Pilz PSSu E S 2AI RTD Manual de usuario

PSSu E S 2AI RTD(-T)

Operating Manual 22017-EN-07

}Decentralised system PSSuniversal I/O

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PSSu E S 2AI RTD(-T)

22017-EN-07 3

Section 1 Introduction 5

1.1 Validity of documentation 5

1.1.1 Retaining the documentation 5

1.1.2 Terminology: System environment A and B 5

1.2 Definition of symbols 6

Section 2 Overview 7

2.1 Module structure 7

2.2 Module features 7

2.3 Front view 8

Section 3 Safety 10

3.1 Intended use 10

3.2 Safety regulations 11

3.2.1 Use of qualified personnel 11

3.2.2 Warranty and liability 11

3.2.3 Disposal 11

Section 4 Function description 12

4.1 Block diagram 12

4.2 Module features 12

4.2.1 Integrated protection mechanisms 12

4.2.2 Functions 12

4.3 Configuration 13

4.3.1 Measuring ranges 13

4.3.2 Connection type 14

4.3.3 Range monitoring 14

4.3.4 Offset for the 2-wire measurement 14

4.3.5 Digital filter 15

4.3.6 Scaling 16

4.3.6.1 ADC raw value 17

4.3.6.2 Manufacturer scaling 17

4.3.6.3 User scaling 17

4.3.6.4 Values that fall outside the range limits 18

4.3.7 Data formats 18

4.3.8 Summary and overview 19

4.3.9 PSSu assignment in system environment A 20

4.3.9.1 Status byte 21

4.3.10 PSSu assignment in system environment B 21

Section 5 Installation 22

5.1 General installation guidelines 22

5.1.1 Dimensions 22

5.2 Installing the base module 23

5.3 Inserting and removing an electronic module 24

5.3.1 Inserting an electronic module 25

5.3.2 Removing an electronic module 26

Contents

Operating Manual PSSu E S 2AI RTD(-T)

22017-EN-07 4

5.3.3 Changing an electronic module during operation 26

Section 6 Wiring 27

6.1 General wiring guidelines 27

6.1.1 Mechanical connection of the base modules 27

6.2 Terminal configuration 29

6.3 Connecting the module 31

Section 7 Operation 33

7.1 Messages 33

7.2 Display elements 33

7.2.1 Display elements for module diagnostics 33

7.2.2 Displaying the input status 34

Section 8 Technical Details 35

Section 9 Order reference 39

9.1 Product 39

9.2 Accessories 39

Introduction

Operating Manual PSSu E S 2AI RTD(-T)

22017-EN-07 5

1 Introduction

1.1 Validity of documentation

This documentation is valid for the products PSSu E S 2AI RTD and PSSu E S 2AI RTD-T.

It is valid until new documentation is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

The module PSSu E S 2AI RTD-T is suitable for use where there are increased environ-

mental requirements (see Technical Details).

1.1.1 Retaining the documentation

This documentation is intended for instruction and should be retained for future reference.

1.1.2 Terminology: System environment A and B

The PSSu system can be used in two different system environments. The module's applic-

ation area is described in the chapter "Intended Use" of the manual.

The distinction is made between

}PSSu in system environment A

}PSSu in system environment B

The distinction is based on the application area of the PSSu system.

PSSu in system environment A may be used in the

}Decentralised system PSSu I/O

}Not in the automation system PSS 4000

PSSu in system environment B may be used in the

}Automation system PSS 4000, e.g. with

– Decentralised system PSSu I/O with SafetyNET p

– Control system PSSu PLC

– Control system PSSu multi

Introduction

Operating Manual PSSu E S 2AI RTD(-T)

22017-EN-07 6

1.2 Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Overview

Operating Manual PSSu E S 2AI RTD(-T)

22017-EN-07 7

2 Overview

2.1 Module structure

A module consists of

}Electronic module and

}Base module with

– Screw terminals or

– Cage clamp terminals

The base modules are the carrier units for the electronic modules and are used to connect

the field wiring. The electronic modules are inserted on to the base modules and determine

the module's function.

Details of the base modules that can be used are available in the chapter entitled “Intended

Use”.

2.2 Module features

The product has the following features:

}Analogue ST inputs: 2

}Type of inputs: Resistance thermometer

}Corresponding sensors (configurable):

– Pt100

– Pt200

– Pt500

– Pt1000

– Ni100

– Ni120

– Ni1000

}Resistance measurement (configurable):

– 0 ... 4000 Ohm

}Max. resolution:

– 0.0625 °C

– 0.0625 Ohm

}Open circuit detection

}LEDs for:

– Operating status per input

– Module error

}For standard applications in system environment A and B

}T-type:

PSSu E S 2AI RTD-T: for increased environmental requirements

Overview

Operating Manual PSSu E S 2AI RTD(-T)

22017-EN-07 8

2.3 Front view

PSSu E S

2AI RTD

312490

000000

001

I0 I1

PSSu E S

2AI RTD

R0+

R0-

(C)

R1+

R1-

(C)

RL0+

RL0-

(C)

RL1+

RL1-

(C)

Err

2111

2212

2313

2414

2616

2515

Legend:

}A: Electronic module

}B: Base module

}1: LED for module diagnostics

}2: Labelling strip with:

– Name of electronic module

– Order number

– Serial number

– Hardware version number

– 2D code

Overview

Operating Manual PSSu E S 2AI RTD(-T)

22017-EN-07 9

}3: Labelling strip for the terminal configuration on the base module

}4: Name of electronic module

}5: Connection level 1

}6: Connection level 2

}7: Connection level 3

}8: Connection level 4

}9: Connection level 5

}10: Connection level 6

}11: Square mounting holes (connection levels 1, 2, 3 and 4)

– With screw to loosen/tighten the screw terminal on base modules with screw termin-

als

– With mechanism to operate the cage clamp on base modules with cage clamp ter-

minals

}12: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal

lines

}13: Mounting slot for colour marker to label the connection level (connection levels 1, 2,

3 and 4)

Safety

Operating Manual PSSu E S 2AI RTD(-T)

22017-EN-07 10

3 Safety

3.1 Intended use

The module may be used for standard applications in system environment A and B.

The module provides analogue inputs. It may be used as an input module for standard

functions.

The modules PSSu E S 2AI RTD and PSSu E S 2AI RTD-T may be used as a safety com-

ponent in accordance with the Lifts Directive 95/16/EC, EN81-1, EN81-2 and EN115-1.

The programmable safety system should be installed in a protected environment that meets

at least the requirements of pollution degree 2. Example: Protected inside space or control

cabinet with protection class IP54 and corresponding air conditioning.

The module PSSu E S 2AI RTD-T is suitable for use where there are increased environ-

mental requirements (see Technical Details).

Intended use includes making the electrical installation EMC-compliant. Please refer to the

guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use

in an industrial environment. It is not suitable for use in a domestic environment, as this can

lead to interference.

The following is deemed improper use in particular:

}Any component, technical or electrical modification to the module

}Use of the module outside the areas described in this manual

}Any use of the module that is not in accordance with the technical details.

INFORMATION

The module is supported by:

}PSSuniversal Configurator and PSSuniversal Assistant from Version

1.6.0

}PAS4000 from version 1.8.0

– We recommend that you always use the latest version (download

from www.pilz.de).

The PSSu E S 2AI RTD module may be used in conjunction with the following base mod-

ules:

}PSSu BP 1/12 S

}PSSu BP 1/12 C

}PSSu BP-C 1/12 S

}PSSu BP-C 1/12 C

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Pilz

Pilz

Pilz PNOZ m ES ETH Manual de usuario

Pilz

Pilz PNOZ m0p Manual de usuario

Pilz

Pilz PNOZ m EF 1MM Manual de usuario

Pilz

Pilz PSEN ma1.3a/b-22 Manual de usuario

Pilz

Pilz PNOZ mc2.1p Manual de usuario

Pilz

Pilz PNOZ mc6p Manual de usuario

Pilz

Pilz PIT es Set10u-5c PCB Manual de usuario

Pilz

Pilz PSSu K S RS232 Modbus ASCII Manual de usuario

Pilz

Pilz PSS CPU Series Manual de usuario

Pilz

Pilz PRBT 6 Manual de usuario

Pilz

Pilz PIT gb Series Manual de usuario

Pilz

Pilz PNOZ mc10p Manual de usuario

Pilz

Pilz PNOZ po3.2p Manual de usuario

Pilz

Pilz PIT js2 Manual de usuario

Pilz

Pilz PNOZ m ES ETH Manual de usuario

Pilz

Pilz PNOZ mmc1p Manual de usuario

Pilz

Pilz PNOZ p1vp Manual de usuario

Pilz

Pilz PSSu K F FAU B Manual de usuario

Pilz

Pilz PNOZ m EF 4DI4DOR Manual de usuario

Pilz

Pilz PSSu K F EI Manual de usuario

Pilz

Pilz PSEN ma1.4n-51 Manual de usuario

Pilz

Pilz PNOZ m0p Manual de usuario

Pilz

Pilz PNOZmulti 2 Manual de usuario

Pilz

Pilz PNOZ mc4p Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario