ACME BARRAGE LED-247 Manual de usuario

BARRAGE

LED-247

User Manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions

2. Technical Specifications

3. How to Set the Fixture

4. How to Control the Fixture

5. DMX 512 Configuration

6. DMX 512 Connections

7. Troubleshooting

8. Fixture Cleaning

1. Safety Introductions

WARNING

Please keep this User Manual for future consultation. If you sell the fixture to another

user, be sure that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the fixture.

It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

Disconnect main power before servicing and maintenance.

Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is

higher than this.

In the event of serious operating problem, stop using the fixture immediately. Never try

to repair the fixture by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance

center. Always use the same type spare parts.

Do not connect the unit to any dimmer pack.

Do not touch any wire during operation and there may be a hazard of electric shock.

To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain

or moisture.

The housing must be replaced if they are visibly damaged.

Do not look directly at the LED light beam while the fixture is on.

There are no user serviceable parts inside the fixture. Do not open the housing or

attempt any repairs by yourself. In the unlikely event your fixture may require service,

please contact your nearest dealer.

Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.

Direct sunlight can cause heat to build up inside of the unit, which will seriously damage

unit.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

2. Technical Specifications

Input Voltage: 100V~240V 50/60Hz

Power consumption:21.6W

LED:3W LED, Total 8pcs,

Red 2pcs, Green 2pcs, Blue 2pcs, White 2pcs

Dimension: 510 x 120 x 150.8 mm

Weight: 4.3kgs

3. How to Set the Fixture

3.1 Rear panel

○

1Hanging bracket: With 2 knobs on both sides to fasten the unit and a mounting hole to

fix a mounting hook.

○

2Rotating optical barrel: Don’t touch while in use.

○

3DISPLAY: Shows the various menus and the selected functions.

○

4Button:

To select the programming functions

DOWN

To go backward in the selected functions

To go forward in the selected functions

ENTER

To confirm the selected functions

○

5LED:

○

6 /○

7 Only for remote control: Connecting with CA-8/CA-9/CA-9RTX to control the unit

for Stand by, Function and Mode function.

○

8Microphone: Receives the sound to control the unit

○

9 Safe Ring: For attached the safe cable.

○

10 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal

○

11 DMX output: For DMX512 link, use 3-pin XLR plug cable to link the next unit.

○

12 Mains output: Connect to supply power for the next unit.

○

13 Mains input: Connect to power supply.

3.2Main Function

To select any of the given functions, press the MENU button to show the required option on

the display. Select the function with the ENTER button and the display will blink. Use the

DOWN and UP buttons to change the mode. Once the required mode has been selected,

Press the ENTER button to store. To go back to the main menu without any changes press

the MENU button. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode. The main functions are shown below:

DMX

DMX input present

MASTER

Master Mode

SLAVE

Slave Mode

SOUND

Flashing

Sound activation

DMX Address Setting

Press the MENU button to show on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to change the DMX address. Once the

address has been selected, press the ENTER button to store. To return to the main menu

without any changes press the MENU button. Hold and press the MENU button about one

second or wait for one minute to exit the menu mode.

Slave Mode

Press the MENU button to show on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the (Master)

(slave 1) or (Slave 2) mode. Once selected, press the ENTER button to store. To

return to the main menu without any changes press the MENU button. Hold and press the

MENU button about one second or wait for one minute to exit the menu mode.

Show Mode

Press the MENU button to show on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the (Auto show) or

(show 1) or (Show 2) or … or (show 8).Once selected, press the

ENTER button to store. To return to the main menu without any changes press the MENU

button. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Sound Mode

Press the MENU button to show on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the (sound on) or

(sound off). Once selected, press the ENTER button to store. To return to the main

menu without any changes press the MENU button. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

Sound Sensitivity

Press the MENU button to show on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to change the sound sensitivity (0-100) of

the unit. Once selected, press the ENTER button to store. To return to the main menu

without any changes press the MENU button. Hold and press the MENU button about one

second or wait for one minute to exit the menu mode.

Blackout mode

Press the MENU button to show on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the (blackout) or

(normal). Once selected, press the ENTER button to store. To return to the main

menu without any changes press the MENU button. Hold and press the MENU button about

one second or wait for one minute to exit the menu mode.

LED display

Press the MENU button to show on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the (display on) or

(display off) mode. Once selected, press the ENTER button to store. To return to the

main menu without any changes press the MENU button. Hold and press the MENU button

about one second or wait for one minute to exit the menu mode.

Display Inverse

Press the MENU button to show on the display. Press the ENTER button and the

display will blink. Use the DOWN and UP buttons to select the (normal) or

(inverse), Once selected, press the ENTER button to store. To return to the main menu

without any changes press the MENU button. Hold and press the MENU button about one

second or wait for one minute to exit the menu mode.

Self-Test

Press the MENU button to show on the display. Press ENTER button and the unit

will run the built-in programmer for self-test. To return to the main menu press the MENU

button. Hold and press the MENU button about one second or wait for one minute to exit the

menu mode.

Fixture Hours

Press the MENU button to show on the display. Press the ENTER button and the

display will show the number of working hours of the unit. To return to the main menu press

the MENU button. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode.

Software version

Press the MENU button to show on the display. Press the ENTER button and the

display will show the version of software inside the unit. To return to the main menu press

the MENU button. Hold and press the MENU button about one second or wait for one

minute to exit the menu mode.

Reset

Press the MENU button to show on the display. Press ENTER button and all

channels of the unit will return to their standard position.

4. How To Control The Unit

You can operate the unit in three ways:

1. Master/slave built-in preprogram function

2. Easy controller

3. Universal DMX controller

There is no need to turn the unit off when you change the DMX address, as new DMX

address setting will be effected at once. Every time you turn the unit on, it will show

“ ” on the display. After that the unit will be ready to receive a DMX signal or run the

built in programs.

4.1 Master/Slave Built In Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the other units to

give an automatic, sound activated, synchronized light show. This function is good when you

want an instant show. You have to set the first unit in master mode and select (auto

show), (show 1) or …or (show 8). Its DMX input jack will have nothing

plugged into it, and Its master LED will be constantly on and sound LED will flash to the

music. The slave units will have to select (normal) or (2 light show) mode,

Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave led lights will

constantly on.

2-light show

In slave mode, means the unit works as the master unit and or

means 2-light show. In order to create a great light show, you can set or

on the second unit to get contrast movement to each other, even if you have only two units.

4.2. Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. By connecting

to the 1/4” microphone jack of the first unit, you will find that the remote

controller on the first unit will control all the other units in Stand by, and Mode

selection.

Tabla de contenidos

Otros manuales de Foco de ACME

ACME

ACME LED-CTL6 Manual de usuario

ACME

ACME XPerior 700WZA Manual de usuario

ACME

ACME PAGEANT CM-600z Manual de usuario

ACME

ACME MEGA STROBE 5000 Manual de usuario

ACME

ACME LITE PANEL 900 LP-900 WW BD30 Manual de usuario

ACME

ACME LED-737 Manual de usuario

ACME

ACME LED-192RGB Manual de usuario

ACME

ACME IM-5S-ELC Manual de usuario

ACME

ACME Invincibled LED-767RGBWII Manual de usuario

ACME

ACME REFracted RLS 100 Manual de usuario

ACME

ACME LED-ST50 Manual de usuario

ACME

ACME LED-4TC Manual de usuario

ACME

ACME LP-900 Manual de usuario

ACME

ACME Butterfly quard Manual de usuario

ACME

ACME DMX 512 Manual de usuario

ACME

ACME MEGA STROBE 5000 RGB Manual de usuario

ACME

ACME TS-300M CW Manual de usuario

ACME

ACME TV PANEL200 Manual de usuario

ACME

ACME theatre spot 150 TS-150 CW Manual de usuario

ACME

ACME LED-ST2000 Manual de usuario

ACME

ACME Dynamic 25 Spin LED?GF25 Manual de usuario

ACME

ACME CP?64 BD15 Manual de usuario

ACME

ACME DVS-2500 Manual de usuario

ACME

ACME Super Splash Manual de usuario

Manuales populares de Foco de otras marcas

VIZULO

VIZULO Micro Martin Guía del usuario

EuroLite

EuroLite LED IP FL-100 SMD Manual de usuario

Cooper Wheelock

Cooper Wheelock XB12 Manual de usuario

Allen + Roth

Allen + Roth 17624-000 Manual de usuario

ADJ

ADJ 4 STAGE PAK Manual de usuario

Cooper Lighting

Cooper Lighting EGL91SW233 Manual de usuario

Max

Max 37496 Manual de usuario

BEGA

BEGA 85 143 Manual de usuario

Beamz

Beamz 151.226 Manual de usuario

EuroLite

EuroLite LED IP FL-8 Manual de usuario

Ledj

Ledj PERFORMER 36 RGB Manual de usuario

Perel

Perel ELS3 Manual de usuario

Perel

Perel ELS3WD Manual de usuario

LumX

LumX LM 36130 Manual de usuario

Xtricity

Xtricity 4-80053 Manual de usuario

Stahl

Stahl 6521/4 Series Manual de usuario

Ecosense

Ecosense EcoSpec Manual de usuario

Ayrton

Ayrton minipanel FX Manual de usuario