Robe Esprite Fresnel Manual de usuario

Version 2.4

QR code for user manual

Table of contents

1. Safety instructions ......................................................................................................... 3

2. Operating determination................................................................................................ 4

3. Fixture exterior view ...................................................................................................... 6

4. Installation....................................................................................................................... 7

4.1 Connection to the mains ............................................................................................ 7

4.2 Replacing frost .......................................................................................................... 7

4.3 Installing the top hat .................................................................................................. 8

4.4 Installing the module of Fresnel lens (module of PC lens)......................................... 8

4.5 Rigging the xture ...................................................................................................... 9

4.6 DMX-512 connection................................................................................................ 11

4.7 Ethernet connection ................................................................................................. 12

4.8 Wireless DMX operation .......................................................................................... 14

5. Remotely controllable functions................................................................................. 15

6. Control menu map........................................................................................................ 17

7. Control menu ............................................................................................................... 21

7.1 Tab " Address" .......................................................................................................... 22

7.2 Tab "Information" ...................................................................................................... 23

7.3 Tab "Personality" ...................................................................................................... 26

7.4 Tab "Manual Control"................................................................................................ 27

7.5 Tab "Stand-alone" .................................................................................................... 28

7.6 Tab "Service" ............................................................................................................ 29

8. RDM ............................................................................................................................... 32

9. Error and information messages ................................................................................ 33

10. Robe Ethernet Access Portal (REAP)....................................................................... 36

11. Technical Specications ............................................................................................ 37

12. Maintenance and cleaning......................................................................................... 47

12.1 Disposing of the product ........................................................................................ 48

13. ChangeLog ................................................................................................................. 48

14. Appendix .................................................................................................................... 49

14.1Changing the LED light source ............................................................................. 49

14.2. Obtaining information about the LED light source by mobile phone ................... 53

Esprite Fresnel

Esprite PC

CAUTION!

Keep this device away from rain and moisture!

Unplug mains lead before opening the housing!

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOU INITIAL START - UP!

1. Safety instructions

Every person involved with installation and maintenance of this device have to:

- be qualied

- follow the instructions of this manual

CAUTION!

Be careful with your operations.

With a high voltage you can suer

a dangerous electric shock when touching the wires!

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to en-

sure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes

written in this manual.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this

manual or any unauthorized modication to the device.

Please consider that damages caused by manual modications to the device are not subject to warranty.

Never let the power-cord come into contact with other cables! Handle the power cord and all connections with

the mains with particular caution!

Make sure that the available voltage is not higher than stated on the rear panel.

WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable

to completely remove power from unit when not in use or before cleaning or servicing the unit.

Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the pow-

er-cord from time to time.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the pow-

er-cord by the plug. Never pull out the plug by tugging the power cord.

This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.

The electric connection, repairs and servicing must be carried out by a qualied employee.

Do not connect this device to a dimmer pack.

During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily

mean that the device is defective.

Do not touch the device’s housing bare hands during its operation (housing becomes hot)!

For replacement use fuses of same type and rating only.

LED light emission. Risk of eye injury.

Do not look straight at the xture´s LED source during operation. The intense light

beam may damage your eyes.

Do not view the light output with optical instruments or any device that may

concentrate the beam.

The light source contains blue LEDs.

2. Operating determination

This device is a moving head for creating decorative e󰀨ects and was designed for indoor use only.

This device is for professional use only. It is not for household use.

If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on

immediately. The arising condensation water might damage your device. Leave the device switched o󰀨 until

it has reached room temperature.

Do not shake the device. Avoid brute force when installing or operating the device.

Never lift the xture by holding it at the xture head, as the mechanics may be damaged. Always hold the xture

at the transport handles.

When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture

or dust. There should not be any cables lying around. You endanger your own and the safety of others!

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.

Always x the xture with an appropriate safety rope. Fix the safety rope at the correct holes only.

Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.

The maximum ambient temperature 45°C must never be exceeded.

CAUTION!

The front lens has to be replaced when it is obviously damaged,

so that its function is impaired, e. g. due to cracks or deep scratches!

Operate the device only after having familiarized with its functions. Do not permit operation by persons not

qualied for operating the device. Most damages are the result of unprofessional operation!

Do not block the front objective lens with any object when the xture is under operation.

The xture housing never must be covered with cloth or other materials.

Please use the original packaging if the device is to be transported.

