Zortrax Z-NYLON Instrucciones de montaje

Tips for Printing with Z-NYLON

SOURCE:

https://support.zortrax.com/z-nylon-tips/

Table Of Content

Storage & Preparation 3

Hardware Requirements 4

Model Preparation Tips 5

Printing Process Requirements 6

Storage & Preparation

Z-NYLON is highly hydroscopic and shouldn’t be stored without protection in humid

environments for a long time. Unused spools have to be stored in an airtight container

with a moisture absorber. Otherwise, the filament will absorb moisture from air which can

cause problems such as stringing or low surface quality of printed parts. Also, the color

of the filament can fade or become dull.

To remove moisture from the filament, perform a drying procedure at 90 °C [194 °F] for

2 hours.

Hardware Requirements

To create the best printing environment for Z-NYLON, it is best to equip your printer with

a separate hotend and a perforated plate that will be dedicated only for printing with this

material. These parts should be new and not used with other materials.

Also, avoid using adhesive substances with the new perforated plate.

Model Preparation Tips

As all nylon-based materials, Z-NYLON is highly prone to warping. That’s why, while

preparing your model in Z-SUITE, go to Advanced section in the Print settings step and

set the Fan speed to 0%.

If you’re preparing several small models for printing, make sure to separate them in the

workspace so that each item has its own raft structure. This way, a smaller printing area

can reduce the risk of warping.

Printing Process Requirements

While printing with Z-NYLON, it is recommended to provide proper conditions in the print

room. First of all, make sure that there are no draughts in your work area. Strong

airflows cause warping and may damage your print. Also, avoid printing in humid

conditions. Due to its high shrinkage, Z-NYLON is not recommended for printing large

geometric models with steep slopes in the Z axis. In general, models with walls that are

perpendicular to the platform will be less prone to warping. Still, it is advisable to add

support structures to all angles and overhanging parts of your model.

To reduce shrinkage, it is advisable to create a printing chamber with the use of Side

Covers and a HEPA Cover. These accessories have been designed to support the

printing process with materials of a high shrinkage rate.

Lastly, remove any residues of material extruded during the pre-print calibration. This will

facilitate adhesion of raft and the whole model to the perforated plate.

Powered by TCPDF (www.tcpdf.org)

Tabla de contenidos

Otros manuales de Impresora 3D de zortrax

zortrax

zortrax M200 Manual de funcionamiento

zortrax

zortrax M200 Manual de uso y cuidado

zortrax

zortrax M300 Manual de usuario

zortrax

zortrax Inventure Manual de usuario

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax M200 Manual de uso y cuidado

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax M200 Plus Guía de instalación

zortrax

zortrax Inkspire Manual de usuario

zortrax

zortrax M200 Plus Manual de uso y cuidado

zortrax

zortrax M200 Plus Manual de usuario

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax M200 Plus Manual de usuario

zortrax

zortrax Z-Axis Manual de usuario

zortrax

zortrax M200 Manual de uso y cuidado

zortrax

zortrax Z-Axis Manual de uso y cuidado

zortrax

zortrax M300 Plus Manual de usuario

zortrax

zortrax M300 Manual de usuario

zortrax

zortrax Inkspire 2 Manual de usuario

zortrax

zortrax M200 Plus Manual de usuario

zortrax

zortrax Inkspire Manual de usuario

zortrax

zortrax Z-PLA Pro Instrucciones de montaje

zortrax

zortrax M300 Manual de funcionamiento

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario