Planet SGS-6341-24T4X Manual de usuario
L3 Multi-Port Full Gigabit Stackable Managed Switch
SGS-6341-24T4X/SGS-6341-24P4X/
SGS-6341-48T4X/SGS-6341-16S8C4XR
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Switch Management.................................................................................... 4
3. Requirements ............................................................................................. 5
4. Terminal Setup ........................................................................................... 6
4.1 Logon to the Console........................................................................... 7
4.2 ConguringIPAddress......................................................................... 7
4.3 Setting1000BASE-XforSFP+Port........................................................ 9
4.4 SavingtheConguration ...................................................................... 9
5. Starting Web Management .........................................................................10
5.1LoggingintotheManagedSwitch.........................................................11
5.2SavingCongurationviatheWeb..........................................................13
6. RecoveringBacktoDefaultConguration.....................................................14
7. Customer Support .....................................................................................16
3
1. Package Contents
Thank you for purchasing PLANET L3 Multi-Port Full Gigabit Stackable Managed
Switch, SGS-6341-24T4X/SGS-6341-24P4X/SGS-6341-48T4X/SGS-6341-16S8C4XR.
Thedescriptionsofthesemodelsareasfollows:
SGS-6341-24T4X Layer324-Port10/100/1000T+4-Port10GSFP+
StackableManagedSwitch
SGS-6341-24P4X Layer324-Port10/100/1000T802.3atPoE+4-Port
10GSFP+StackableManagedSwitch(370W)
SGS-6341-48T4X Layer348-Port10/100/1000T+4-Port10GSFP+
StackableManagedSwitch
SGS-6341-16S8C4XR
Layer316-Port100/1000XSFP+8-PortGigabitTP/
SFP+4-Port10GSFP+StackableManagedSwitch
(100~240VAC,12VDC)
Unless specied, “Managed Switch” mentioned in this Quick Installation Guide
referstotheabovethreemodels.
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zTheManagedSwitchx1
zQuickInstallationGuidex1
zRJ45-to-DB9ConsoleCablex1
zPowerCordx1
zGroundingCablex1
zRubberFeetx4
zTwoRack-mountingBracketswithAttachmentScrewsx1
zSFPDustCap
Model SFPDust-proofCaps
SGS-6341-24T4X 4
SGS-6341-24P4X 8
SGS-6341-48T4X 4
SGS-6341-16S8C4XR 28
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Switch Management
To set up the Managed Switch, the user needs to congure the Managed Switch
fornetwork management.The ManagedSwitch providestwo managementoptions:
Out-of-Band Management and In-Band Management.
Out-of-Band Management
Out-of-band management is the management through Console interface.
Generally, the user will use out-of-band management for the initial switch
conguration,orwhenin-bandmanagementisnotavailable.
Important
TheManagedSwitchisshippedwithIPaddress(192.168.0.254/24)
assigned by default. User can assign another IP address to the
Managed Switch via the Console interface to be able to remotely
accesstheManagedSwitchthroughTelnetorHTTP.
In-Band Management
In-band management refers to the management by logging in to the Managed
Switchusing Telnetor HTTP, orusing SNMPmanagement softwaretocongure the
Managed Switch. In-band management enables the management of the Managed
SwitchtoattachsomedevicestotheSwitch.Thefollowing proceduresarerequired
toenableIn-bandmanagement:
1. Logon to console
2.Assign/CongureIPaddress
3. Create a remote login account
4.EnableHTTPorTelnetserverontheManagedSwitch
In case in-band management fails due to Managed Switch conguration changes,
out-of-band management can be used for conguring and managing the Managed
Switch
5
3. Requirements
zWorkstations running Windows XP/2003/Vista/7/8/2008/10, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerial Port Connection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such as
Tera Term or PuTTY.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedSwitch.
zEthernet Port Connection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.
6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to serial (console) port of the Managed Switch. The
console port of the Managed Switch is DCE already, so that you can connect the
consoleportdirectlythroughPCwithouttheneedofNullModem.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch. Tera Term program may be a good choice. The Tera Term can be accessed
fromtheStart menu.
1. Click START menu, then Programs,andthenTera Term.
2.When the following screen appears, make sure that the COM port should be
conguredas:
zBaud:115200
zParity:None
zDatabits:8
zStopbits:1
zFlowcontrol:None
Figure 4-2 Tera Term COM Port Conguration
7
4.1 Logon to the Console
Once the terminal is connected to the device, power on the Managed Switch, and
theterminalwilldisplay“running testing procedures”.
Then, the following message asks for the login user name and password. The
factory default user name and password are as follows as the login screen in
Figure4-3appears.
Username:admin
Password:admin
Figure 4-3 Managed Switch Console Login Screen
The user can now enter commands to manage the Switch. For a detailed descrip-
tionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new
passwordafterthisfirstsetup.
2.Only accept command in lowercase letter under console inter-
face.
4.2 ConguringIPAddress
The IP address conguration commands for VLAN1 interface are listed below.
Before using in-band management, the Managed Switch must be congured with
an IP address by out-of-band management (i.e. console mode). The conguration
commandsareasfollows:
SGS-6341-Series# cong
SGS-6341-Series(cong)# interface vlan 1
SGS-6341-Series(cong-if-Vlan1)# ip address 192.168.1.254 255.255.255.0
8
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IPv4 Address: 192.168.1.254
Subnet Mask: 255.255.255.0
Figure 4-4 Conguring IPv4 Address Screen
To check the current IP address or modify a new IP address for the Managed
Switch,pleaseusetheprocedureasfollows:
Show the current IP address
1. On “SGS-6341-Series#” prompt, enter “show ip interface brief”.
2.The screen displays the current IP address, subnet mask and gateway as shown
inFigure4-5.
Figure 4-5 Showing IP Information Screen
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of Managed Switch
throughthenewIPaddress.
Note
Ifyouarenotfamiliarwithconsolecommandortherelatedparam-
eter, enter “help”anytimeinconsoletogetthehelpdescription.
9
4.3 Setting1000BASE-XforSFP+Port
TheManagedSwitch supportsboth1000BASE-Xand 10GBASE-XSFPtransceiver
bymanual settingand thedefault SFP+port speedis setto 10Gbps.Forexample,
to establish the ber connection with 1000BASE-X SFP transceiver in the Ethernet
1/0/25,thefollowingcommandcongurationisrequired:
SGS-6341-Series#cong
SGS-6341-Series(cong)#interface ethernet 1/0/25
SGS-6341-Series(cong-if-ethernet1/0/25)#speed-duplex force1g-full
Figure 4-6 Setting 1000BASE-X Screen
4.4 SavingtheConguration
In Managed Switch, the running conguration le stores in the RAM. In the
current version, the running conguration sequence running-cong can be saved
from the RAM to FLASH by write command or copy running-cong startup-
congcommand,sothattherunning congurationsequencebecomesthe start-up
congurationle,whichiscalledcongurationsave.
SGS-6341-Series# copy running-cong startup-cong
SGS-6341-Series# write
Figure 4-7 Copying Running-cong Startup-cong Screen
10
5. Starting Web Management
The Managed Switch provides a built-in browser interface. You can manage it
remotely by having a remote host with Web browser, such as Microsoft Internet
Explorer,MozillaFirefox,GoogleChromeorAppleSafari.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address:
192.168.0.254
Figure 5-1 IP Management Diagram
The following shows how to start up the Web Management of the Managed
Switch. Please note the Managed Switch is congured through an Ethernet
connection. Please make sure the manager PC must be set to the same IP subnet
address.
For example, the IP address of the Managed Switch is congured with
192.168.0.254, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 253, except 254), and the default subnet mask is
255.255.255.0.
Thefactorydefaultusernameandpasswordareasfollows:
DefaultIP:192.168.0.254
Username:admin
Password:admin
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Cambiar de Planet
Planet
Planet WSD-800 Manual de usuario
Planet
Planet POE-1200 Manual de usuario
Planet
Planet SGSD-1022 Manual de usuario
Planet
Planet WGSW-2620HP Manual de usuario
Planet
Planet WGSW-2840 Manual de usuario
Planet
Planet WGSW-24000 Manual de usuario
Planet
Planet FNSW-1601 Manual de usuario
Planet
Planet SGS-6341 Series Instrucciones de instalación
Planet
Planet GSD-808HP Manual de usuario
Planet
Planet gsw-1820vhp Manual de usuario
Planet
Planet GSW-4804SF Manual de usuario
Planet
Planet WGSD-1022 Manual de usuario
Planet
Planet ISW-808PT-M12 Manual de usuario
Planet
Planet GS-4210 SERIES Manual de usuario
Planet
Planet FSD-808P Manual de usuario
Planet
Planet FGSD-1008HPS Manual de usuario
Planet
Planet WGSW-5240 Manual de usuario
Planet
Planet IPM-8221 Manual de usuario
Planet
Planet GS-5220-16S8CR Manual de usuario
Planet
Planet IGS-10020PT Manual de usuario
