Robe Stage Banner 10 AT Series Manual de usuario
1
Version 1.1
2
3
Table of contents
1. Safety instructions ......................................................................................................... 3
2.Operating determinations............................................................................................... 4
3. Description of the device............................................................................................... 5
4. Installation....................................................................................................................... 6
4.1 Connection to the mains ............................................................................................ 6
4.2 Changing the power supply settings .......................................................................... 6
4.3 Rigging the xture ...................................................................................................... 7
4.4 DMX-512 connection/connection between xtures .................................................... 9
5. StageBanner 10 AT-DMX Protocol-version 1.0.......................................................... 10
6. Operating modes ......................................................................................................... 11
6.1 Controller mode........................................................................................................ 11
6.2 Stand-alone mode.................................................................................................... 11
7.Control menu map......................................................................................................... 12
8. Control menu ............................................................................................................... 14
8.1 Fixture Address ....................................................................................................... 14
8.2 Slave control ........................................................................................................... 14
8.3 Fixture informations.................................................................................................. 14
8.4 Personality ............................................................................................................... 15
8.5 Manual mode ........................................................................................................... 16
8.6 Test sequences........................................................................................................ 16
8.7 Stand-alone setting ................................................................................................. 16
8.8 Reset function .......................................................................................................... 17
8.9 Special functions ...................................................................................................... 17
9. Low power mode .......................................................................................................... 18
10. Error and information messages .............................................................................. 19
11. Technical specications............................................................................................ 19
12. Maintenance and cleaning......................................................................................... 20
StageBanner 10 AT
2
3
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualiled
- follow the instructions of this manual
CAUTION!
Be careful with your operations.
With a high voltage you can suffer
a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to en-
sure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
Never let the power-cord come into contact with other cables! Handle the power cord and all connections with
the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
Always plug in the power plug least. Make sure that the power-switch is set to Off-position before you connect
the device to the mains. The power plug has to be accessable after installing the device.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-
cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-
cord by the plug. Never pull out the plug by tugging the power cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to
earth.
The electric connection, repairs and servicing must be carried out by a qualied employee.
Do not connect this device to a dimmer pack.
During the initial start-up some smell may arise. This is a normal process and does not necessarily mean that
the device is defective.
4
5
2.Operating determinations
This device was designed for indoor use only.
If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Do not shake the device. Avoid brute force when installing or operating the device.
Always hold the device at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture
or dust. There should not be any cables lying around. You endanger your own and the safety of others!
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the x-
ture.
Always x the xture with an appropriate safety rope. Fix the safety rope at the correct holes only.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fas-
tened.
The maximum ambient temperature 45°C must never be exceeded.
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the device. Most damages are the result of unprofessional operation!
CAUTION!
The maximum load of the device is 10 kg !
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modications on the device are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void.
4
5
3. Description of the device
1- Quick-lock fastener
2 - Omega holder
3 - Rotating plate
4 - Top covers
Rear panel of the xture
5- Power switch
6 - Power cord
7 - Fuse holder
8 - 3-pin DMX output
9 - 3-pin DMX input
10 - 5-pin DMX output
11 - 5-pin DMX input
Front panel of the xture:
12 - Mode-button
13 - Enter-button
14 - Up-button
15 - Down-button
16 - Display
6
7
4. Installation
4.1 Connection to the mains
Verify the power supply settings before applying power!
If you wish to change the power supply settings,see the chapter below.
Connect the xture to the mains with the power cord.
If the plug on the exible cord is not the right type for your socket outlets,do not use an adaptor,but remove the
plug from the cord and discard.Carefully prepare the end of the the supply cord and t a suitable plug.
The earth has to be connected!
The occupation of the connection-cables is as follows:
Cable (EU) Cable (US) Pin International
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
4.2 Changing the power supply settings
Both the transformer and the ballast must be connected correctly for the local AC voltage and frequency.
The wrong settings can cause poor performance or demage of the xture.The factory settings are printed next
to the power switch.
If you want to change the power supply settings,follow the instructions:
1.Disconnect the xture from AC power.
2.Remove the top base covers by loosening the 10 fastening screws.
3.Move the wire 1 on the transformer connection block to the position according to the desired voltage.
4.Close the base before applying AC power.
Examples:
AC 230V/50Hz
US-version:
EU-version:
AC120V/60Hz
6
7
4.3 Rigging the xture
DANGER TO LIFE!
Please consider the respective national norms during the installation!
The installation must only be carried out by an authorized distributor!
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down if
the main attachment fails.
When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert
before taking into operation for the rst time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all installation
material and the device. If you lack these qualications, do not attempt the installation yourself, but instead use
a professional structural rigger. Improper installation can result in bodily injury and.or damage to property.
The device has to be installed out of the reach of people.
If the device shall be lowered from the ceiling or high joists, professional trussing systems have to be used.
The device must never be xed swinging freely in the room.
Caution: Devices may cause severe injuries when crashing down! If you have doubts concerning the safety of
a possible installation, do NOT install the device!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the device’s
weight.
CAUTION !
Provide a minimum clearance of 0.1meters around fans and air vents.
CAUTION!
Use 2 appropriate clamps to rig the device on the truss.
Maximum load of the xative plate is 10 kg.
Make sure that the device is xed properly! Ensure that the
structure (truss)to which you are attaching the xtures is secure.
The device can be placed directly on the stage oor or rigged in any orientation on a truss without altering its
operation characteristics .
For overhead use, always install a safety-rope that can hold at least 10 times the weight of the device. You must
only use safety-ropes with screw-on carabines. Pull the safety-rope through the two apertures on the bottom of
the base and over the trussing system etc. Insert the end in the carabine and tighten the xation screw.
8
9
Possible Installation:
.
Overhead installation:
1.Bolt each clamp (1) (not included) to the omega holder (4) with M12 bolt and lock nut through the hole in
the holder.
2.Fasten the omega holders on the bottom of the base by inserting both quick-lock fasteners (3) into the holes
of the base and tighten fully clockwise.
3.Fasten the safety cable (2) through the two apertures on the bottom of the base and over the trussing sys-
tem.
1-Clamp
2-Safety cable
3-Quick-lock fastener
4-Omega holder
advertising
plate
Omega holder
safety cable
xing clamp
clamp
rotating plate
8
9
4.4 DMX-512 connection/connection between xtures
The xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired
in parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in
order to connect the controller with the xture or one xture with another.
DMX - output DMX-input
XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with
the DMX input of the rst xture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-out-
puts, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture. Always
connect one output with the input of the next xture until all xtures are connected.
Caution: At the last xture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last xture.
Building a master/slave-chain:
Connect the DMX-output of the master xture in the data-chain with the DMX-input of the rst slave. Always
connect output with the input of the next slave until all slaves are connected (up to 9 xtures).
Caution:It’s necessary to insert the XLR termination plug (with 120 Ohm) into the input of the master xture
and into the output of the last slave xture in the link in order to ensure proper transmission on the data link.
Master/slave operation
Controller operation
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
10
11
5. StageBanner 10 AT - DMX Protocol-version 1.0
Channel Value Function Type of control
10 - 255 Pan coarse
Coarse control of pan movement by 360° proportional
20 - 255 Pan Fine
Fine control of pan movement proportional
3
0
1 - 255
1 - 255
Pan speed
Max. speed (tracking mode)
Pan speed-set Speed Mode in menu: Pan Mode
Speed from max. to min. (vector mode)
Pan time - set Time Mode in menu: Pan Mode
Time from 0,1 s to 25,5 s.
step
proportional
proportional
4
0 - 129
130 - 139
140 - 199
200 - 255
Pan functions
Standard operation (xture is controlled by channels 1, 2 and 3)
Reset of the pan
Forward pan rotation (speed is controlled by channel 3)
Backward pan rotation (speed is controlled by channel 3)
step
step
step
step
Note for programming:
If you want to keep the same direction of the pan movent around 0 DMX (255DMX) value,the difference
betwen the start point A and stop point B must not be greather than 120°(=85 DMX values).If this difference is
more than 85 DMX,the pan will move in reverse direction.
Tabla de contenidos
Otros manuales de Equipo de iluminación de Robe
Robe
Robe ClubScan 150CT Manual de usuario
Robe
Robe LiteWare HO Manual de usuario
Robe
Robe ClubWash 600 CT Manual de usuario
Robe
Robe XT Series Manual de usuario
Robe
Robe Robin 600E Beam Manual de usuario
Robe
Robe ROBIN LEDBeam 350 RGBA Manual de usuario
Robe
Robe DigitalSpot 7000 DT Manual de usuario
Robe
Robe Haze 400 FT Manual de usuario
Robe
Robe ANOLiS ArcSource Submersible II Manual de usuario
Robe
Robe Colormix 240 AT Manual de usuario
Robe
Robe Color mix 575 AT Manual de usuario
Robe
Robe Anolis Ambiane XP56 Manual de usuario
Robe
Robe Stage Faze 1500AT Manual de usuario
Robe
Robe CitySource 96 Manual de usuario
Robe
Robe Robin 100 LEDBeam Wireless DMX CRMX Manual de usuario
Robe
Robe Color Mix 250 AT Series Manual de usuario
Robe
Robe ANOLiS Eminere Remote UV 2 Manual de usuario
Robe
Robe ClubWash 250CT Manual de usuario
Robe
Robe Robin T11 Profile Manual de usuario
Robe
Robe Euphoria CB series Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
