Zortrax Z-Axis Manual de uso y cuidado

Otros manuales para Z-Axis

1

Tabla de contenidos

Otros manuales de Impresora 3D de zortrax

zortrax

zortrax M200 Plus Manual de usuario

zortrax

zortrax M200 Manual de uso y cuidado

zortrax

zortrax M200 Plus Manual de usuario

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax Inkspire Manual de usuario

zortrax

zortrax Inkspire Manual de usuario

zortrax

zortrax Inkspire 2 Manual de usuario

zortrax

zortrax M200 Manual de uso y cuidado

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax Curing Station Manual de usuario

zortrax

zortrax Inventure Manual de usuario

zortrax

zortrax M200 Plus Manual de uso y cuidado

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax M200 Manual de funcionamiento

zortrax

zortrax M200 Plus Guía

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax Z-PETG Manual de usuario

zortrax

zortrax M300 Instrucciones de uso

zortrax

zortrax Inkspire Manual de usuario

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax M300 Manual de uso y cuidado

zortrax

zortrax M200 Plus Manual de uso y cuidado

zortrax

zortrax M200 Manual de usuario

zortrax

zortrax M200 Manual de usuario

Manuales populares de Impresora 3D de otras marcas

Ultimaker

Ultimaker S5 Material Station Manual de usuario

EcubMaker

EcubMaker TOYDIY Manual de usuario

AnyCubic

AnyCubic Kossel Plus Manual de usuario

ReDeTec

ReDeTec ProtoCycler Manual de usuario

Kywoo3D

Kywoo3D Tycoon IDEX Manual de usuario

CraftBot

CraftBot PLUS PRO Manual de usuario

3DGence

3DGence INDUSTRY F340 Manual de usuario

HP

HP Jet Fusion 4200 Instrucciones de funcionamiento

Rokit

Rokit AEP Series Manual de usuario

AnkerMake

AnkerMake M5 Manual de usuario

DIYElectronics

DIYElectronics PRUSA I3 Instrucciones de montaje

Ackuretta

Ackuretta FreeShape 120 Manual de usuario

LONGER

LONGER LK5Pro Manual de usuario

Stratasys

Stratasys J850 Manual de usuario

MakerBot

MakerBot Replicator Manual de usuario

Stratasys

Stratasys FDM Vantage Series Manual de usuario

ZYYX

ZYYX Pro II Manual de usuario

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guía del usuario

Z-Axis Coupler Replacement

SOURCE:

https://support.zortrax.com/z-axis-coupler-replacement/

page 1 / 25

Table Of Content

Unplugging the Power Cable 4

Changing the Printer's Position 5

Unscrewing the Bottom Plate, part 1 6

Turning the Printer 7

Unscrewing the Bottom Plate, part 2 8

Separating the Bottom Plate 9

Providing Better Access to the Z-Axis Coupler 10

Unplugging the Z-Axis Motor Cable 11

Loosening the Z-Axis Coupler Screws 12

Unscrewing the Z-Axis Motor 13

Z-Axis Coupler Removal 14

Z-Axis Coupler Assembly 15

Z-Axis Motor Assembly 16

Tightening the Z-Axis Coupler Screws 17

Plugging the Z-Axis Motor Cable 18

Rearranging the Cables 19

Bottom Plate Installation 20

Securing the Bottom Plate, part 1 21

Turning the Printer 22

Securing the Bottom Plate, part 2 23

Changing the Printer's Position 24

Plugging the Power Cable 25

page 2 / 25

The Z-axis coupler is responsible for the platform’s movement along the Z axis.

Therefore, if the platform does not move at all or it moves with difficulties and

makes unusual noises, the Z-axis couple needs to be replaced. Before replacing

the coupler, make sure that the screws on the coupler are properly tightened.

More details can be found in the manual.

If the screws cannot be fully tightened, follow the steps from this manual to replace the Z-

axis coupler.

The following manual shows the M200 repair work. For the M300, these procedures are

the same.

page 3 / 25

Unplugging the Power Cable

Turn off the printer and unplug the power cable. Wait a few minutes for all the capacitors

to discharge.

page 4 / 25

Changing the Printer's Position

Grab the printer’s housing and change the printer’s position so that you can easily

access the bottom plate.

page 5 / 25

Unscrewing the Bottom Plate, part 1

Unscrew the screws that secure the bottom plate on one side of the housing. Use a

2.5mm Allen key.

page 6 / 25

Turning the Printer

Turn the printer over.

page 7 / 25

Unscrewing the Bottom Plate, part 2

Unscrew the screws that secure the bottom plate on the other side of the housing. Use

the same key.

page 8 / 25

Separating the Bottom Plate

Separate the bottom plate from the printer and unplug the bottom fan cable from the

motherboard.

page 9 / 25

Providing Better Access to the Z-Axis Coupler

Unfasten the two extruder cable straps and unplug the cable from the motherboard.

Next, unfasten the third strap. Place the extruder cable between the power supply unit

and the housing. Finally, grab the cables next to the motherboard and fasten the strap.

This step is not necessary to follow, however it is recommended so as to avoid the risk

of damaging the cables and to get better access to the Z-Axis coupler.

page 10 / 25