ZKTeco G5 Manual de usuario
QUICK START GUIDE
Applicable Model: G5
Version: 1.0
Date: May 2023
Outdoor & Multi-Biometric
Access Control Terminal
Safety Precautions
Before installation, please read the following precautions carefully to prevent
the risks of danger to the users of this product or those nearby and damaging
the device.
Do not expose to direct sunlight, water, dust and soot.
Do not place any magnetic objects near the product. Magnetic objects
such as magnets, CRT, TV, monitors or speakers may damage the device.
Do not place the device next to heating equipment.
Prevent water, drinks or chemicals leaking into the device.
This product is not intended for use by children unless they are
supervised.
Do not drop or damage the device.
Do not disassemble, repair or modify the device.
Do not use the device for any purpose other than those specified.
Remove dusts or dirts regularly. While cleaning, wipe dust off with a
smooth cloth or towel instead of water.
Contact your supplier in case of any problem!
1
2
Device Overview
Visible Light Camera
Near-infrared Camera
Near-infrared Flash
8" HD Capacitive Touch Screen
Microphone
Fingerprint Scanner
Built-in ID Card Reader
Speaker
USB Port
Micro USB
Back Plate
Terminal Block
11.004" (279.5mm)
5.551" (141.0mm)
1.142" (29.0mm)
3
Terminal Block
AUXIN
SEN
BUT
GND
NO
COM1
NC1
ALARM-
ALARM+
12V OUT
GND
485B
485A
232TXD
232RXD
WD0
WD1
IWD0
IWD1
BELL+
BELL-
Auxiliary Input
Sensor
Exit Button
Alarm
Power Out
Power In
RS485
RS232
Lock
Wiegand Out
Wiegand In
Bell
USB
Ethernet
4
Product Installation
The recommended distance
Installation on the wall
First passing the wires through the wiring hole in the back plate.
Drill holes at suitable locations on the wall, then fix the back plate to the wall with mounting screws,
the recommended distance from the camera to the ground is 61.024 (1.55m). inches
Then attach the device to the back plate from top to bottom.
Fasten the device to the back plate with a security screw.
1 2
43
For users whose height is between 55.118" to 70.866" (1.4m to 1.8m), the
recommended height of the equipment is 61.024" (1.55m), and the
distance from the personnel to the equipment is 19.685" (0.5m). Users not
in the range can adjust the position by moving back and forth according
to the actual situation.
61.024" (1.55m)
19.685" (0.5m)
①
②
③
④
1
2
5
Ethernet Connection
Recommended power supply
Power & Ethernet Connection
Power Connection
Recommended AC adapter 12V 3A:,
AC adapterTo share the power with other devices, use an with higher current ratings.
AC Adapter
RouterNetwork Cable
6
Access Control & Reader Connection
Access Control Connection
Reader Connection
12V OUT
GND
485B
485A
232TXD
232RXD
WD0
WD1
IWD0
IWD1
+12V
GND
485-
485+
+12V
GND
RXD
TXD
RS485 Reader
RS232 Reader
Wiegand Reader
+12V
GND
WD0
WD1
12V OUT
GND
485B
485A
232TXD
232RXD
WD0
WD1
IWD0
IWD1
WD0
WD1
GND
GND
+12V
Access
Controller
Do not use
Do not use
7
Lock Relay Connection
Device not sharing power with the lock is shown below:
DC12V, 3A
AC Adapter
NC
COM
NO
V- V+
FR107
Magnetic Lock
DO NOT REVERSE
THE CONNECTION.
+12V
GND
AUXIN
SEN
BUT
GND
NO
COM1
NC1
ALARM-
ALARM+
+12V DC
Device sharing power with the lock is shown below:
DC12V, 3A
AC Adapter
NC
COM
NO
V- V+
FR107
Magnetic Lock
DO NOT REVERSE
THE CONNECTION.
+12V
GND
AUXIN
SEN
BUT
GND
NO
COM1
NC1
ALARM-
ALARM+
The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (Normally Opened
when powered) is connected with 'NO' and 'COM' terminals, and the NC Lock (Normally Closed when powered)
is connected with 'NC' and 'COM' terminals. The power can be shared with the lock or can be used separately for
the lock, as shown in the example with NC Lock below:
Do not use
Do not use
8
Bell Connection
BELL+
BELL-
Door Bell
Smoke Detector, Door Sensor, Exit Button & Alarm Connection
NO
COM
+12V DC
Alarm
Detector Power
Smoke Detector
Exit Button
+12V DC
Alarm Power
+12V DC
Bell Power
AUXIN
SEN
BUT
GND
NO
COM1
NC1
ALARM-
ALARM+
Door Sensor
Connecting Other Devices
Do not use
Standalone Installation
WAN
PC
Option A Option B
TCP/IP
3G
PC
SWITCH
Door Sensor
Exit Button
Lock
Alarm
9
Smoke Detector
Door Bell
USB Disk
Tabla de contenidos
Otros manuales de Terminal táctil de ZKTeco
ZKTeco
ZKTeco TF1700 Manual de usuario
ZKTeco
ZKTeco ZKBio910 Manual de usuario
ZKTeco
ZKTeco PA22 Manual de usuario
ZKTeco
ZKTeco IM20 Manual de usuario
ZKTeco
ZKTeco ZKBio930 Manual de usuario
ZKTeco
ZKTeco S922 Series Manual de usuario
ZKTeco
ZKTeco EFace10 Manual de usuario
ZKTeco
ZKTeco ZPAD+ Manual de usuario
ZKTeco
ZKTeco LPRS2000 Manual de usuario
ZKTeco
ZKTeco D1s Manual de usuario
ZKTeco
ZKTeco LockerPad-7B Manual de usuario
ZKTeco
ZKTeco ZK3530 Manual de usuario
ZKTeco
ZKTeco SpeedFace V4LTI Manual de usuario
ZKTeco
ZKTeco G4 Manual de usuario
ZKTeco
ZKTeco ma 300 Manual de usuario
ZKTeco
ZKTeco LFace10 Manual de usuario
ZKTeco
ZKTeco RevFace15 Manual de usuario
ZKTeco
ZKTeco D3 Series Manual de usuario
ZKTeco
ZKTeco iClock 885 Manual de usuario
ZKTeco
ZKTeco ProBio(QR) Manual de usuario
