ZKTeco iFace Series Manual de usuario
iFace Series Installation Guide
Version：1.2.1
Date：Oct. 2010
About this Guide
This guide provides actual installation instructions only. For information
regarding user instructions, please refer to “iFace Series User Manual”.
iFace Series Installation Guide
I
Content
1 System Configuration........................................................................1
1.1. Notice about installing..............................................................1
1.2. Installation Environment ..........................................................3
1.3 View of operation panel.............................................................4
2 The illustration of system construction ...........................................6
2.1 The illustration of system construction......................................6
2.2 The sketch map of communication............................................7
3 Installation...........................................................................................8
3.1. Installation Steps.......................................................................8
3.2 Conect with other devices..........................................................9
3.2.1 Door sensor connection ...........................................11
3.2.2 Exit-button connection..............................................11
3.2.3 Time Ring connection...............................................12
3.2.4 Door lock connection ................................................13
3.2.5 Ethernet connection..................................................17
3.2.6 RS232 connection.....................................................18
3.2.7 RS485 connection.....................................................19
3.2.8 Wiegand Output Connection ...................................20
3.2.9 Power Connection.....................................................21
3.3 Fix the device...........................................................................22
4 Check after Installation ...................................................................23
5. Others...............................................................................................24
5.1 Reset ........................................................................................24
5.2 Anti-dismantle button ..............................................................25
5.3 U flash disk using....................................................................25
5.4 Reserve Battery........................................................................26
iFace Series Installation Guide
1
1 System Configuration
1.1. Notice about installing
This product a mass-produced product. It strictly follows to the
criteria of manufacture and inspection of China, U.S.A, and EU.
This file contains important information. It is better for you to read
it carefully prior to use. If you ignore it, the incorrect installation
may cause the unit damage. Although we could do our best to
offer you service, the neglect to the file could cause unwanted cost
for you.
1. Before installation, please make sure the power is cut off,
because it is very dangerous if the power is on. The
short-circuit of power cable may cause the core parts damage.
2. All exposed part of connection wire end can not be exceeded
5mm to prevent the bared wire accidental connection which
leads to machine break down. And also suggest using different
colour cable to connect.
3. In the place where the static is strong or in winter, please
connect the grounding firstly, in order to prevent the instant
mass static damage the machine.
4. Connect power supply with device in the last for the wiring
connection. If you find any unusual thing occur, please firstly
cut off the power, then go to examine. Keep in mind: wiring
operation under power on will lead to machine sudden damage;
we are not liable for damages and trouble due to such
iFace Series Installation Guide
2
operation.
5. After installation finish, when go to test the exit-door button,
please keep a personal in the outside, because sometimes the
accidental issue can bring on you are not able to go outside.
6. Our equipment offer an automatically function, please after the
installing finish. Run the auto-test function to confirm the installation
finish .
7. We recommend using above the 12V/3A direct-current supply
for access control device, electricity lock better to powered by
12VDC, and no more than 1.5 A electric current At this time,
the electric current of supply should be above1A than lock
power. If the parameter of lock power surpasses this scope,
please connect technical personnel. If the power had not met
above requests, it possibly causes to be unable normally to
drive the electricity lock, even damage the device.
8. Before device to be connected please read and always follow
"Quick connect Guide" closely. Because the wrong wiring will
cause the core block and sensor to burn out, insult in device to
break down, at this cause we are not liable for any damages
and trouble.
9. If the space between power adapters and device is too long,
please do not use the twisted-pair or other type ferrules for the
power wire. When the power wire is choused, you should
consider attenuation of voltage which has passed long distance
transfer.
10. Please use specialized RS485 cable and the RS232/485
converter with power to hookup the network, the bus structure
apply to connect with each device. When a long cable is used
to transfer signal, it is need to connect a matching resistance to
iFace Series Installation Guide
3
receiver, and its value is 120Ώ.
For other matters not covered in detail herein, please refer to the User
Manual, Software Instructions, and appendixes related to this
equipment.
1.2. Installation Environment
Recommended location:
NOT Recommended locations:
Install the iFace indoors at least 10
feet (3m) away from windows, and
6.5 feet (2m) away from light
fixtures. Preferable light intensity
should range between 0-800 LUX.
10Lux 1200+ Lux 0-800Lux
Direct sunlight
Outdoors Direct sunlight
thru window
Indirect sunlight
thru window
Too close to
light fixtures
iFace Series Installation Guide
4
1.3 View of operation panel
Front view
Side view
LED light
TFT touch screen
Fingerprint Sensor
Baseline
Integrated RF Card
Module Read Section
Touch Keypad
Camera
Power key
Reset key
USB
iFace Series Installation Guide
5
Back view
Battery slot
Power
TCP/IP
USB
connection terminal
Loudspeaker
iFace Series Installation Guide
6
2 The illustration of system construction
2.1 The illustration of system construction
iFace Series Installation Guide
7
PC
PC
2.2 The sketch map of communication
1 Fingerprint machine directly connects with PC through RS232 or
TCP/IP.
2 Fingerprint machine connects with PC through RS485 network.
3 Fingerprint machine connects with PC through TCP/IP network.
TCP/IP
TCP/IP
TCP/IP …
RS485 Switch
RS232 …
RS485
Switch
TCP/I
P
or RS232
PC
iFace Series Installation Guide
8
3 Installation
3.1. Installation Steps
1. Affix the paper template to the wall and drill holes within the
three marked circles on the paper template.
We recommend affixing the template about four (4) feet (1.2m)
above the ground, assuming the average height of your users is
5-6 feet tall(1.5m-1.85m).
2.Now affix the mounting plate on the wall by drilling three (3)
screws into the three (3) circles marked on the paper template.
3. After installing the back cover, ensure it will be stable, solid and
non-loosening.
Tabla de contenidos
Otros manuales de Terminal táctil de ZKTeco
ZKTeco
ZKTeco ZKBio810 Series Manual de usuario
ZKTeco
ZKTeco Green Label ProCapture-T Manual de usuario
ZKTeco
ZKTeco ZKBio710 Series Manual de usuario
ZKTeco
ZKTeco IM20 Manual de usuario
ZKTeco
ZKTeco LockerPad-7B Manual de usuario
ZKTeco
ZKTeco EFace10 Manual de usuario
ZKTeco
ZKTeco U1000F Manual de usuario
ZKTeco
ZKTeco ZKAIO4000W Manual de usuario
ZKTeco
ZKTeco FaceKiosk-H13 Manual de usuario
ZKTeco
ZKTeco ZPAD+ Manual de usuario
ZKTeco
ZKTeco G4 Manual de usuario
ZKTeco
ZKTeco G5 Manual de usuario
ZKTeco
ZKTeco MB10-VL Manual de usuario
ZKTeco
ZKTeco SpeedFace - V5L Manual de usuario
ZKTeco
ZKTeco ZK3530 Manual de usuario
ZKTeco
ZKTeco uFace Plus Series Manual de usuario
ZKTeco
ZKTeco F305 Manual de usuario
ZKTeco
ZKTeco F Series Manual de usuario
ZKTeco
ZKTeco G4 Pro Series Manual de usuario
ZKTeco
ZKTeco MB10-VL Manual de usuario
