Zortrax M Series Manual de uso y cuidado

Endstop Replacement

SOURCE:

https://support.zortrax.com/endstop-replacement/

page 1 / 9

Table Of Content

Unplugging the Power Cable 4

Unscrewing the Endstop 5

Endstop Removal 6

Plugging the Cables into the Endstop 7

Endstop Assembly 8

Plugging the Power Cable 9

page 2 / 9

The endstop is an extruder movement control tool which is responsible for

sensing the extruder’s position. Each M Series and M Series Plus printer is

equipped with two endstops – one located at the end of the X axis and the other at

the end of the Y axis, both are located in the front corners of the housing. Once

the extruder reaches the end of the axis, the lever of the endstop is pressed with

an endstop sleeve – the element placed on the inner side of the axis block. This

action immediately informs the printer that the extruder should stop moving and

not crash into the housing. Therefore, if the extruder hits a corner of the housing,

and an error message appears on the display (Endstops error #034), at first check

if the endstop cables are properly connected to each endstop. Then, check if the

endstop sleeves are installed on each axis block. If everything seems to be in

order, the endstops need to be replaced. Follow the steps from this manual to see

the correct replacement procedure. This manual shows the Y axis endstop

replacement. The X axis endstop should be replaced likewise.

The following manual shows the M200 repair work. For the M300, M200 Plus and M300

Plus, these procedures are the same.

page 3 / 9

Unplugging the Power Cable

Turn off the printer and unplug the power cable.

page 4 / 9

Unscrewing the Endstop

Unscrew the two screws that secure the endstop in the housing. Use a 2mm Allen key.

page 5 / 9

Endstop Removal

Gently grab the endstop, pull it out and unplug the cables.

page 6 / 9

Plugging the Cables into the Endstop

Plug the cables into the new endstop.

Remember to keep a proper connection system. One cable must be connected to the

pin no. 1 and the other cable to the pin no. 3. The pins are marked on the endstop.

page 7 / 9

Endstop Assembly

Install the new endstop in its place and secure it with the screws.

page 8 / 9

Plugging the Power Cable

Plug the power cable in.

Powered by TCPDF (www.tcpdf.org)

page 9 / 9

Este manual sirve para los siguientes modelos

5

Tabla de contenidos

Otros manuales de Impresora 3D de zortrax

zortrax

zortrax M200 Plus Manual de usuario

zortrax

zortrax Inkspire Manual de usuario

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax M300 Instrucciones de uso

zortrax

zortrax Z-PLA Pro Instrucciones de montaje

zortrax

zortrax Z-Axis Manual de uso y cuidado

zortrax

zortrax Inventure Manual de usuario

zortrax

zortrax M200 Plus Guía

zortrax

zortrax M200 Plus Manual de usuario

zortrax

zortrax M200 Manual de uso y cuidado

zortrax

zortrax M200 Manual de uso y cuidado

zortrax

zortrax Inkspire Manual de usuario

zortrax

zortrax M200 Manual de funcionamiento

zortrax

zortrax M200 Manual de funcionamiento

zortrax

zortrax X/Y Manual de usuario

zortrax

zortrax M300 Manual de usuario

zortrax

zortrax M200 Plus Guía de instalación

zortrax

zortrax Z-NYLON Instrucciones de montaje

zortrax

zortrax Inkspire 2 Manual de usuario

zortrax

zortrax Z-PETG Manual de usuario

zortrax

zortrax M200 Plus Manual de usuario

zortrax

zortrax M300 Manual de usuario

zortrax

zortrax M200 Manual de uso y cuidado

zortrax

zortrax M200 Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario