ZKTeco U1000F Manual de usuario
Installation Guide
UHF RFID Standalone Terminal:
U1000E,U1000F, U2000E, U2000F
Version: 1.0
Date: 2017.09
1
1. Overview
Front View
Lateral View and Interface
Cable Definition:
Dimension
250mm*250mm*70mm (U1000E, U1000F)
445mm*445mm*70mm (U2000E, U2000F)
Antenna
Working Frequency:
902MHz 926MHz
865MHz 868MHz
Read Range:
U1000E/F (0-6 meters)
U2000E/F (0-12 meters)
Mounting
Bracket
Cables
RJ45
USB
2PIN
4PIN Green
6PIN Green
Cables
6PIN Green
6PIN Black
4PIN Green
4PIN Black
4PIN Black
6PIN Black
2
2.Install the Integrated Machine
1) Hang Mounting
Please install the integrated machine according to the following chart. The
machine is installed on the fixed column, and the angle and height is adjusted
according to the actual effect of swing card.
Method A:
Method B:
Note: To get better reading performance, driving direction of vehicle should
face to the UHF integrated machine.
2) Ceiling Mounting
Please install the integrated machine vertically on the ceiling. We recommend
the installation height from the ground is no more than 4 meters in order to
better identify effect.
3
Note:
1)Avoid installing the integrated machine against to another.
2) The integrated machine detection distance may vary depending on rain,
snow or wind.
3) The device should be away from strong magnetic field when working.
3. Install the UHF Card
1) Tag1, DF01Card, DF02Card
UHF1-Tag1, DF01Card and DF02 Card are generally used in long distance access
control management and long distance pedestrian crossing control
management.
4
2) Tag2 Card
UHF1-Tag2 is generally used in long distance pedestrian crossing control
management, such as long distance single channel access management in
construction site.
3) Tag3 Card
UHF1-Tag3 is generally used in long distance fixed vehicle access management.
It is installed on the upper or lower edges of the license plate.
As is shown below:
4) Tag4 Card
UHF1-Tag4 is also generally used in long distance fixed vehicle access
management. It is pasted on the interior windshield of car.
The distance between the UHF tag and the metal frame shall be 80 mm at least.
5
The position of the tag/card in the vehicle is as follows:
Note: If there is a metal
explosion-proof film above the
windshield, you have to cut a
small piece off it or roll down
the window to read the tag.
(The cut area is at least one
time the tag’s)
4. Structure Function
UHF Tag
6
(1)If a registered user verified, the device will export the signal to unlock the
door.
(2)Door sensor will detect the on-off state.
(3) External exit button is supported; it is convenient to open the door inside.
(4) External card reader is supported.
(5) Connect the USB port of the integrated machine to the USB port of the
computer to set the working parameters of the integrated machine.
(6)Supports TCP/IP modes to connect with PC.
5. Lock Connection
1) Shares power with the lock:
ULOCK=12V, I ≥ IDevice + ILock (The maximum operating current of device is 100mA,
and the rated current is 60mA); and the lock is near to the device.
2) Does not share power with the lock:
When ULOCK=12V, I < IDevice + ILock (The maximum operating current of device is
100mA, and the rated current is 60mA);
When ULOCK≠12V;
When the lock is far from the device.
7
(1) The system supports NO LOCK and NC LOCK. The NO LOCK (normally open
by power on) is connected with NO terminal, and the NC LOCK is connected
with NC terminal.
(2) To prevent the generation of self-inductance EMF which would affect the
system, when the electrical lock is linked to the Access Control System, it is
required to connect one FR107 diode (equipped in the package, do not reverse
the polarities) in parallel in order to release the self-inductance EMF.
6. Barrier Connection
7. Connected with other parts
8
8. Connected with Power
9. Wiegand Output & Input
1) Wiegand Output
2) Wiegand Input
Note:
(1) Please keep the distance between the device and Access Control or Card
Reader less than 90 meters (Please use Wiegand signal extender in long
distance or interference environment).
(2) To keep the stability of Wiegand signal, connect the device and the Access
Control or Card Reader in same ‘GND’ in any case.
Input DC12V, ≤110mA (≤80mA
standby)
Positive is connected with +12V,
negative is connected with GND
(do not reverse the polarities).
The device supports standard
Wiegand 26/34 output, as a
reader device it has a very
good compatibility.
The device has the function of
Wiegand signal input. It
supports to connect with an
independent card reader.
They are installed each side of
the door, to control the lock
and access together.
9
10. Connected with Computer
1) USB Connection
Connect the USB port of the integrated machine to the USB port of the
computer. Set the working parameters of the integrated machine using DEMO
software.
2)RJ45 Connection
Connect the RJ45 port of the integrated machine to the Ethernet port of the
computer. The machine supports access to ZKAccess 3.5 and ZKBioSecurity 3.0.
Integrated Machine
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Terminal táctil de ZKTeco
ZKTeco
ZKTeco MB20-VL Manual de usuario
ZKTeco
ZKTeco G4 Pro Series Manual de usuario
ZKTeco
ZKTeco ZK75 Series Manual de usuario
ZKTeco
ZKTeco RevFace15 Manual de usuario
ZKTeco
ZKTeco LPRS2000 Manual de usuario
ZKTeco
ZKTeco LPRS2000 Manual de usuario
ZKTeco
ZKTeco F Series Manual de usuario
ZKTeco
ZKTeco S922 Series Manual de usuario
ZKTeco
ZKTeco ZK3530 Manual de usuario
ZKTeco
ZKTeco D1s Manual de usuario
ZKTeco
ZKTeco ZKBio810 Series Manual de usuario
ZKTeco
ZKTeco ProBio(QR) Manual de usuario
ZKTeco
ZKTeco F305 Manual de usuario
ZKTeco
ZKTeco VT07-C22L Manual de usuario
ZKTeco
ZKTeco MB10-VL Manual de usuario
ZKTeco
ZKTeco G4 Manual de usuario
ZKTeco
ZKTeco SpeedFace V4LTI Manual de usuario
ZKTeco
ZKTeco SpeedFace M4 Manual de usuario
ZKTeco
ZKTeco iClock 885 Manual de usuario
ZKTeco
ZKTeco LockerPad-7B Manual de usuario
