Beamz

Beamz 151.226 Manual de usuario

EuroLite

EuroLite LED IP FL-8 Manual de usuario

Ledj

Ledj PERFORMER 36 RGB Manual de usuario

Perel

Perel ELS3 Manual de usuario

Perel

Perel ELS3WD Manual de usuario

LumX

LumX LM 36130 Manual de usuario

Xtricity

Xtricity 4-80053 Manual de usuario

Stahl

Stahl 6521/4 Series Manual de usuario

Ecosense

Ecosense EcoSpec Manual de usuario

Ayrton

Ayrton minipanel FX Manual de usuario