Pilz PSEN ma1.4-51 M12/8-0.15m Manual de usuario
PSEN ma1.4-51 M12/8-0.15m
Operating Manual-22185-EN-05
}PSEN sensor technology
Preface
This document is a translation of the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes. Suggestions and comments for improving this documentation will be
gratefully received.
Source code from third-party manufacturers or open source software has been used for
some components. The relevant licence information is available on the Internet on the Pilz
homepage.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital
Contents
Operating Manual PSEN ma1.4-51 M12/8-0.15m
22185-EN-05 3
Introduction 4
Validity of documentation 4
Using the documentation 4
Definition of symbols 4
Safety 5
Intended use 5
Safety regulations 5
Safety assessment 5
Use of qualified personnel 6
Warranty and liability 6
Disposal 6
For your safety 6
Unit features 7
Function description 7
Block diagram 7
Operating distances 8
Lateral and vertical offset 8
Wiring 9
Pin assignment 9
Requirements and connection to evaluation devices 10
Installation 13
Installation type 1 14
Installation type 2 15
Adjustment 16
Periodic test 17
Dimensions in mm 17
Technical details 17
Safety characteristic data 19
Order reference 20
System 20
Accessories 20
EC declaration of conformity 20
PSEN ma1.4-51 M12/8-0.15m
Operating Manual PSEN ma1.4-51 M12/8-0.15m
22185-EN-05 4
Introduction
Validity of documentation
This documentation is valid for the product PSEN ma1.4-51 M12/8-0.15m. It is valid until
new documentation is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
Using the documentation
This document is intended for instruction. Only install and commission the product if you
have read and understood this document. The document should be retained for future ref-
erence.
Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.
PSEN ma1.4-51 M12/8-0.15m
Operating Manual PSEN ma1.4-51 M12/8-0.15m
22185-EN-05 5
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Safety
Intended use
The safety function of the safety switch is:
}Safe detection of the magnetic actuator within the response range
The safety switch meets the requirements in accordance with:
}EN 60947-5-3: PDDB only in connection
– with the operator PSEN ma1.4-03 or operator PSEN ma1.4-10 and
– the suitable evaluation devices (see Requirements and connection to evaluation
devices [ 10]).
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the product
}Use of the product outside the areas described in this manual
}Use of the product outside the technical details (see Technical details [ 17]).
NOTICE
EMC-compliant electrical installation
The product is designed for use in an industrial environment. The product
may cause interference if installed in other environments. If installed in other
environments, measures should be taken to comply with the applicable
standards and directives for the respective installation site with regard to in-
terference.
Safety regulations
Safety assessment
Before using a unit it is necessary to perform a safety assessment in accordance with the
Machinery Directive.
Functional safety is guaranteed for the product as a single component. However, this does
not guarantee the functional safety of the overall plant/machine. In order to achieve the re-
quired safety level for the overall plant/machine, define the safety requirements for the
plant/machine and then define how these must be implemented from a technical and organ-
isational standpoint.
PSEN ma1.4-51 M12/8-0.15m
Operating Manual PSEN ma1.4-51 M12/8-0.15m
22185-EN-05 6
Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by competent persons.
A competent person is a qualified and knowledgeable person who, because of their train-
ing, experience and current professional activity, has the specialist knowledge required. To
be able to inspect, assess and operate devices, systems and machines, the person has to
be informed of the state of the art and the applicable national, European and international
laws, directives and standards.
It is the company’s responsibility only to employ personnel who
}Are familiar with the basic regulations concerning health and safety / accident preven-
tion,
}Have read and understood the information provided in this description under "Safety"
}Have a good knowledge of the generic and specialist standards applicable to the spe-
cific application.
Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended
}Damage can be attributed to not having followed the guidelines in the manual
}Operating personnel are not suitably qualified
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
Disposal
}In safety-related applications, please comply with the mission time TM in the safety-re-
lated characteristic data.
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).
For your safety
WARNING!
Loss of safety function due to manipulation of the interlocking device
Manipulation of the interlocking device may lead to serious injury and death.
– You should prevent any possibility of the interlocking device being
manipulated through the use of a spare actuator.
– Keep the substitute actuator in a safe place and protect it from unau-
thorised access.
– If spare actuators are used, these must be installed as described in
Installation [ 13].
– If the original actuators are replaced with substitute actuators, the ori-
ginal actuators must be destroyed before disposal.
PSEN ma1.4-51 M12/8-0.15m
Operating Manual PSEN ma1.4-51 M12/8-0.15m
22185-EN-05 7
}Do not remove the connector's protective cap until you are just about to connect the
unit. This will prevent potential contamination.
Unit features
}The actuator PSEN ma1.4-03 or PSEN ma1.4-10 belongs to the safety switch.
}Coded actuator
}Safety switch with 8-pin M12 male connector
}2 safety contacts (reed contacts - N/O)
}1 auxiliary contact (N/O)
}Different operating distances depending on the actuator see Technical details [ 17]
}Design:
– Safety switch with square design
– Actuator with square design: PSEN ma1.4-03
– Actuator with square design: PSEN ma1.4-10
}Operation Magnetic
}Switching voltage 24 VDC
}LED to display switch status
Function description
If the actuator is within the response range (safety gate closed), the safety contacts and the
auxiliary contact on the safety switch will be closed and the LED will light.
Operate the PSEN ma1.4-51 M12/8-0.15m in conjunction with the following components:
}Actuator PSEN ma1.4-03 or actuator PSEN ma1.4-10 (see Order reference [ 20])
and
}a connected evaluation device (see Requirements and connection to evaluation
devices [ 10]).
Block diagram
7
1
4
2+
6
3
Actuator
Safety switch
Magnet
PSEN ma1.4-51 M12/8-0.15m
Operating Manual PSEN ma1.4-51 M12/8-0.15m
22185-EN-05 8
Operating distances
Sao SoSrSar (mm)Somin
On
Off
Legend
Sao Assured operating distance
Somin Min. operating distance
Sar Assured release distance
The offset-independent values for the switching distances are included in the Technical
details [ 17].
Lateral and vertical offset
[1] [2]
Legend
[1] Lateral offset
[2] Vertical offset
Actuator PSEN ma1.4-03
Assured operating distance Sao in mm
Vertical offset
Lateral offset
0 1 2 3 4
03.0 3.0 2.5 1.5 1.0
13.0 2.5 2.0 0.5 -
22.5 1.5 1.0 - -
31.5 0.5 - - -
40.5 - - - -
The stated values are valid at a temperature of 20 °C.
PSEN ma1.4-51 M12/8-0.15m
Operating Manual PSEN ma1.4-51 M12/8-0.15m
22185-EN-05 9
Actuator PSEN ma1.4-10
Assured operating distance Sao in mm
Vertical offset
Lateral offset
0 mm 2 mm 4 mm 6 mm 8 mm
0mm 10.0 10.0 9.0 7.0 5.0
2 mm 10.0 10.0 8.0 6.0 3.0
4 mm 9.0 8.0 7.0 5.0 -
6 mm 7.0 6.0 5.0 - -
The stated values are valid at a temperature of 20 °C.
Wiring
}Information given in the Technical details [ 17] must be followed.
}Calculation of the max. cable length lmax:
Rlmax - Ri
Rl / km
Imax =
Rlmax = Max. overall cable resistance (see evaluation device's technical details)
Ri = Internal resistance sensor (see Technical details [ 17])
Rl/km = Cable resistance/km of the cable (seetechnical details cable)
}Ensure the wiring and EMC requirements of EN 60204-1 are met.
}In the following cases, check the function that detects shorts across contacts prior to
commissioning:
– On evaluation devices with DC supply voltage: Overall cable resistance ≥ 15 Ohms
per channel
– On evaluation devices with AC supply voltage: Overall cable resistance ≥ 25 Ohms
per channel
– For details of how to perform the test for shorts across the contacts, please refer to
the operating manual for the relevant evaluation device.
Pin assignment
NOTICE
The colour marking for the connection lead only applies for the cable that
Pilz supplies as an accessory
The safety switch is shown in an unoperated condition.
PSEN ma1.4-51 M12/8-0.15m
Operating Manual PSEN ma1.4-51 M12/8-0.15m
22185-EN-05 10
Assignment of
the 8-pin con-
nector
pink
green
white
yellow
brown
blue
3
5
2+
4
6
1
7
8
grey
red
NC
NC
NOTICE
The auxiliary contact with LED
– May only be operated with a supply voltage of up to 24 VDC with
PNOZ X units
– May not be connected in series with PNOZ X, PNOZelog and
PNOZmulti units
– maynot be used for safety circuits
Requirements and connection to evaluation devices
For use of PSEN ma1.4-51 M12/8-0.15m in accordance with DIN EN 60947-5-3 an evalu-
ation device must be connected.
Connect the PSEN ma1.4-51 M12/8-0.15m
}either with a certified Pilz evaluation device
}or with an evaluation device with defined properties
Certified Pilz evaluation devices are, for example:
}PNOZelog for safety gate monitoring
– PNOZ e1p, PNOZ e1.1p, PNOZ e1vp
– PNOZ e5.11p
– PNOZ e6vp, PNOZ e6.1p
}PNOZpower for safety gate monitoring
– PNOZ p1p, PNOZ p1vp
}PNOZsigma for safety gate monitoring:
– PNOZ s3
– PNOZ s4
– PNOZ s5
}PNOZ X for safety gate monitoring
– PNOZ X2, PNOZ X2.5P, PNOZ X2.7P, PNOZ X2.8P, PNOZ X2.9P, PNOZX2C,
– PNOZ X3, PNOZ X3.1, PNOZ X3P, PNOZ X3.10P
– PNOZ X4
Otros manuales para PSEN ma1.4-51 M12/8-0.15m
1
Tabla de contenidos
Otros manuales de Unidad de control de Pilz
Pilz
Pilz PNOZ ms4p Manual de usuario
Pilz
Pilz PNOZ mi1p Manual de usuario
Pilz
Pilz ms3p HTL Manual de usuario
Pilz
Pilz PSS u2 ES 8DI Manual de usuario
Pilz
Pilz PSSu E F 4DO 0.5 Manual de usuario
Pilz
Pilz PSEN ma1.4n-51 Manual de usuario
Pilz
Pilz PNOZmulti 2 Manual de usuario
Pilz
Pilz PNOZ ma1p Manual de usuario
Pilz
Pilz PIT m3.3p Manual de usuario
Pilz
Pilz PNOZ m EF 16DI Manual de usuario
Pilz
Pilz PSS CPU Series Manual de usuario
Pilz
Pilz PNOZ s11 Manual de usuario
Pilz
Pilz PNOZ mi2p Manual de usuario
Pilz
Pilz PSS Series Manual de usuario
Pilz
Pilz PSSu E F PS2 Manual de usuario
Pilz
Pilz PNOZ mc12p Manual de usuario
Pilz
Pilz PNOZ p1vp Manual de usuario
Pilz
Pilz PNOZ po3.1p Manual de usuario
Pilz
Pilz PDP67 F 8DI ION Manual de usuario
Pilz
Pilz PNOZ m ES Powerlink Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
