ProLights EclPar IPMFC Manual de usuario

USER MANUAL

English version

EclPar IPMFC

100W IP65 RGB+WW single source LED PAR

REV.01-08/23

Thank you for choosing PROLIGHTS

Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements

for professionals and designed and manufactured for the use and application as shown in this document.

Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be

a source of danger.

This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively

applicable national accident prevention rules and regulations.

Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated

companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other

loss occasioned by the use of, inability to use or reliance on the information contained in this document.

Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial

PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).

Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad

set of always updated technical documentation: specications, user manual, technical drawings, photometrics,

personalities, xture rmware updates.

The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services

or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.

04026 - Minturno (LT) ITALY.

Visit the download area

of the product page

PROLIGHTS - EclPar IPMFC 01

INDEX

SAFETY INFORMATION 02

1 - PACKAGING 05

PACKAGE CONTENT..................................................................................................... 05

OPTIONAL ACCESSORIES............................................................................................. 05

2 - TECHNICAL DRAWING 06

3 - INSTALLATION 07

MOUNTING.................................................................................................................... 07

4 - CONNECTION TO THE MAINS SUPPLY 08

5 - START UP 08

CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 08

6 - PRODUCT OVERVIEW 09

7 - DMX CONNECTION 10

CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 10

INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 10

CONNECTION DAISY CHAIN........................................................................................ 10

CONNECTION OF THE DMX LINE................................................................................ 10

CONSTRUCTION OF THE DMX TERMINATION ........................................................... 11

DMX ADDRESSING ........................................................................................................ 11

OPERATION AS A WIRELESS TRANSMITTER................................................................ 11

IN TO CRMX................................................................................................................... 12

OPERATION AS A WIRELESS RECEIVER........................................................................ 12

CRMX TO DMX (RX) ....................................................................................................... 12

8 - CONTROL PANEL 13

DISPLAY AND BUTTONS LAYOUT................................................................................. 13

9 - MENU STRUCTURE 14

10 - SHORTCUT 18

11 - RDM FUNCTIONS 19

13 - DMX CHARTS 23

RDM Personality ID List .................................................................................................. 23

RDM Model ID................................................................................................................ 23

14 - ERROR MESSAGES 31

15 - ACCESSORIES INSTALLATION 32

LENS ASSEMBLY (EPIPMLENS15 - 15° lens INCLUDE; EPIPMLENS30 - 30° lens

OPTIONAL; EPIPMLENS60 - 60° lens OPTIONAL;) ..................................................... 32

EPIPMLENS15................................................................................................................. 33

EPIPMLENS30................................................................................................................. 33

EPIPMLENS60................................................................................................................. 33

BARN DOOR (CODE AJP7ZIPBD - OPTIONAL)............................................................. 34

BARN DOOR (CODE AJP7ZIPBD - OPTIONAL)............................................................. 35

FULL SNOOT (CODE EPIPMFSNOOTBK - OPTIONAL)................................................. 36

HONEYCOMB LOUVRE (CODE EPIPMHLOUVREBK - OPTIONAL)............................... 37

CONCENTRIC LOUVRE (CODE EPIPMCLOUVREBK - OPTIONAL)............................... 38

LENS ASSEMBLY FROM INSIDE..................................................................................... 39

LENS ASSEMBLY FROM INSIDE..................................................................................... 40

16 - PERIODICAL CLEANING 41

17 - TEST OF IP65 RATING 42

18 - MAINTENANCE 43

MAINTENANCE AND CLEANING THE PRODUCT........................................................ 43

REPLACING THE FUSE................................................................................................... 43

VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 43

TROUBLESHOOTING..................................................................................................... 44

PROLIGHTS - EclPar IPMFC02

SAFETY INFORMATION

WARNING!

• See https://www.prolights.it/product/ECLPARIPMFC#download for installation in-

structions.

• Please read carefully the instruction reported in this section before installing, powering,

operating or servicing the product and observe the indications also for its future handling.

This unit is not for household and residential use, only professional applications.

Connection to mains supply

• The Connection to the mains supply must be carried out by a qualied electrical

installer.

• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected

to ground (earth).

• Select the cable cross section in according with the maximum current draw of the

product and the possible number of products connected at the same power line.

• The AC mains power distribution circuit must be equipped with magnetic+residual

current circuit breaker protection.

• Do not connect it to a dimmer system; doing so may damage the product.

Protection and Warning against electrical shock

• Do not remove any cover from the product, always disconnect the product from AC

power before servicing.

• Ensure that the xture is electrically connected to ground (earth). And use only a

source of AC power that complies with local building and electrical codes and has

both overload and ground-fault (earth-fault) protection.

• Before using the xture, check that all power distribution equipment and cables are

in perfect condition and rated for the current requirements of all connected devices.

• Isolate the xture from power immediately if the power plug or any seal, cover, ca-

ble, or other components are damaged, defective, deformed or showing signs of

overheating.

• Do not reapply power until repairs have been completed.

• Refer any service operation not described in this manual to PROLIGHTS Service team

or an authorized PROLIGHTS service center.

Installation

• Make sure that all visible parts of the product are in good visible condition before its

use or installation.

• Make sure the point of anchorage is stable before positioning the projector.

• When suspending the xture above ground level, secure it against failure of primary

attachments by attaching a safety cable that is approved as a safety attachment for

the weight of the xture to the attachment point on the main frame of the product. ln

case the safety cable, enter in action, it needs to be replaced with a new one.

• Install the product only in well ventilated places.

• For non temporary installations, ensure that the xture is securely fastened to a load-

bearing surface with suitable corrosionresistant hardware.

• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or

screws are turned fully, and secured with a suitable safety cable.

1,4 m Minimum distance of illuminated objects

• The projector needs to be positioned so that the objects hit by the beam of light are

at least 1,4 meters (4,7 ft) from the lens of the projector.

PROLIGHTS - EclPar IPMFC 03

T 45°C

Max operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).

T -20°C

Minimum operating ambient temperature (Ta)

• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).

Protection from burns and re

• The exterior of the xture becomes hot during use. Avoid contact by persons and

materials.

• Ensure that there is free and unobstructed airow around the xture.

• Keep ammable materials well away from the xture.

• Do not expose the front glass to sunlight or any other strong light source from any an-

gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.

• Do not attempt to bypass thermostatic switches or fuses.

IP65

Outdoor (temporary) use

• This product is rated with an IP (Ingress protection) for temporary outdoor use when

used and serviced according to the instruction contained in this document.

• Never use the xture in places subject to vibrations or bumps.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Excessive dust, smoke uid, and particle build up degrades performance, causes

overheating and will damage the xture.

• Damages caused by inadequate cleaning or maintenance are not covered by the

product warranty.

T 75°C

Temperature of the external surface

• The surface of the xture can reach up to 75 °C (167 °F) during operation. Avoid

contact with people and materials.

Maintenance

• Warning! Disconnect the xture from AC mains power and allow to cool for at least

10 minutes before handling.

• Only technicians who are authorized by PROLIGHTS or Authorised service partners

are permitted to open the xture.

• Users may carry out external cleaning, following the warnings and instructions pro-

vided, but any service operation not described in this manual must be referred to a

qualied service technician.

• Important! Excessive dust, smoke uid, and particle build up degrades performance,

causes overheating and will damage the xture. Damages caused by inadequate

cleaning or maintenance is not covered by the product warranty.

Photobiological safety

• This device emits potentially dangerous optical radiation and is identied in the cat-

egory of Risk Group 2 according to EN 62471.

Do not stare at the operating light source

• Do not look directly at the LED source during operation. It can be harmful to the eyes

and skin.

• During Installation, operation and maintenance, be prepared for the xture to light

and move suddenly when connected to power.

• The device should be positioned so that prolonged staring into the luminaire at adis-

tance closer than 4 m (13,12 ft) is not expected.

PROLIGHTS - EclPar IPMFC04

Minimun

distance

Risk

Group 2

Risk

Group 1

0.2 m

0.7 ft

10.5 m

34.45 ft

Minimun

distance

Risk

Group 2

Risk

Group 1

0.2 m

0.7 ft

10.5 m

34.45 ft

Minimun

distance

Risk

Group 2

Risk

Group 1

0.2 m

0.7 ft

4,0 m

13,12 ft

Disposal

• This product is supplied in compliance with European Directive 2012/19/EU – Waste

Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-

pose/ recycle this product at the end of its life according to the local regulation.

The products to which this manual refers comply with:

• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).

• 2014/30/EU - Electromagnetic Compatibility (EMC).

• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).

The products to which this manual refers comply with:

• UL 1573 + CSA C22.2 No. 166 - Stage and Studio Luminaires and Connector Strips.

• UL 1012 + CSA C22.2 No. 107.1 - Standard for power units other than class 2.

FCC Compliance:

• This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may

cause undesired operation.

Other approvals

PROLIGHTS - EclPar IPMFC 05

1 - PACKAGING

PACKAGE CONTENT

• 1 x ECLPARIPMFC

• 1 x EPIPMLENS15

• 1 x ECLPARTPG

• 1 x 1,5 meters power cable (BARE END - SEETRONIC IP65 power connector)

• 1 x User Manual

OPTIONAL ACCESSORIES

• LECLPARIPM: Flight-case per contenere 6 pc serie ECLPARIPM

• EPIPMBAG1U: ABS case vuoto per contenere 1 pc serie ECLPARIPM

• ECLPARIPMBDBK: 8 alette direzionali per la regolazione del fascio di luce, ECLPARIPM, nero

• ECLPARTPG: Telaio porta gelatina per proiettori ECLPAR

• EPIPMRFFBK: Telaio porta gelatina circolare per ECLPARIPM series, nero

• ECLPARIPMWKBK: CRMX Timo Fx kit per serie ECLPARIPM, nero

• EPIPMLENS15: Lente a 15° per serie ECLPARIPM

• EPIPMLENS30: Lente a 30° per serie ECLPARIPM

• EPIPMLENS60: Lente a 60° per serie ECLPARIPM

• EPIPMFILT1040: Diffusore di luce per ECLPARIPM, asimmetrico 10°x40°

• EPIPMFILT1060: Diffusore di luce per ECLPARIPM, asimmetrico 10°x60°

• EPIPMFILT1090: Diffusore di luce per ECLPARIPM, asimmetrico 10°x90°

• EPIPMFILT3060: Diffusore di luce per ECLPARIPM, asimmetrico 30°x60°

• EPIPMFSNOOTBK: Visiera completa per serie ECLPARIPM, nero

• EPIPMHLOUVREBK: Filtro anti abbagliamento a nido d'ape per serie ECLPARIPM, nero

• EPIPMCLOUVREBK: Filtro anti abbagliamento concentrico per serie ECLPARIPM, nero

• SPGM10: Spigot 28mm per xtures, perno M10

• SPGM12: Spigot 28mm per xtures, perno M12

• UPBOX1UP5: Interfaccia aggiornamento rmware, USB IN, 5p XLR DMX OUT, USB OUT

• UPBOXPRO: Interfaccia aggiornamento rmware, USB IN, connettore XLR DMX OUT 5-pin

• TOUR53415L03: Cavo Dmx assembl. HC5340, CANC5MXX XLR 5p -> CANC5FXX XLR (f) 5p, L.3m

• TOUR53413L03: Cavo Dmx assembl. HC5340 CANC3MXX XLR 3p -> CANC3FXX XLR (f) 3p, L.3m

• 958025L03: Cavo TH07 3x2.5mm, PwCon FCA 3p 20A, PwCon FCB 3p 20A, L. 3m

• 9513FCAL03: Cavo Ass. TH07 3x2.5mm, spina CEE 3p 16A 230V, presa MENAC3FCA, L.3 m

• RSR0630B: Cavo di sicurezza acciaio per corpi sospesi, moschettone inox, L=60 cm, nero

• C6002B: Clamp in alluminio Slim, port.200Kg, tubi 48-51mm, perno M10, Black

• 9533FCAL03: Cavo Ass. TH07 3x2.5mm, spina SCHUKO, presa MENAC3FCA, L.3 m