ProLights EclFresnel CT+M Manual de usuario
USER MANUAL
REV.01-10/23-PRELIMINARY English version
EclFresnel CT+M
EclFresnel CT+MIP
350W 6 colours LED Fresnel with 9,4°-80,8°
zoom
Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
Visit the download area
of the product page
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services
or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
EclFresnel CT+M EclFresnel CT+MIP
01PROLIGHTS - EclFresnel CT+M / EclFresnel CT+MIP
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
OPTIONAL ACCESSORIES............................................................................................. 05
2 - TECHNICAL DRAWING 06
3 - INSTALLATION 10
MOUNTING.................................................................................................................... 10
4 - CONNECTION TO THE MAINS SUPPLY 11
5 - START UP 11
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 11
6 - PRODUCT OVERVIEW 12
7 - DMX CONNECTION 13
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 13
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 13
CONNECTION DAISY CHAIN........................................................................................ 13
CONNECTION OF THE DMX LINE................................................................................ 13
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 14
DMX ADDRESSING ........................................................................................................ 14
8 - CONTROL PANEL 15
DISPLAY AND BUTTONS LAYOUT................................................................................. 15
9 - MENU STRUCTURE 16
10 - RDM FUNCTIONS 20
11 - DMX CHARTS 21
12 - ACCESSORIES INSTALLATION 58
FILTER FRAME (CODE ECLFRCTPMFF) ......................................................................... 58
BARN DOOR (CODE ECLFRCTPMBD)........................................................................... 59
SLIDING BRACKET MOVEMENT ................................................................................... 60
13 - MAINTENANCE 61
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 61
REPLACING THE FUSE................................................................................................... 61
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 61
TROUBLESHOOTING..................................................................................................... 62
PROLIGHTS - EclFresnel CT+M / EclFresnel CT+MIP02
SAFETY INFORMATION
WARNING!
• See https://www.prolights.it/product/ECLFRCTPM#download for installation instructions.
• Please read carefully the instruction reported in this section before installing, power-
ing, operating or servicing the product and observe the indications also for its future
handling.
This unit is not for household use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical
installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, ca-
ble, or other components are damaged, defective, deformed or showing signs of
overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
0,5 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0.5 meters (1.64 ft) from the lens of the projector.
03PROLIGHTS - EclFresnel CT+M / EclFresnel CT+MIP
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 2 according to EN 62471.
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-
pose/ recycle this product at the end of its life according to the local regulation.
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).
• 2014/30/EU - Electromagnetic Compatibility (EMC).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
Other approvals
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
• The device should be positioned so that prolonged staring into the luminaire at adis-
tance closer than 14,54 m (47,70 ft) is not expected.
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
10.5 m
34.45 ft
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
10.5 m
34.45 ft
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
14,54 m
47,70 ft
PROLIGHTS - EclFresnel CT+M / EclFresnel CT+MIP04
ECLFRCTPM - IP20 Version
Indoor use
• This product is designed for indoor and dry environments.
• Do not use in wet location and do not expose the xture to rain or moisture.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
T
45°
C
a
Max operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
T
-10°
C
aMinimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -10 °C (14 °F).
T
70°
C
c
Temperature of the external surface
• The surface of the xture can reach up to 70 °C (158 °F) during operation. Avoid
contact with people and materials.
ECLFRCTPMIP - IP65 Version
IP65
Permanent Outdoor use
• This product is rated with an IP (Ingress protection) for permanent outdoor use when
used and serviced according to the instruction contained in this document.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
T
45°
C
aMax operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).
T -20°C
a
Minimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).
T 80°C
c
Temperature of the external surface
• The surface of the xture can reach up to 80 °C (176 °F) during operation. Avoid
contact with people and materials.
05PROLIGHTS - EclFresnel CT+M / EclFresnel CT+MIP
1 - PACKAGING
PACKAGE CONTENT
• 1x ECLFRESNEL CT+M / CT+MIP;
• 1x ECLFRSPG: spigot for PROLIGHTS Fresnel series;
• 1x ECLFRCTPMBD: barn door with 8 directional aps to adjust the light beam;
• 1x ECLFRCTPMFF: lter frame for ECLFRESNEL series;
• 1x 1,5 meters power cable (BARE END - NEUTRIK POWERCON TRUE1 IP65);
• 1x User manual
OPTIONAL ACCESSORIES
• FCLECLFRCTPM: Flight case for 4 pcs of ECLFRCTPM series
• ECLFRCTPMBAG1U: Empty ABS case for 1 pc of ECLFRCTPM series
• ECLFRCTPMKPOYO: Pole operated aluminium yoke bracket and zoom kit for ECLFRCTPM series
• SPGM10: 28mm spigot for xtures, M10 bolt
• SPGM12: 28mm spigot for xtures, M12 bolt
• LRTM2SPIBK: CRMX Timo Two SPI kit, black
• EFSBUFDS: SNAPBAG - Universal Small Deeper for barndoors
• SPGM10: 28mm spigot for xtures, M10 bolt
• SPGM12: 28mm spigot for xtures, M12 bolt
• UPBOXPRO: Firmware uploader kit, USB IN, 5pin XLR DMX OUT
• UPBOX1UP5: Firmware uploader kit, USB IN, 5pin XLR DMX OUT
• C6040B: Aluminum clamp for 28mm spigot, 200kg load, 48-51mm tubes, black inc
• TOUR53415L03: Dmx cable HC5340. CANC5MXX XLR 5p->CANC5FXX XLR (f) 5p, L.3m
• 958225L03: 3x2.5mm TH07 Cable, 16A 3p PwCon MXW, 16A 3p PwCon FXW, L. 3m
• 9513FXWL03: Ass. 3x2.5mm TH07 cable, 16A 3p 230V CEE plug, MENAC3FXW socket, L.3 m
• RSR0630B: Steel security cable for hanging bodies, inox steel shackle, L=60 cm, black
• C6002B: Slim aluminum clamp, 200kg loading, 48-51mm tubes, M10 bolt, Black
• 9533FXWL03: Ass. 3x2.5mm TH07 cable, SHUKO plug, MENAC3FXW socket, L.3m
PROLIGHTS - EclFresnel CT+M / EclFresnel CT+MIP06
2 - TECHNICAL DRAWING
338 mm
[13.3 in]
466 mm
[18.3 in]
587 mm
[23.1 in]
121 mm
[4.8 in]
284 mm
[11.2 in]
428 mm
[16.9 in]
493 mm
[19.4 in]
614 mm
[24.2 in]
300 mm
[11.8 in]
121 mm
[4.8 in]
428 mm
[16.9 in]
367 mm
[14.4 in]
479 mm
[18.9 in]
606 mm
[23.9 in]
127 mm
[5.0 in]
300 mm
[11.8 in]
513 mm
[20.2 in]
634 mm
[25.0 in]
121 mm
[4.8 in]
Fig. 01ECLFRCTPM+ECLFRCTPMKPOYO - Weight: 11,9 kg - 26,23 lbs
ECLFRCTPM - Weight: 9,9 kg / 21,82lbs
07PROLIGHTS - EclFresnel CT+M / EclFresnel CT+MIP
121 mm
[4.8 in]
466 mm
[18.3 in]
587 mm
[23.1 in]
555 mm
[21.9 in]
121 mm
[4.8 in]
620 mm
[24.4 in]
741 mm
[29.2 in]
300 mm
[11.8 in]
606 mm
[23.9 in]
555 mm
[21.9 in]
761 mm
[29.9 in]
300 mm
[11.8 in]
Fig. 02
ECLFRCTPM - Weight: 9,9 kg / 21,82lbs
ECLFRCTPM+ECLFRCTPMKPOYO - Weight: 11,9 kg - 26,23 lbs
PROLIGHTS - EclFresnel CT+M / EclFresnel CT+MIP08
2 - TECHNICAL DRAWING
338 mm
[13.3 in]
470 mm
[18.5 in]
591 mm
[23.3 in]
121 mm
[4.8 in]
428 mm
[16.9 in]
620 mm
[24.4 in]
499 mm
[19.6 in]
304 mm
[12.0 in]
121 mm
[4.8 in]
304 mm
[12.0 in]
641 mm
[25.2 in]
428 mm
[16.9 in]
367 mm
[14.4 in]
611 mm
[24.0 in]
Fig. 01
ECLFRCTPMIP+ECLFRCTPMKPOYO - Weight: 12,9 kg - 28,44 lbs
ECLFRCTPMIP - Weight: 10,9 kg / 24,03 lbs
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipo de iluminación de ProLights
ProLights
ProLights EclMini CC Manual de usuario
ProLights
ProLights Diamond142L Manual de usuario
ProLights
ProLights EclSoft Tube100 Manual de usuario
ProLights
ProLights ArcPod 15VW Manual de usuario
ProLights
ProLights V575SPOT Manual de usuario
ProLights
ProLights ECLJZIPLZ1530 Manual de usuario
ProLights
ProLights PINSPOT 101 Manual de usuario
ProLights
ProLights ARCLED2033 Manual de usuario
ProLights
ProLights EclNanoPanel TWC Manual de usuario
ProLights
ProLights NANOLASERRG Manual de usuario
ProLights
ProLights LUMIPAR7IRTRI Manual de usuario
ProLights
ProLights Krypton 40G Manual de usuario
ProLights
ProLights Lumipix9HE Manual de usuario
ProLights
ProLights FS75LED Manual de usuario
ProLights
ProLights spider Manual de usuario
ProLights
ProLights PIXBAR3E Manual de usuario
ProLights
ProLights V200SPOT Manual de usuario
ProLights
ProLights EclPar IPMFC Manual de usuario
ProLights
ProLights ECL Series Manual de usuario
ProLights
ProLights EclPanel TWC Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
