Planet XGS-6350-48X2Q4C Manual de usuario

Layer 3 24-/48-Port 10G SFP+ plus 4-Port 100G

QSFP28 Managed Switch

XGS-6350-24X4C/XGS-6350-48X2Q4C

Quick Installation Guide

Table of Contents

1. Package Contents ....................................................................................... 3

2. Switch Management.................................................................................... 4

3. Requirements ............................................................................................. 5

4. Terminal Setup ........................................................................................... 6

4.1 Logging on to the Console.................................................................... 7

 4.2 ConguringIPAddress......................................................................... 8

 4.3 Setting1000BASE-Xfor10GSFP+Port................................................. 9

 4.4 Setting40GBASE-Xfor100GSFP+Port ...............................................10

 4.5 ChangingPassword.............................................................................10

 4.6 SavingtheConguration .....................................................................11

5. Starting Web Management .........................................................................12

 5.1 LoggingintotheManagedSwitchfromManagementPort .....................13

 5.2 SavingCongurationviatheWeb ........................................................14

6. LEDIndicators...........................................................................................15

 6.1 XGS-6350-24X4C ...............................................................................15

 6.2 XGS-6350-48X2Q4C ...........................................................................16

7. Customer Support .....................................................................................18

1. Package Contents

Thank you for purchasing PLANET Layer 3 24-/48-Port 10G SFP+ plus 4-Port 100G

QSFP28ManagedSwitch,XGS-6350-24X4C/XGS-6350-48X2Q4C.

Unless specied, “Managed Switch” mentioned in this Quick Installation Guide

referstotheXGS-6350-24X4C/XGS-6350-48X2Q4C.

Open the box of the Managed Switch and carefully unpack it. The box should

containthefollowingitems:

XGS-6350-24X4C XGS-6350-48X2Q4C

QuickInstallationGuide  

DB9toRJ45InterfaceRS232

Console Cable  

RackMountAccessoryKit  

ACPowerCord  

SFPDustCap 28 54

If any item is found missing or damaged, please contact your local reseller for

replacement.

2. Switch Management

To set up the Managed Switch, the user needs to congure the Managed Switch

fornetwork management.The ManagedSwitch providestwo managementoptions:

Out-of-Band Management and In-Band Management.

Out-of-Band Management

Out-of-band management is the management through console interface.

Generally, the user will use out-of-band management for the initial switch

conguration,orwhenin-bandmanagementisnotavailable.

In-Band Management

In-band management refers to the management by logging in to the Managed

Switchusing Telnetor HTTP,orusing SNMPmanagement softwaretocongure the

Managed Switch. In-band management enables the management of the Managed

SwitchtoattachsomedevicestotheSwitch.Thefollowingproceduresarerequired

toenablein-bandmanagement:

1. Log on to console

2.Assign/CongureIPaddress

3. Create a remote login account

4.EnableHTTPorTelnetserverontheManagedSwitch

In case in-band management fails due to Managed Switch conguration changes,

out-of-band management can be used for conguring and managing the Managed

Switch.

The Managed Switch is shipped with Management Port IP

address 192.168.1.1/24 assigned and VLAN1 interface IP

address 192.168.0.254/24 assigned by default. User can assign

another IP address to the Managed Switch via the console inter-

face to be able to remotely access the Managed Switch through

Telnet or HTTP.

3. Requirements

zWorkstations running Windows XP/2003/Vista/2008/7/8/10, MAC OS X or later,

Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.

zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)

zSerial Port Connection(Terminal)

 The above Workstations come with COM Port (DB9) or USB-to-RS232

converter.

 The above Workstations have been installed with terminal emulator, such as

Tera Term or PuTTY.

 Serial cable -- one end is attached to the RS232 serial port, while the other

endtotheconsoleportoftheManagedSwitch.

zManagement Port Connection

 Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.

 TheabovePCisinstalledwithWebbrowser.

Note

Itis recommended touse InternetExplorer8.0 orabovetoaccess

the Managed Switch. If the Web interface of the Managed Switch

is not accessible, please turn off the anti-virus software or firewall

andthentryitagain.

4. Terminal Setup

To congure the system, connect a serial cable to a COM port on a PC or

notebook computer and to serial (console) port of the Managed Switch. The

console port of the Managed Switch is DCE already, so that you can connect the

consoleportdirectlythroughPCwithouttheneedofNullModem.

Managed Switch

PC / Workstation

with

Terminal Emulation Software

Serial Port

RS232 to RJ45 Cable

Console Port

RJ45

Figure 4-1 Managed Switch Console Connectivity

A terminal program is required to make the software connection to the Managed

Switch. Tera Term program may be a good choice. The Tera Term can be accessed

fromtheStart menu.

1. Click STARTmenu,thenPrograms,andthenTera Term.

2.When the following screen appears, make sure that the COM port should be

conguredas:

Baud:9600

Parity:None

Databits:8

Stopbits:1

Flowcontrol:None

Figure 4-2 Tera Term COM Port Conguration

4.1 Logging on to the Console

Once the terminal is connected to the device, power on the Managed Switch, and

theterminalwilldisplay“running testing procedures”.

Then, the following message asks for the login user name and password. The

factory default user name and password are as follows as the login screen in

Figure4-3appears.

Username:admin

Password:admin

Figure 4-3 Managed Switch Console Login Screen

The user can now enter commands to manage the Switch. For a detailed

descriptionofthecommands,pleaserefertothefollowingchapters.

Note

1.Forsecurity reason,please changeand memorizethenew pass-

wordafterthisfirstsetup.

2.Accept command in lowercase or uppercase letter under console

interface.

4.2 ConguringIPAddress

The IP address conguration commands for VLAN1 interface are listed below.

Before using in-band management, the Managed Switch must be congured with

an IP address by out-of-band management (i.e. console mode). The conguration

commandsareasfollows:

Switch#cong

Switch_cong#interface vlan 1

Switch_cong_v1#ip address 192.168.1.254 255.255.255.0

ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.

IPv4 Address: 192.168.1.254

Subnet Mask: 255.255.255.0

Figure 4-4 Conguring IPv4 Address Screen

To check the current IP address or modify a new IP address for the Managed

Switch,pleaseusetheproceduresasfollows:

Show the current IP address

1. On “Switch#”prompt,enter“show ip interface brief”.

2.The screen displays the current IP address, subnet mask and gateway as shown

inFigure4-5.

Figure 4-5 Showing IP Information Screen

If the IP is successfully congured, the Managed Switch will apply the new IP

address setting immediately. You can access the Web interface of Managed Switch

throughthenewIPaddress.

Note

Ifyouarenotfamiliarwithconsolecommandortherelatedparam-

eter,enter“help”anytimeinconsoletogetthehelpdescription.

4.3 Setting1000BASE-Xfor10GSFP+Port

The Managed Switch supports both 1000BASE-X and 10GBASE-X SFP

transceivers by manual setting and the default SFP+ port speed is set to 10Gbps.

For example, to establish the ber connection with 1000BASE-X SFP transceiver in

the tgigaethernet 0/1,thefollowingcommandcongurationisrequired:

Switch#cong

Switch_cong#interface tgigaethernet 0/1

Switch_cong_tg1/1#speed 1000

Switch_cong_tg1/1#exit

Switch_cong#interface range tgigaethernet 0/2-24

Switch_cong_if_range#speed 1000

Switch_cong_if_range#

Figure 4-6 Setting 1000BASE-X Screen

4.4 Setting40GBASE-Xfor100GSFP+Port

The Managed Switch supports both 40GBASE-X and 100GBASE-X SFP

transceiversbymanual settingand the defaultSFP+ portspeed isset to100Gbps.

For example, to establish the ber connection with 40GBASE-X SFP transceiver in

the cgigaethernet 0/1,thefollowingcommandcongurationisrequired:

Switch#cong

Switch_cong#interface cgigaethernet 0/1

Switch_cong_cg0/1#speed 40000

Switch_cong_cg0/1#exit

Switch_cong#interface range cgigaethernet 0/2-4

Switch_cong_if_range#speed 40000

Switch_cong_if_range#

Figure 4-7 Setting 40GBASE-X Screen

4.5 Changing Password

The default password of the switch is “admin”. For security reason, it is

recommended to change password and the following command conguration is

required:

Switch#cong

Switch_cong#username admin password planet2018

Switch_cong#

Figure 4-8 Changing Password Interface Screen

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Planet

Planet

Planet FGSW-1820CS Manual de usuario

Planet

Planet IGS-4215-4P4Tv2 Manual de usuario

Planet

Planet POE-2400G Manual de usuario

Planet

Planet IGS-6325-8T4X Manual de usuario

Planet

Planet NOVASwitch Series Manual de usuario

Planet

Planet FSD-1600 Manual de usuario

Planet

Planet FSD-1604 Manual de usuario

Planet

Planet VC-820M Manual de usuario

Planet

Planet HPOE-1200G Manual de usuario

Planet

Planet IGS-5225-8P4S-12V Manual de usuario

Planet

Planet HPOE-460 Manual de usuario

Planet

Planet MGS-5220-8P2X Manual de usuario

Planet

Planet FSD-808HP Manual de usuario

Planet

Planet FGSW-2620VM Series Manual de usuario

Planet

Planet FSD-805 Manual de usuario

Planet

Planet NOVASwitch FNSW-8086F Manual de usuario

Planet

Planet XGS-5240-24X2QR Manual de usuario

Planet

Planet ISW-800T-M12 Manual de usuario

Planet

Planet IGSW-24040T Manual de usuario

Planet

Planet FSD-504PE Manual de usuario

Planet

Planet IFGS-1022HPT Manual de usuario

Planet

Planet WGSW-2840 Manual de usuario

Planet

Planet SGS-6341-24T4X Manual de usuario

Planet

Planet WGSW-14020 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario