Pilz PSSu E AI SHT2 Manual de usuario
PSSu E AI SHT2
Operating Manual 1003113-EN-02
}Decentralised system PSSuniversal I/O
Preface
This document is a translation of the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes. Suggestions and comments for improving this documentation will be
gratefully received.
Source code from third-party manufacturers or open source software has been used for
some components. The relevant licence information is available on the Internet on the Pilz
homepage.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital
Contents
Operating Manual PSSu E AI SHT2
1003113-EN-02 3
Section 1 Introduction 4
1.1 Validity of documentation 4
1.1.1 Retaining the documentation 4
1.1.2 Terminology: System environment A and B 4
1.2 Definition of symbols 5
Section 2 Overview 6
2.1 Module structure 6
2.2 Module features 6
2.3 Front view 7
Section 3 Safety 9
3.1 Intended use 9
3.2 Safety regulations 10
3.2.1 Use of qualified personnel 10
3.2.2 Warranty and liability 10
3.2.3 Disposal 10
Section 4 Function Description 11
4.1 Block diagram 11
4.2 Module features 11
4.2.1 Functions 11
Section 5 Installation 13
5.1 General installation guidelines 13
5.1.1 Dimensions 13
5.2 Installing the base module 14
5.3 Inserting and removing an electronic module 15
5.3.1 Inserting an electronic module 16
5.3.2 Removing an electronic module 17
5.3.3 Changing an electronic module during operation 17
Section 6 Wiring 18
6.1 General wiring guidelines 18
6.1.1 Mechanical connection of the base modules 18
6.2 Terminal configuration 20
6.3 Connecting the module 23
Section 7 Technical details 24
Section 8 Order reference 26
8.1 Product 26
8.2 Accessories 26
Introduction
Operating Manual PSSu E AI SHT2
1003113-EN-02 4
1 Introduction
1.1 Validity of documentation
This documentation is valid for the product type E AI SHT2. It is valid until new documenta-
tion is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
1.1.1 Retaining the documentation
This documentation is intended for instruction and should be retained for future reference.
1.1.2 Terminology: System environment A and B
The PSSu system can be used in two different system environments. The module's applic-
ation area is described in the chapter "Intended Use" of the manual.
The distinction is made between
}PSSu in system environment A
}PSSu in system environment B
The distinction is based on the application area of the PSSu system.
PSSu in system environment A may be used in the
}Decentralised system PSSu I/O
}Not in the automation system PSS 4000
PSSu in system environment B may be used in the
}Automation system PSS 4000, e.g. with
– Decentralised system PSSu I/O with SafetyNET p
– Control system PSSu PLC
– Control system PSSu multi
Introduction
Operating Manual PSSu E AI SHT2
1003113-EN-02 5
1.2 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Overview
Operating Manual PSSu E AI SHT2
1003113-EN-02 6
2 Overview
2.1 Module structure
A module consists of
}Electronic module and
}Base module with
– Screw terminals or
– Cage clamp terminals
The base modules are the carrier units for the electronic modules and are used to connect
the field wiring. The electronic modules are inserted on to the base modules and determine
the module's function.
Details of the base modules that can be used are available in the chapter entitled “Intended
Use”.
2.2 Module features
The product has the following features:
}1 analogue current input
Current range:
0 ... 0.2 A, single-pole, referenced to earth
}2 analogue current outputs
Current range:
0 .. 20mA, single-pole, referenced to earth
– Scaling of input current 1:10 and 1:20
– Evaluation via analogue input module with an input resistance = 115Ohm, (e.g.
PSSuEFAI I), order no.: 312 260)
}For standard and failsafe applications in system environment A and B
Overview
Operating Manual PSSu E AI SHT2
1003113-EN-02 7
2.3 Front view
2
2
Legend:
}A: Electronic module
}B: Base module
}1: Labelling strip with:
– Name of electronic module
– Order number
– Serial number
– Hardware version number
– 2D code
}2: Labelling strip for the terminal configuration on the base module
}3: Name of electronic module
}4: Connection level 1
}5: Connection level 2
}6: Connection level 3
}7: Connection level 4
Overview
Operating Manual PSSu E AI SHT2
1003113-EN-02 8
}8: Square mounting holes (connection levels 1, 2, 3 and 4)
– With screw to loosen/tighten the screw terminal on base modules with screw termin-
als
– With mechanism to operate the cage clamp on base modules with cage clamp ter-
minals
}9: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal
lines
}10: Mounting slot for colour marker to label the connection level (connection levels 1, 2,
3 and 4)
Safety
Operating Manual PSSu E AI SHT2
1003113-EN-02 9
3 Safety
3.1 Intended use
The module provides shunts to scale the current for analogue inputs. The module may be
used in conjunction with analogue current inputs (e.g. PSSuEFAII, order no.: 312 260).
The module may be used for standard applications in system environment A and B.
Intended use includes making the electrical installation EMC-compliant. Please refer to the
guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use
in an industrial environment. It is not suitable for use in a domestic environment, as this can
lead to interference.
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the module
}Use of the module outside the areas described in this manual
}Any use of the module that is not in accordance with the technical details.
The E AI SHT2 module may be used in conjunction with the following base modules:
}PSSu BP 1/8 S
}PSSu BP 1/8 C
}PSSu BP 1/12 S
}PSSu BP 1/12 C
}PSSu BP-C 1/8 S
}PSSu BP-C 1/8 C
}PSSu BP-C 1/12 S
}PSSu BP-C 1/12 C
Safety
Operating Manual PSSu E AI SHT2
1003113-EN-02 10
3.2 Safety regulations
3.2.1 Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by competent persons.
A competent person is someone who, because of their training, experience and current pro-
fessional activity, has the specialist knowledge required to test, assess and operate the
work equipment, devices, systems, plant and machinery in accordance with the general
standards and guidelines for safety technology.
It is the company’s responsibility only to employ personnel who:
}Are familiar with the basic regulations concerning health and safety / accident preven-
tion
}Have read and understood the information provided in this description under "Safety"
}And have a good knowledge of the generic and specialist standards applicable to the
specific application.
3.2.2 Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended
}Damage can be attributed to not having followed the guidelines in the manual
}Operating personnel are not suitably qualified
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
3.2.3 Disposal
}In safety-related applications, please comply with the mission time TM in the safety-re-
lated characteristic data.
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Unidad de control de Pilz
Pilz
Pilz PIT si1.1 Manual de usuario
Pilz
Pilz PNOZ m EF 4DI4DOR Manual de usuario
Pilz
Pilz PZE 9P Manual de usuario
Pilz
Pilz PNOZ mc2.1p Manual de usuario
Pilz
Pilz PNOZ m ES Profibus Manual de usuario
Pilz
Pilz PSSu E S 2AI RTD Manual de usuario
Pilz
Pilz PNOZ mo2p Manual de usuario
Pilz
Pilz PNOZ mc7p Manual de usuario
Pilz
Pilz PSSu E PD1-T Manual de usuario
Pilz
Pilz PSEN ma1.4-51 M12/8-0.15m Manual de usuario
Pilz
Pilz PNOZ m0p Manual de usuario
Pilz
Pilz PNOZ mi1p Manual de usuario
Pilz
Pilz PNOZ mmc4p Manual de usuario
Pilz
Pilz PRBT 6 Manual de usuario
Pilz
Pilz PSSu E F 2DO 2 Manual de usuario
Pilz
Pilz PSEN cs 4.2p/M12 Manual de usuario
Pilz
Pilz PIT es Set10u-5c PCB Manual de usuario
Pilz
Pilz PNOZ mo1p Manual de usuario
Pilz
Pilz PNOZ mc3p Manual de usuario
Pilz
Pilz PDP67 F 8DI ION Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
