Wilson Electronics Weboost AM100-PRO Manual de usuario

Installation Guide

AM100-Pro

Vehicle Cell Signal

Booster Kit

Index

Package Contents ........................................................... 1

STEP 1 Mount the Outside Antenna ............................................ 2

STEP 2 Mount the Inside Antenna ............................................. 4

STEP 3 Connect Outside Antenna to Booster ................................... 5

STEP 4 Connect Inside Antenna to Booster ..................................... 5

STEP 5 Connect Power Supply to Booster ...................................... 6

Booster Light Patterns ....................................................... 7

Troubleshooting ............................................................. 9

Safety Guidelines ............................................................ 11

Speciﬁcations .............................................................. 12

Warranty................................................................... 13

Package Contents

Booster &

Mounting

Bracket

Outside

Antenna

(311216)

Inside

Antenna

(314401)

Power

Cable

(850029)

Identify a location on the top of your vehicle

that is:

■ Near the center of the roof.

■ At least 12 inches away from any other

antennas.

■ At least 12 inches away from any

windows (for best performance install

on top of vehicle).

Clean the surface where you will place the

outside antenna. Mount the outside antenna

by placing on top of vehicle.

Note: The cable is strong enough that it may

be routed under weather stripping and shut in

most vehicle doors.

STEP 1 Mount the Outside

Antenna

12 in. away from windows

(including sunroofs)

(STEP 1 cont.)

Car/Sedan: Cable routed into rear

side door.

SUV/Van/Hatchback: Cable routed into

top of hatchback door.

Truck: Cable routed into side door.

See options on how cable can be routed with dierent vehicles.

Note: When going though a car wash, remember to remove your antenna.

Identify a place to mount the in-vehicle

antenna, either on the side of the seat or on

the dash and mount. The location should

be at least 18 inches but no more than 36

inches from where the cellular device will

be used. Use the Velcro® adhesive strip/

adhesive strip provided and attach to

desired location.

STEP 2 Mount the Inside Antenna

seat mounting

option

dash mounting

option

In-Vehicle

Antenna

Velcro®strip

Connect the cable from the outside antenna

to the port labeled “Outside Antenna” on

the AM100-Pro booster.

Note: The Velcro® strip on the bottom of the

booster can also be used to keep booster

from sliding around.

STEP 3 Connect Outside

Antenna to Booster

from Outside Antenna

Connect the cable from the inside antenna

to the port labeled “Inside Antenna” on the

booster.

STEP 4 Connect Inside Antenna

to Booster

from Inside Antenna

Connect the 12V power supply cord to the end

of the booster, labeled "12V DC" then plug the

power adapter into vehicle’s 12V DC power

supply. Push switch to ON position. If your

AM100-Pro is working correctly, the light on

the booster will be green. Use only the power

supply provided in this package.

Note: If the 12V Cigarette Lighter port on your

car is always on (even when your vehicle

is turned o) and you will be parking for

extended periods of time (more than a day),

we recommend you turn the booster o by

pushing power cord switch to OFF position.

This will prevent the AM100-Pro from draining

the battery in your vehicle.

Note: When going through car wash, remember

to remove your outside antenna.

STEP 5 Connect Power Supply

to Booster

connect Power

Supply Cord

plug into vehicle’s 12V DC

Power Supply

SOLID GREEN

This indicates that your AM100-Pro booster is functioning properly and there are no

issues with installation.

SOLID RED

Booster has shuto. This is due to a feedback loop condition called oscillation. This is

a built in safety feature that causes a band to shut o to prevent harmful interference

with a nearby cell tower. Refer to Troubleshooting section.

BLINKING RED, THEN SOLID GREEN

This indicates that one or more of the Booster bands has reduced power due to a

minor feedback loop condition called oscillation. This is a built in safety feature to

prevent harmful interference with a nearby cell tower. If you are already experiencing

the desired signal boost, then no further adjustments are necessary. If you are not

experiencing the desired boost in coverage then refer to the Troubleshooting section.

LIGHT OFF

If the AM100-Pro booster’s light is o, verify your power supply has power.

Booster Light Patterns

(Booster Light Patterns cont.)

NOTE: The AM100-Pro booster can be reset by disconnecting and reconnecting

the power supply.

After troubleshooting you must initiate a new power cycle by disconnecting and then

reconnecting power to the booster.

Otros manuales para Weboost AM100-PRO

Tabla de contenidos

Otros manuales de Extensor de Wilson Electronics

Wilson Electronics

Wilson Electronics weboost AH100-PRO Manual de usuario

Wilson Electronics

Wilson Electronics AG Pro 75 Manual de usuario

Wilson Electronics

Wilson Electronics AG Pro Quint 461104 Manual de usuario

Wilson Electronics

Wilson Electronics weboost DRIVE REACH Manual de usuario

Wilson Electronics

Wilson Electronics WilsonPro A1000 Manual de usuario

Wilson Electronics

Wilson Electronics WEBOOST DRIVE X OTR Manual de usuario

Wilson Electronics

Wilson Electronics AG Pro Quint Manual de usuario

Wilson Electronics

Wilson Electronics Tri-Band 4G-A Manual de usuario

Wilson Electronics

Wilson Electronics weBoost DRIVE X Manual de usuario

Wilson Electronics

Wilson Electronics weBoost DRIVE 4G-X 470510R Manual de usuario

Wilson Electronics

Wilson Electronics 460054 Manual de usuario

Wilson Electronics

Wilson Electronics Tri-Band 4G-V Manual de usuario

Wilson Electronics

Wilson Electronics weBoost DRIVE SLEEK Manual de usuario

Wilson Electronics

Wilson Electronics AG Pro 75 Manual de usuario

Wilson Electronics

Wilson Electronics weboost Office 100 Manual de usuario

Wilson Electronics

Wilson Electronics WilsonPro Single Room Manual de usuario

Wilson Electronics

Wilson Electronics WILSON PRO 4000R Manual de usuario

Wilson Electronics

Wilson Electronics MobileMaxx 3G 460011 Manual de usuario

Wilson Electronics

Wilson Electronics 271265 Manual de usuario

Wilson Electronics

Wilson Electronics DB Pro 462105 Manual de usuario

Wilson Electronics

Wilson Electronics weboost Office 200 Manual de usuario

Wilson Electronics

Wilson Electronics Sleek 4G Manual de usuario

Wilson Electronics

Wilson Electronics weboost Home Complete 530045 Manual de usuario

Wilson Electronics

Wilson Electronics Sleek 4G Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario