Robe Anolis Ambiane XP56 Manual de usuario

Version

QR code for user manual

Ambiane XP56 Recessed US

Table of contents

1. Attention ..................................................................................................................................................................... 3

2. Installation .................................................................................................................................................................. 4

2.1. DMX and DALI address setting and control ......................................................................................................... 7

2.2 0-10V control ........................................................................................................................................................ 8

3. RDM ............................................................................................................................................................................ 8

4. Optional accessories installation .............................................................................................................................. 10

4.1 Top frame installation ......................................................................................................................................... 10

4.2 Louver installation .............................................................................................................................................. 11

4.3 False ceiling mounting adaptor istallation .......................................................................................................... 12

5. DMX protocols .......................................................................................................................................................... 13

6. Technical specifications ............................................................................................................................................ 15

7. Cleaning and maintenance ....................................................................................................................................... 22

7.1 Software update ................................................................................................................................................. 22

7.2 Disposing of the product .................................................................................................................................... 23

Ambiane XP56 Recessed US

1. Attention

The unit must be installed by a qualified electrician in accordance with all national and local electrical and

construction codes and regulations.

The unit was designed for indoor use only.

Do not install the unit near highly inflammable liquids or materials.

Do not allow anything to rest on the unit.

Do not install the unit near an open flame.

Do not install the unit in dirty, dusty or badly ventilated location.

The unit has to be grounded.

A ceiling (structure) intended for installation of the unit(s) must safely hold at least 5 times the weight of the unit(s)

fastened on it.

Sufficient air accessing to the housing of the unit has to be ensured, there must not be any heat or anti-noise

insulation within a 1m x 1m area around the unit (non-IC rated fixture).

Avoid looking directly into the light beam at close range!

Suitable for fastening on Unsuitable for covering by heat insulation

non-flammable surfaces only material

Immunity of the equipment is designed for electromagnetic environments E1, E2, E3 according to the standard

EN55103-2 ed.2 Electromagnetic compatibility. Product family standard for audio, video, audiovisual and

entertainment lighting control apparatus for professional use. Part 2: Immunity.

The equipment (covers and cables) must not be exposed to a high frequency electromagnetic field higher than

3V/m.

The installation company should check levels of possible interferences above the tested levels E1,E2,E3 given by

this standard (e.g. transmitters in surrounding area) before installing the equipment.

Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility

of multimedia equipment – Emission Requirements according to class B.

Ambiane XP56 Recessed US

2. Installation

Always switch off power supply of the unit before connecting or disconnecting the unit

1. Prepare a circular opening (diameter of 186mm) in the lower ceiling (1) as shown on the picture below.

If you will use the Louver for Ambiane XP Recessed, this circular opening in the lower ceiling has to be of

diameter of 190mm.

If you will use the Top frame for Ambiane XP Recessed, this circular opening in the lower ceiling has to be of

diameter of 215mm.

Important: The Top frame for Ambiane XP Recessed has to be under lower ceiling before its inserting on

the housing of the Ambiane XP56 Recessed.

2. The yoke (2) with three holes serves for fastening the Ambiane XP56 Recessed to the ceiling (construction).

To move the yoke (2) up/down, release both screws (3), (4) on each side of the unit.

To tilt the yoke in range of +/-90° from the vertical axis, release the screw (3) on each side of the unit

Use the Allen key (size 5) to release/tighten screws (3) and (4).

The Ambiane XP56 RECESSED has to be secured to the ceiling (construction) via a safety wire pulled through

the mounting lug (5) which serves for securing of the Ambiane XP 56 Recessed to the ceiling (construction) .

Ambiane XP56 Recessed US

3. Connect cables with installed connectors to the Ambiane XP56 Recessed.

If you need access to the control PCB RB3729 (8), unscrew the four screws (7) on the cover (6).

The aperture (9) in the cover (6) allows you access to DIP switch.

The control PCB (RB3729)

Trimmer for light intensity

setting (for Secondary Power only)

The primary power input serves for a standard power (e.g. Ambiane Power XP).

The secondary power input serves for a backup power (in case that primary power failed).

If both power inputs are under voltage, the primary power has a priority and the secondary power is disabled. In

case of primary power loss, the secondary power is enabled.

The green LED on the PCB signals way of DMX address setting:

LED lights-DMX address is set by means of the DIP switch.

LED does not light- DMX address is set by means of RDM.

Ambiane XP56 Recessed US

If the fixture is supplied via the secondary power, the light output of the fixture is a white colour 3200K (RGBW, TW

version) and its light intensity can be set by a trimmer.

The fixture can be controlled by one of the following methods: DMX 512

DALI

0-10V (for PW or TD version only)

The fixture is equipped with two DMX and DALI connection blocks for easy connection to DMX or DALI chain

(In/Out method).

Primary power connection

Connector

Vcc

Function

Power +

Power

Secondary power connection

DMX connection

Connector

D+

Function

Data +

Data

Data ground

(shielding)

0-10V connection

Connector

D+

Function

+10V

DMX connectors are used for 0-10V control

Max. length of the supply cable between the Ambiane XP56 Recessed and the Ambiane Power XP and Ambiane

Power Rack is defined by the following table:

Circular cross

section of wire

Max. cable length

0.5 mm

15 m

1 mm

30 m

1.5 mm

45 m

2 mm

60 m

2.5 mm

75 m

Connector

Vcc

Function

Power +

Power

Ambiane XP56 Recessed US

2.1. DMX and DALI address setting and control

The DIP switch on the control PCB (RB3729) allows you to set DMX address and run a test light.

