Planet IFGS-1022HPT Manual de usuario

Industrial 8-Port 10/100TX 802.3at PoE+

+ 2-Port Gigabit TP/SFP Combo Ethernet Switch

IFGS-1022HPT

User’s Manual

Table of Contents

1. Package Contents........................................................................................ 3

2. Hardware Introduction ................................................................................. 4

2.1 Physical Dimensions .............................................................................. 4

2.2 Switch Front Panel ................................................................................ 5

2.3 LED Indicators ...................................................................................... 7

2.4 Switch Upper Panel ............................................................................... 8

2.5 Wiring the Power Inputs ........................................................................ 8

2.6 Wiring the Fault Alarm Contact............................................................... 9

2.7 Product Features..................................................................................10

2.8 ProductSpecications...........................................................................11

3. Installation ................................................................................................14

3.1 DIN-rail Mounting Installation................................................................14

3.2 Wall-mount Plate Mounting ...................................................................16

3.3 Installing the SFP Transceiver................................................................17

3.4 Removing the Transceiver Module..........................................................18

4. Troubleshooting..........................................................................................19

APPENDIX A: Networking Connection................................................................20

A.1 PoE RJ45 Port Pin Assignments (End-span).............................................20

A.2 Switch’s RJ45 Pin Assignments ..............................................................20

A.3 RJ45 Cable Pin Assignments..................................................................21

A.4 Fiber Optic Cable Connection Parameter .................................................22

APPENDIX B: Approved PLANET SFP Transceivers ..............................................23

1. Package Contents

Thank you for purchasing PLANET industrial 8-Port 10/100TX 802.3at PoE+ + 2-Port

Gigabit TP/SFP combo Ethernet Switch, IFGS-1022HPT. In the following section, the

term “Industrial PoE+ Switch” means the IFGS-1022HPT.

Open the box of the Industrial PoE+ Switch and carefully unpack it. The box

should contain the following items:

Industrial PoE+ Switch x 1 User’s Manual x 1

DIN Rail Kit x 1 Wall-mount Kit x 1

If any of these are missing or damaged, please contact your dealer immediately;

if possible, retain the carton including the original packing material, and use them

again to repack the product in case there is a need to return it to us for repair.

2. Hardware Introduction

2.1 Physical Dimensions

Dimensions (W x D x H): 161 x 107 x 72mm

Side View

Front View

Dimensions ( unit = mm )

Side View

Top View

Bottom View

Input DC 48V~56V

DC1 DC2

Fault

1A@24V

IFGS-1022HPT

P1 P2 FAULT

Extended Standard

910

LNK

PoE In-Use

ACT

802.3at PoE+

109

Long Reach Mode

ACT

1000

LNK

4 5 6 7 8

DIP ON

2.2 Switch Front Panel

The front panel of the Industrial PoE+ Switch consists of 8 10/100/BASE-TX ports

featuring 30-watt 802.3at PoE+, and 2 additional Gigabit copper/SFP combo

interfaces for Gigabit Ethernet extension and video uplink. The LED indicators are

also located on the front panel of the Industrial PoE+ Switch.

Figure 2-1 shows the front panel of Industrial PoE+ Switch.

IFGS-1022HPT

P1 P2 FAULT

Extended Standard

910

LNK

PoE In-Use

ACT

802.3at PoE+

109

Long Reach Mode

ACT

1000

LNK

4 5 6 7 8

DIP ON

Figure 2-1: IFGS-1022HPT Front Panel

Fast Ethernet TP interfaces (Port 1 to port 8)

10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.

Gigabit TP Interfaces (Port 9 to port 10 TP/SFP Combo Interfaces)

10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters.

Gigabit SFP Slots (Port 9 to port 10 TP/SFP Combo Interfaces)

1000BASE-SX/LX mini-GBIC slot, SFP (Small Factor Pluggable) transceiver

module:From550meters(multi-modeber)to10/20/30/40/50/60/70/120kilo-

meters(single-mode ber).

DIP Switch

The Industrial PoE+ Switch has a built-in solid DIP switch that provides

“Standard” and “Extend” operation modes. The Industrial PoE+ Switch operates

as a normal IEEE 802.af/at PoE+ Switch in the “Standard” operation mode.

In the “Extend” operation mode, the Industrial PoE+ Switch operates on a per-

port basis at 10Mbps full duplex operation but can support 30-watt PoE power

output over a distance of up to 250 meters overcoming the 100m limit on Ethernet

UTP cable. With this brand-new feature, the Industrial PoE+ Switch provides an

additional solution for 802.3af/at PoE+ distance extension.

Default PoE Mode

PoE IP

Camera

PoE

100 meters (328 feet)

PoE

100BASE-TX UTP with PoE

P1 P2 FAULT

Extended Standard

Long Reach Mode

4 5 6 7 8

DIP ON

Extended PoE Mode

PoE IP

Camera

PoE

250 meters (820 feet)

P1 P2 FAULT

Extended Standard

Long Reach Mode

4 5 6 7 8

DIP ON

2.3 LED Indicators

System

LED Color Function

P1 Green Lit: indicates power 1 has power.

P2 Green Lit: indicates power 2 has power.

FAULT Red Lit: indicates neither power 1 or power 2 has no power.

Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1 to Port 8)

LED Color Function

LNK/

ACT Green

Lit: indicates the link through that port is successfully

established at 10Mbps or 100Mbps.

Blinking: indicates that the switch is actively sending or

receiving data over that port.

PoE

In-Use Orange

Lit: indicates the port is providing DC in-line power.

Off: indicates the connected device is not a PoE powered device

(PD).

Per 10/100/1000BASE-T Interface (Shared with Port 9 to Port 10)

LED Color Function

LNK/

ACT Green

Lit: indicates the link through that port is successfully

established at 10/100/1000Mbps.

Blinking: indicates that the switch is actively sending or

receiving data over that port.

1000 Orange

Lit: indicates the link through that port is successfully

established at 1000Mbps.

Off: indicates the link through that port is successfully

established at 10/100Mbps.

Per 1000X SFP Slot (Shared with Port 9 to Port 10)

LED Color Function

LNK/

ACT Green

Lit: indicates the link through that port is successfully

established at 1000Mbps.

Blinking: indicates that the switch is actively sending or

receiving data over that port.

1000 Orange

Lit: indicates the link through that port is successfully

established at 1000Mbps.

Off: indicates the link through that port is not established.

2.4 Switch Upper Panel

The upper panel of the Industrial PoE+ Switch consists of one terminal block

connector within two DC power inputs.

Figure 2-2 shows the upper panel of the Industrial PoE+ Switch.

Input DC 48V~56V

DC1 DC2

Fault

1A@24V

1 2 3 4 5 6

Figure 2-2: Industrial PoE+ Switch Upper Panel

2.5 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Industrial PoE+ Switch

is used for two DC redundant power inputs. Please follow the steps below to insert

the power wire.

When performing any of the procedures like inserting the wires or

tightening the wire-clamp screws, make sure the power is OFF to

prevent from getting an electric shock.

1. Insert positive and negative DC power wires into contacts 1 and 2 for POWER 1,

or 5 and 6 for POWER 2.

Input DC 48V~56V

DC1 DC2

Fault

1A@24V

1 2 3 4 5 6

2. Tighten the wire-clamp screws for preventing the wires from loosening.

1 2 3 4 5 6

Power 1 Fault Power 2

+ - + -

Note

1. The wire gauge for the terminal block should be in the range

between 12 and 24 AWG.

2. The DC power input range is 48V ~ 56V DC.

2.6 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block connector as the

picture shows below. Inserting the wires, the Industrial PoE+ Switch will detect

the fault status of the power failure and then forms an open circuit. The following

illustration shows an application example for wiring the fault alarm contacts.

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1. The wire gauge for the terminal block should be in the range

between 12 and 24 AWG.

2. Alarm relay circuit accepts up to 30V, max. 3A currents.

2.7 Product Features

Physical Port

Eight 10/100BASE-TX Fast Ethernet RJ45 ports with IEEE 802.3at/af

PoE+ Injector (Port-1 to Port-8)

Two 10/100/1000BASE-T Gigabit Ethernet RJ45 ports (Port-9 and Port-10)

Two 1000BASE-X mini-GBIC/SFP slots for SFP type auto detection (Port-9

and Port-10)

Power over Ethernet

Complies with IEEE 802.3at Power over Ethernet Plus, end-span PSE

Backward compatible with IEEE 802.3af Power over Ethernet

Up to 8 ports of IEEE 802.3af/802.3at devices powered

240-watt PoE budget

Supports PoE power up to 30 watts for each PoE port

Auto detects powered device (PD)

Circuit protection prevents power interference between ports

Remote power feeding up to 100 meters

Industrial Case and Installation

IP30 metal case

DIN rail and wall-mount design

48~56V DC, redundant power with polarity reverse protect function

Supports 6000V DC Ethernet ESD protection

-40 to 75 degrees C operating temperature

Switching

Hardware-based 10/100Mbps (half/full duplex), 1000Mbps (full duplex), auto-

negotiation and auto MDI/MDI-X

Features Store-and-Forward mode with wire-speed ltering and forwarding

rates

IEEE 802.3x ow control for full duplex operation and back pressure for half

duplex operation

16K MAC address table size

10K jumbo frame

IEEE 802.1Q VLAN transparency

Hardware DIP switch for “Standard” and “Extend” mode selection; the

“Extend” mode features 30-watt PoE transmit distance of 250m at speed of

10Mbps

Automatic address learning and address aging

Supports CSMA/CD protocol

Otros manuales para IFGS-1022HPT

Tabla de contenidos

Otros manuales de Cambiar de Planet

Planet

Planet MII Series Manual de usuario

Planet

Planet WGSD-1022 Manual de usuario

Planet

Planet KVM-810 Manual de usuario

Planet

Planet GS-5220-8UP2T2X Manual de usuario

Planet

Planet IGS-4215 Series Manual de usuario

Planet

Planet ISW-800T-M12 Manual de usuario

Planet

Planet IGS-5227-4MP2MT Manual de usuario

Planet

Planet XGS3-24042 Manual de usuario

Planet

Planet WGSW-14020 Manual de usuario

Planet

Planet FGSW-2022VHP Manual de usuario

Planet

Planet WGSW-52040 Manual de usuario

Planet

Planet GSD-1603 Manual de usuario

Planet

Planet IFB-244-SLC Manual de usuario

Planet

Planet KVM-U201 Manual de usuario

Planet

Planet GSW-1601 Manual de usuario

Planet

Planet ISW-511 Series Manual de usuario

Planet

Planet WGSW-24040 Manual de usuario

Planet

Planet IDL-2402 Manual de usuario

Planet

Planet FSD-1600 Manual de usuario

Planet

Planet PL-401E Manual de usuario

Planet

Planet FSD-1603 Manual de usuario

Planet

Planet IPOE-470 Manual de usuario

Planet

Planet FGSW-2612PVS Manual de usuario

Planet

Planet NOVASwitch FNSW-8086F Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario