ZKTeco SpeedFace - V5L Manual de usuario
Quick Start Guide
Version: 1.0
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.
SpeedFace - V5L
1
Overview
Flash
Camera & Palm collector
5" touchscreen
Microphone
Fingerprint sensor &
Card reading area
Reset
Speaker
RS232
RS485
485B
485A
GND
TXD
RXD
GND
TXD2
RXD2
RS232
GND
12V
+12V
GND
IWD0
IWD1
WD0
WD1
TX+
RX+
TX-
RX-
AUX
AL+
AL-
NC1
COM
NO1
BUT
GND
SEN
GND
Lock
Alarm
ExitButton
Sensor
Auxiliary
input
Ethernet
Power in
Wiegand
in
Wiegand
out
Installation Environment
Magnetic
tamper
switch
Terminal
block
INDOOR USE
Please refer to the following recommendations for installation.
AVOID DIRECT
SUNLIGHT AND EXPOSURE
KEEP DISTANCE AVOID GLASS
REFRACTION
KEEP EFFECTIVE
DISTANCE0.3-2m
10ft
6.5ft
window
2
①
②
TCP/IP
Alarm Smoke
detector
Lock
Exit button
Door sensor
Card
reader
Standalone Installation
Device Installation
① Attach the mounting template sticker to the wall, and drill holes according to
the mounting paper. Fix the back plate on the wall using wall mounting
screws.
② Attach the device to the back plate.
③ Fasten the device to the back plate with a security screw.
1 2 3
1.5m
3
Lock Relay Connection
The system supports Normally Opened Lock and Normally Closed Lock.
The NO LOCK (normally opened at power on) is connected with 'NO1' and 'COM'
terminals, and the NC LOCK (normally closed at power on) is connected with 'NC1'
and 'COM' terminals. Take NC Lock as an example below:
1)Device not sharing power with the lock 2)Device sharing power with the lock
Normally Closed Lock
FR107
AUX
GND
SEN
GND
BUT
NO1
COM
NC1
AL+
AL-
+12V
GND
DC12V
+12V
GND
FR107
AUX
GND
SEN
GND
BUT
NO1
COM
NC1
AL+
AL-
DC12V
Normally Closed Lock
DC12V
Door Sensor, Exit Button & Alarm Connection
AUX
GND
SEN
GND
BUT
NO1
COM
NC1
AL+
AL-
Door Sensor
ExitButton
Alarm's power switch
Alarm
SmokeDetector
TXD
RXD
GND
RS232
Reader
485+
485-
GND
RXD
GND
TXD
RS232
Reader
RS485
Reader
RXD2
TXD2
GND
RXD
TXD
GND
485A
485B
RS485 and RS232 Connection
Wiegand Reader Connection
Wiegand Reader
Access controller
+12V
IWD1
IWD0
GND
WD1
WD0
4
Power Connection
12V DC
GND
GND
12V
Recommended power supply
1. 12V ± 10%, at least 3000mA.
2. To share the power with other devices, use a power supply with higher
current ratings.
Ethernet Connection
Default IP address: 192.168.1.201
Subnet mask: 255.255.255.0
Click [COMM.] > [Ethernet] > [IP Address] , input the IP address and click [OK].
Note: In LAN, IP addresses of the server (PC) and the device must be in the
same network segment when connecting to ZKBioSecurity software.
8
7
6RJ 45
5
4
3
2
1
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
TX+
TX-
RX+
RX-
5
ZKBioSecurity
Main Menu
User Mgt. User Role COMM. System
Data Mgt.Personalize Attendance
Search
Autotest System Info
Access Control
L
User Registration
Clickon> [User Mgt.] > [New User] to register a new user. Settings include
entering user ID and name, registering fingerprint, face, password and user photo,
setting user role.
When there is no super administrator set in the device, click on to enter the menu.
After setting the super administrator, the system will request for the administrator’s
verification before entering the menu. For the security purpose, it is recommended to
register a super administrator at the first time you use the device.
User Mgt.
New User
All Users
Display Style
Enroll Face
Enrolled Successfully
1
1
1
*****
1
New User
User ID
Name
User Role
Fingerprint
Face
Password
User Photo
Access Control Role
Normal User
Mike
L
6
Main Menu
User Mgt. User Role COMM. System
Data Mgt.Personalize Attendance
Search
Autotest System Info
Access Control
L
Access Control Options
Time Rule setting
Holidays
Combined Verification
Anti-passback Setup
Duress Options
Access Control
Password/Face/Palm
1
Gate Control Mode
Verification Mode
Door available time period
Normal open time period
Master Device
Auxiliary input configuration
Speaker Alarm
Reset Access Setting
Access Control Options
None
In
Access Control Settings
Clickon to enter the access control management interface > [Access Control]
and set relevant parameters of access control.
Main Menu
User Mgt. User Role COMM. System
Data Mgt.Personalize Attendance
Search
Autotest System Info
Access Control
L
Ethernet Settings
Clickon > [COMM.] > [Ethernet]to set the network parameters. If the TCP/IP com-
munication of the device is successful, the icon will be displayed in the upper right
corner of the standby interface.
Ethernet
PC Connection
Cloud Server Setting
Wiegand Setup
Network Diagnosis
Comm.
7
192.168.163.201
114.114.114.114
4970
255.255.255.0
192.168.163.1
IP Address
Subnet Mask
Gateway
DNS
TCP COMM. Port
DHCP
Display in Status Bar
Ethernet
8
LAN Video Intercom Function Settings
1. Choose the "Video-VMS" module of the ZKBioSecurity software to install.
(The Video module and the Video-VMS module cannot be installed together.)
2. Install the ZKBio VMS Plugin.
(To recognize the intercom function, the ZKBioSecurity software and the ZKBio VMS
Plugin must be opened simultaneously.)
Step 1: Install the ZKBioSecurity software and ZKBio VMS Plugin
Configuration Parameters
Step 2:
1. Add site on the Video-VMS Plugin
a. Click [Choose site] > [Site management] > [Add] on the login interface, enter the
Name, IP address, and port to add a site.
IP Address: Enter the local IP address.
Port: The default port number is 5252.
b. Login to the Video-VMS plugin after adding the site. The user name and the initial
password are both “admin”.
(When the Video-VMS plugin is connected successfully to the ZKBioSecurity, the
password changes to the admin user password of the ZKBioSecurity.)
2. Configure the connection path of the ZKBioSecurity and VMS plugin
Click [Video] > [Connection] > [Connection Management] to change the path, as
shown in the following figure.
VMS Connection Path: , Port: 8489 by default.“http://local IP address: port"
(eg., http://192.168.163.61:8489).
Server Path: . The port is the service port set during “http://server IP address: port”
installation (not the ADMS port) (eg., http://192.168.163.61:8098).
3. Configure the parameters on the device
a. Click on > [COMM.] > [Cloud Server Setting] to set the server address and server
port, that is, the IP address and port number of the server after the software is
installed. The icon is displayed in the upper right corner of the standby interface
when the device communicates with the server successfully.
b. Click on > [System] > [Video intercom parameters] > [Intercom Server Setting]
to set the server address and server port.
Server Address: Enter the ZKBioSecurity installation IP address.
Server Port: It is the service port set during installation (not the ADMS port).
Main Menu
User Mgt. User Role COMM. System
Data Mgt.Personalize Attendance
Search
Autotest System Info
Access Control
L
ADMS
8088
192.168.163.61
Server mode
Enable Domain Name
Server Address
Server port
Enable Proxy Server
Cloud Server Setting
8098
192.168.163.61
Server Address
Server port
Intercom Server Setting
9
Tabla de contenidos
Otros manuales de Terminal táctil de ZKTeco
ZKTeco
ZKTeco LPRS2000 Manual de usuario
ZKTeco
ZKTeco ZKBio710 Series Manual de usuario
ZKTeco
ZKTeco ZKAIO4000W Manual de usuario
ZKTeco
ZKTeco S922 Series Manual de usuario
ZKTeco
ZKTeco Green Label ProCapture-T Manual de usuario
ZKTeco
ZKTeco ma 300 Manual de usuario
ZKTeco
ZKTeco ZKAIO1000W Manual de usuario
ZKTeco
ZKTeco F Series Manual de usuario
ZKTeco
ZKTeco ZKBio930 Manual de usuario
ZKTeco
ZKTeco ProBio(QR) Manual de usuario
ZKTeco
ZKTeco MB20-VL Manual de usuario
ZKTeco
ZKTeco uFace Plus Series Manual de usuario
ZKTeco
ZKTeco G2 Manual de usuario
ZKTeco
ZKTeco FA2000 Manual de usuario
ZKTeco
ZKTeco D3 Series Manual de usuario
ZKTeco
ZKTeco VT07-C22L Manual de usuario
ZKTeco
ZKTeco iFace Series Manual de usuario
ZKTeco
ZKTeco F305 Manual de usuario
ZKTeco
ZKTeco U1000F Manual de usuario
ZKTeco
ZKTeco MB10-VL Manual de usuario