DIP 10 - if it is switched to ON=test light (the fixture lights at 3200K (for RGBW and TW version))

DIP 11 - has to be switched to OFF position to receive DMX 512 and DALI, position ON=0-10V control

Note: If DIP 11=OFF (fixture is controlled by DMX and DALI), the last coming command switches the fixture to the

corresponding operation mode (DMX operation by a DMX command, DALI operation by a DALI command). E.g. the

fixture stays in a DALI operation and last coming command is a DMX command which switches the fixture to DMX

operation. Next command is a DALI command and switches the fixture to the DALI operation etc.

If you need the permanent DALI operation, you have to send a DALI command 8 to the fixture.

DMX control

The DMX start address, is the first channel used to receive instructions from the DMX controller. The address may

be any channel from 1 to 512. DMX address can be set either by DIP switch or by RDM. DMX address set by RDM

overwrites address set by DIP switch and vice versa. The green LED on PCB signals way of DMX address setting:

LED lights-DMX address is set by means of the DIP switch.

LED does not light-DMX address is set by means of RDM.

The DIP 11 has to be set to OFF position.

Example of DMX addresses:

Ambiane XP56 Recessed US

DALI control

Addressing of the fixture has to be made by means of an external DALI controller.

If you need to start the permanent DALI control of the fixture (fixture will not respond to DMX commands), the

external DALI controller has to send activating command (8=ON).

If you need to stop the permanent DALI control of the fixture, the external DALI controller has to send deactivating

command (0=OFF).

2.2 0-10V control

DIP 11 has to be set in ON position. 0-10V operation has priority to DALI and DMX commands. The option is

applicable for the PW and TD version of the Ambiane XP56 Recessed only.

3. RDM

This fixture supports RDM operation. RDM (Remote Device Management) is a bi-directional communication

protocol for use in DMX 512 control systems, it is the new open standard for DMX512 device configuration and

status monitoring.

RDM allows you to set a DMX address, select DMX mode, readout software version of the fixture etc. It is also used

for fixture software update by means of the Robe Uploader.

RDM model ID for the Ambiane XP56 Recessed is 0x0109.

Parameter ID

Discovery

command

SET command

GET command

DISC_UNIQUE_BRANCH

DISC_MUTE

DISC_UN_MUTE

DEVICE_INFO

SUPPORTED_PARAMETERS

SOFTWARE_VERSION_LABEL

DMX_START_ADDRESS

* *

IDENTIFY_DEVICE

* *

DEVICE_MODEL_DESCRIPTION

MANUFACTURER_LABEL

DEVICE_LABEL

* *

DMX_PERSONALITY

* *

DMX_PERSONALITY_DESCRIPTION

RESET_DEVICE

SENSOR_VALUE

SENSOR_DEFINITION

Ambiane XP56 Recessed US

SLOT_INFO

SLOT_DESCRIPTION

DEFAULT_SLOT_VALUE

PARAMETER_DESCRIPTION

Ambiane XP56 Recessed US

4. Optional accessories installation

4.1 Top frame installation

The Top frame for Ambiane XP56 Recessed (2) serves for covering of the opening in the lower ceiling (1) if it is

required.

Note: The Top frame has to be placed under lower ceiling before sliding it onto the housing of the Ambiane XP56

Recessed.

1. Slide the Top frame (2) onto the housing of the Ambiane XP56 Recessed through the opening in the lower

ceiling.

2. Secure the Top frame in a right position by means of two spring locks (3) which have to lean against ceiling (1).

Otros manuales para Anolis Ambiane XP56

Tabla de contenidos

Otros manuales de Equipo de iluminación de Robe

Robe

Robe ANOLiS ArcSource Submersible II Manual de usuario

Robe

Robe Esprite Fresnel Manual de usuario

Robe

Robe Anolis ArcSource Outdoor 24 MC Integral RGBW Manual de usuario

Robe

Robe PATT 2013 Manual de usuario

Robe

Robe Robin MMX Blade Manual de usuario

Robe

Robe ClubScan 150CT Manual de usuario

Robe

Robe Robin 300E Spot Manual de usuario

Robe

Robe Color Spot250AT Manual de usuario

Robe

Robe ROBIN iPointe65 Manual de usuario

Robe

Robe Stage Banner 10 AT Series Manual de usuario

Robe

Robe Anolis Eminere Inground 2 Wireless DMX Manual de usuario

Robe

Robe ClubWash 250CT Manual de usuario

Robe

Robe DMX Control 512 Manual de usuario

Robe

Robe ANOLiS Eminere Remote UV 2 Manual de usuario

Robe

Robe Anolis Calumma S MC Manual de usuario

Robe

Robe COLORSPOT 170 AT Manual de usuario

Robe

Robe CLUBSPOT 160 CT Manual de usuario

Robe

Robe Robin 300 plasma spot Manual de usuario

Robe

Robe ColorWash 250 AT Manual de usuario

Robe

Robe PATT 2017 Manual de usuario

Robe

Robe Color Wasf 1200E Manual de usuario

Robe

Robe Anolis Eminere 1 Manual de usuario

Robe

Robe Anolis Ambiane XP56 Manual de usuario

Robe

Robe Robin 100 LEDBeam Wireless DMX CRMX Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario