ACME LED-CTL6 Manual de usuario

LED CENTER LIGHT

USER MANUAL

LED-CTL6

Professional Entertainment Technology

LED-CTL6

 1-

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Main Function

4. How To Control the Unit

5. DMX 512 Configuration

6. DMX 512 Connection

7. Fixture Cleaning

LED-CTL6

 2-

1. Safety Instruction

WARNING

♦Please keep the User Manual for future consultation. If you sell the unit to another

user, be sure that they also receive this instruction booklet.

♦Unpack and check carefully there is no transportation damage before using the unit.

♦Before operating, ensure that the voltage and frequency of power supply match the

power requirements of the unit.

♦It’s important to ground the yellow/green conductor to earth in order to avoid electric

shock.

♦The unit is for indoor use only. use only in a dry location.

♦The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

♦Disconnect mains power before servicing.

♦Replace fuse only with the same type.

♦Make sure there is no flammable materials close to the unit while operating as it is

fire hazard.

♦Use safety cable when fix the unit.

♦Maximum ambient temperature is Ta: 40℃. Don’t operate it where the temperature is

higher than this.

♦In the event of serious operating problem, stop using the unit immediately. Never try

to repair the unit by yourself. repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance

center. Always use the same type spare parts.

♦Don’t connect the device to any dimmer pack or power pack.

♦Do not touch any wire during operation as high voltage might be causing electric

shock.

Please read the instruction carefully which including important

information about the installation, operation and maintenance

LED-CTL6

 3-

Warning

♦To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain

or moisture.

♦Do not start on the unit when housing are damaged.

♦The housing must be replaced if they are visibly damaged.

♦Do not look directly at the light while the bulb is on.

Caution

There are no user serviceable parts inside the unit. Do not open the housing or attempt

to any repair yourself. In the unlikely event your unit may require service please contact

your nearest dealer.

Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. And make sure that

the structure to which you are attaching the unit is secure and is able to support a

weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12

times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is

out of the touch of people and has no one pass by or under it.

LED-CTL6

 4-

2. Technical Specification

yInput Voltage: AC 100/120/230/250V~50/60Hz

yPower consumption: 60W

yLight Source: 6×3W (3 in 1) LED

yFuse: T 5A (AC 100/120V)

T 3.15A (AC 230/250V)

y4 Channels:

Channel 1 = Movement

Channel 2 = Movement Speed

Channel 3 = Color Macro

Channel 4 = Color Macro Speed

yDimension: 478 x 414 x 152 mm

yWeight: 10kgs

yLuminous intensity:

LED-CTL6

 5-

3. Main Function

1. Mains input：IEC socket and integrated fuse holder, connect to main power cable.

2. DMX OUT：Transmit DMX signal by 3-Pin XLR female socket.

3. DMX IN：Receive DMX signal by 3-Pin XLR male socket.

4. Remote controller input：Connecting with 1/4” microphone jack to control the

scene for Stand by, Function, and Mode function

selections.

5. Microphone：Receive audio signal for sound activated.

6. Sensitivity：Adjust the sound-input sensitivity.

7. Dip switches：Dip 10 for Master/Slave setting such as Dip 10 ON is MASTER mode

and Dip 10 OFF is SLAVE mode. Dips 1-9 are used to set DMX

address of the unit.

LED-CTL6

 6-

4. How To Control The Unit

Three ways to operations:

A. Master/Slave operation

B. Easy controller

C. Universal DMX controller

A. By Master/slave Built-in Preprogrammed Function

By linking the units in master/slave connection, the first unit will control the others to

give a coordinate automatic light show and it’s good for instant shows. In this mode, the

first unit（Master）must be turn Dip switch 10 on. The first unit is easy to recognize by

nothing in its DMX input jack. The others of chains (Slaves) will have DMX cables

plugged into the DMX input jacks (daisy chain). Please refer to the diagram on setting

the Dip switches.

Slave 1 : dip / on : #1 ( 1 )

Slave 2 : dip / on : #1, #3 ( 1 + 4 =5 )

Slave 3 : dip / on : #1, #4 ( 1 + 8 = 9 )

Slave 4 : dip / on : #1, #3, #4 (1 + 4 + 8 =13)

B. By Easy Controller(CA-8)

The easy remote control is used only in master/slave mode. By connecting to the 1/4”

microphone jack of the first unit, you will find that the remote control on the first unit will

control all the other units for Stand by, Function and Mode programs.

LED-CTL6

 7-

C. By universal DMX controller

When using a universal DMX controller to control the chain of units, you have to set

DMX address by Dip switches from 1 to 9 to make sure all the units will receive its DMX

signal. Please refer to the following diagram to know how to address your DMX 512

system in the binary code.

DMX 512 Address Chart

Dip #1 #2 #3 #4 #5 #6 #7 #8 #9 #10

Value 1 2 4 8 16 32 64 128 256 M/S

•Examples:

Channel 1 : dip / on : #1 ( 1 )

Channel 5 : dip / on : #1, #3 ( 1+4 =5 )

Channel 9 : dip / on : #1, #4 ( 1 + 8 = 9 )

Channel 13 : dip / on : #1, #3, #4 (1+4+ 8 =13)

Blackout To blackout all the fixture

Function 1.Synchronous strobe

inwhite

2. Sound strobe

inwhite

3. Sound strobe

incolor

Select color

1. Red

2. Green

3. Orange

4. Pink

5. Yellow

6. Cyan

7.Blue

8.Magenta

9.White

Select chase

1-6

Mode Sound 1

(LED OFF) Manual

(LED ON) Sound 2

(LED slow blinking)

LED-CTL6

 8-

5. DMX 512 Configuration

6. DMX 512 Connection

The DMX 512 is widely used in intelligent lightings and with a maximum of 512

channels.

LED-CTL6

 9-

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120

ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug

and plug it in the DMX-output of the last unit.

3. Connect the unit together in a ‘daisy chain’ by XLR plug from the output of the unit

to the input of the next unit. The cable can not be branched or split to a ‘Y’ cable.

DMX512 is a very high-speed signal. Inadequate or damaged cables, solder joints

or corroded connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX

circuit, when one of the units’ power is disconnected.

5. Each lighting unit needs to have an address set to receive the data sent by the

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).

6. The end of the DMX512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

Pin 4/5 Not used

7. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out

periodically to optimize light output. Cleaning frequency depends on the environment in

which the fixture operates: damp, smoky or particularly dirty surrounding can cause

greater accumulation of dirt on the unit’s optics.

yClean with soft cloth using normal glass cleaning fluid.

yAlways dry the parts carefully.

yClean the external optics at least every 20 days. Clean the internal optics at least

every 30/60 days.

Tabla de contenidos

Otros manuales de Foco de ACME

ACME

ACME BARRAGE LED-247 Manual de usuario

ACME

ACME theatre spot 150 TS-150 CW Manual de usuario

ACME

ACME LED-737 Manual de usuario

ACME

ACME Dynamic 25 Spin LED?GF25 Manual de usuario

ACME

ACME MEGA STROBE 5000 Manual de usuario

ACME

ACME DMX 512 Manual de usuario

ACME

ACME Invincibled LED-767RGBWII Manual de usuario

ACME

ACME LED-192RGB Manual de usuario

ACME

ACME Butterfly quard Manual de usuario

ACME

ACME LED-GBF Manual de usuario

ACME

ACME CM-108 RGB Manual de usuario

ACME

ACME XPerior 700WZA Manual de usuario

ACME

ACME CP?64 BD15 Manual de usuario

ACME

ACME SUPER NOVA RGB Manual de usuario

ACME

ACME LED-7474 Manual de usuario

ACME

ACME LITE PANEL 900 LP-900 WW BD30 Manual de usuario

ACME

ACME LED-LP400 Manual de usuario

ACME

ACME MEGA STROBE 5000 RGB Manual de usuario

ACME

ACME LP-900 Manual de usuario

ACME

ACME TV PANEL200 Manual de usuario

ACME

ACME LED-ST50 Manual de usuario

ACME

ACME LED-4TC Manual de usuario

ACME

ACME LED-ST2000 Manual de usuario

ACME

ACME REFracted RLS 100 Manual de usuario

Manuales populares de Foco de otras marcas

VIZULO

VIZULO Micro Martin Guía del usuario

EuroLite

EuroLite LED IP FL-100 SMD Manual de usuario

Cooper Wheelock

Cooper Wheelock XB12 Manual de usuario

Allen + Roth

Allen + Roth 17624-000 Manual de usuario

ADJ

ADJ 4 STAGE PAK Manual de usuario

Cooper Lighting

Cooper Lighting EGL91SW233 Manual de usuario

Max

Max 37496 Manual de usuario

BEGA

BEGA 85 143 Manual de usuario

Beamz

Beamz 151.226 Manual de usuario

EuroLite

EuroLite LED IP FL-8 Manual de usuario

Ledj

Ledj PERFORMER 36 RGB Manual de usuario

Perel

Perel ELS3 Manual de usuario

Perel

Perel ELS3WD Manual de usuario

LumX

LumX LM 36130 Manual de usuario

Xtricity

Xtricity 4-80053 Manual de usuario

Stahl

Stahl 6521/4 Series Manual de usuario

Ecosense

Ecosense EcoSpec Manual de usuario

Ayrton

Ayrton minipanel FX Manual de usuario