Please consider that unauthorized modications on the device are forbidden due to safety reasons!

If this device will be operated in any way di󰀨erent to the one described in this manual, the product may su󰀨er

damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-cir-

cuit, burns, electric shock, burns etc.

CAUTION!

To avoid damage of the internal parts of the xture head, never let the sunlight lights

directly to the front lens , even when the xture is not working !

The product (covers and cables) must not be exposed to a high frequency electromagnetic eld higher than 3V/m.

Immunity of the equipment is designed according to the standard EN 55035 Electromagnetic compatibility of

multimedia equipment - Immunity requirements.

Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia

equipment – Emission Requirements according to class B.

Contains FCC ID: 2A6PL-DMXRDMRW001*

Contains IC: 29573-DMXRDMRW001*

* Wireless DMX version of the xture only.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Changes or modications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

The [Device] wireless operation is safe and complies to RF Exposure requirements

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

o󰀨 and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

3. Fixture exterior view

Rear panel of the base

15- Ethernet (RJ45)

16 - 3-pin DMX output

17 - 5-pin DMX output

18 - Fuse holder

19 - 3-pin DMX input

20 - 5-pin DMX input

21 - Power (PowerCon True 1)

Front panel of the base

9- QVGA touch screen

10 - ESCAPE button

11 - NEXT button

12 - PREV button

13 - ENTER/DISPLAY ON button

14 - USB port

The head has to be locked for transportation - the pan lock latch (6) and the tilt lock latch (7) have to be in the

locked positions. To unlock the head, move these latches to unlock positions before operating the xture.

1- Front lens (fresnel lens or PC lens

2 - Arm

3- Handle

4- Base

5- Control panel

6- Pan lock

7- Tilt lock

8- Head

The ENTER/DISPLAY ON button also serves for switching the display on (for a while) when the xture is dis-

connected from the mains.

Rear panel of the base - EP version

15 - Ethernet output (RJ45)

16 - 3-pin DMX output

17 - 5-pin DMX output

18 - Fuse holder

19 - Ethernet output (RJ45)

20 - 3-pin DMX input

21 - 5-pin DMX input

22 - Power (PowerCon True 1)

4. Installation

Fixtures must be installed by a qualied electrician in accordance with all

national and local electrical and construction codes and regulations.

4.1 Connection to the mains

For protection from electric shock, the xture must be earthed!

The xture is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC power

source from 100-240 Volts.

Power cable is enclosed to the xture.If you need to install a power plug on the power cable to allow connection

to power outlets, install a grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you

have any doubts about proper installation, consult a qualied electrician.

Core (EU) Core (US) Connection Plug Terminal Marking

Brown Black Live L

Light blue White Neutral N

Yellow/Green Green Earth

This device falls under class one and must be earthed (grounded).

To apply power, rst check that the head pan and tilt locks are released.

4.2 Replacing frost

Unplug the xture from mains before installing the frost module!

To replace the medium frost module.

1. Disconnect the xture from mains and allow it to cool for 10 minutes.

2. Remove plastic cover of the head by loosening the 2 quarter-turn fasteners on the cover to get access to

the frost module (1).

. The holder (2) of the frost foil is fastened to the frost holder (3) by means of the four magnets (4). Grip the

holder (2) and carefully tilt it out to break a force of magnets (4) on the frost holder (3).

. Place a new frost module into the frost holder (3). Check, that both slots (6) snapped correctly into two

protrusions (5) in the holder (3).

5. P

lace the plastic cover back on the xture before applying power.

4.3 Installing the top hat

Disconnect the xture from mains before installing the top hat.

1. Disconnect the xture from mains.

2. Insert the top hat (1) to the gel frame adaptor (2) and secure it by means of the spring lock (3).

4.4 Installing the module of Fresnel lens (module of PC lens)

Install the front lens with the device unplug from mains.

The front lens is heavy!

Secure the head in a horizontal position by means of the pan/tilt locks before

lens replacing.

1. Disconnect the xture from mains and allow it to cool.

2. Remove both head covers.

3. Secure the xture head in a horizontal position by means of the pan/tilt locks.

4. Unscrew two screws (4) on each side of the xture head and two screws (4) on the top side of

the head and remove the lens module (5), e.g. PC lens module.

Be careful, the lens module is heavy!

5. Place the new lens module (6), e.g. Fresnel lens module on the head, screw safety wire and fasten

the lens module by means of the six screws (4). Check that all screws are fully tightened before placing

the head covers back on the head.

6. Insert the top hat to the gel frame adaptor (2) if needed.

4.5 Rigging the xture

A structure intended for installation of the xture(s) must safely hold weight of the xture(s) placed on it. The

structure has to be certicated to the purpose.

The xture (xtures) must be installed in accordance with national and local electrical and construction codes

and regulations.

For overhead installation, the xture must be always secured with a safety wire

that can bear at least 10 times the weight of the xture

When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,

under high working places and other endangered areas is forbidden.

The operator has to make sure that safety relating and machine technical installations are approved by an ex-

pert before taking into operation for the rst time and after changes before taking into operation another time.

The operator has to make sure that safety relating and machine technical installations are approved by a skilled

person once a year.

Allow the xture to cool for ten minutes before handling.

The projector should be installed outside areas where persons may walk by or be seated.

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working

load limits, installation material being used, and periodic safety inspection of all installation material and the

projector. If you lack these qualications, do not attempt the installation yourself, but use a help of professional

companies.

CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety

of a possible installation, do not install the xture!

The xture has to be installed out of the reach of public.

The xture must never be xed swinging freely in the room.

Danger of re !

When installing the device, make sure there is no highly inammable

material (decoration articles, etc.) in a distance of min. 0.5 m.

CAUTION!

Use 2 appropriate clamps to rig the xture on the truss.

Follow the instructions mentioned at the bottom of the base.

Make sure that the device is xed properly! Ensure that the

structure (truss) to which you are attaching the xtures is secure.

The xture can be placed directly on the stage oor or rigged in any orientation on a truss without altering its

operation characteristics .

For securing the xture to the truss, install a safety wire which can hold at least 10 times the weight of the xture.

Use only the safety wire with a snap hook with screw lock gate.

Truss installation

1.Bolt clamps (4) to the brackets Omega CL (1) with M12 bolts and lock nuts through the hole in the bracket

Omega CL.

2.Fasten the brackets Omega CL on the bottom of the base by means of the quick-lock fasteners (2) and tighten

them fully clockwise.

3. Pull a safety wire (3) through the carrying handle and the truss (6) as hown on the picture below in a suitable

position so that the maximum fall of the xture will be 20 cm. Fasten a snap hook in the attachment point (5).

Use only the safety wire with a snap hooks with screw lock gates.

When installing xtures side-by-side,

avoid illuminating one xture with another!

DANGER TO LIFE!

Before taking into operation for the rst time,the installation has to be approved by

an expert!

1-Mounting bracket Omega CL

2-Quick-lock fasteners

3-Safety wire

4-Clamps

5-Attachment point

6-Truss

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de iluminación de Robe

Robe

Robe Color Mix 250 AT Series Manual de usuario

Robe

Robe Calumma Classic M MC Manual de usuario

Robe

Robe Flare CB Series Manual de usuario

Robe

Robe DigitalSpot 7100 DT Manual de usuario

Robe

Robe ANOLiS ArcSource Submersible II Manual de usuario

Robe

Robe Scan 575 XT Manual de usuario

Robe

Robe DigitalSpot 5000 DT Manual de usuario

Robe

Robe PATT 2017 Manual de usuario

Robe

Robe SPOT 250 XT Manual de usuario

Robe

Robe Anolis Calumma XS MC Manual de usuario

Robe

Robe Anolis Eminere 1 MC Manual de usuario

Robe

Robe Stage Faze 1500AT Manual de usuario

Robe

Robe Anolis Eminere Inground 2 Wireless DMX Manual de usuario

Robe

Robe ColorSpot 250 AT Manual de usuario

Robe

Robe Anolis Divine 160 RGBW/RGBA/PW/TW Manual de usuario

Robe

Robe ClubWash 600 CT Manual de usuario

Robe

Robe Anolis UVinere Remote 1 Manual de usuario

Robe

Robe Anolis Ambiane XP56 Manual de usuario

Robe

Robe Divine 160 RGBW Manual de usuario

Robe

Robe Robin DL4F Wash Manual de usuario

Robe

Robe Digital Spot 3000 DT II Manual de usuario

Robe

Robe Anolis Ambiane XP56 Manual de usuario

Robe

Robe Color mix 575 AT Manual de usuario

Robe

Robe LiteWare HO Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario