Pilz PSSu E PD1-T Manual de usuario
PSSu E PD1(-T)
Operating Manual 21453-EN-04
}Decentralised system PSSuniversal I/O
Preface
This document is a translation of the original document.
All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made
for internal purposes. Suggestions and comments for improving this documentation will be
gratefully received.
Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,
SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks
of Pilz GmbH & Co. KG in some countries.
SD means Secure Digital
Contents
Operating Manual PSSu E PD1(-T)
21453-EN-04 3
Section 1 Introduction 4
1.1 Validity of documentation 4
1.1.1 Retaining the documentation 4
1.2 Definition of symbols 4
Section 2 Overview 6
2.1 Module structure 6
2.2 Module features 6
2.3 Front view 7
Section 3 Safety 9
3.1 Intended Use 9
3.2 Safety regulations 9
3.2.1 Use of qualified personnel 9
3.2.2 Warranty and liability 10
3.2.3 Disposal 10
Section 4 Function description 11
4.1 Block diagram 11
4.2 Module features 11
4.2.1 Functions 11
4.3 Configuration 11
4.3.1 Configuration 11
4.3.2 Addresses in the process image 11
Section 5 Installation 12
5.1 General installation guidelines 12
5.1.1 Dimensions 12
5.2 Installing the base module 13
5.3 Inserting and removing an electronic module 14
5.3.1 Inserting an electronic module 15
5.3.2 Removing an electronic module 16
5.3.3 Changing an electronic module during operation 16
Section 6 Wiring 17
6.1 General wiring guidelines 17
6.1.1 Mechanical connection of the base modules 17
6.2 Terminal configuration 19
Section 7 Operation 20
7.1 Messages and display elements 20
Section 8 Technical details 21
Section 9 Order reference 23
9.1 Product 23
9.2 Accessories 23
Introduction
Operating Manual PSSu E PD1(-T)
21453-EN-04 4
1 Introduction
1.1 Validity of documentation
This documentation is valid for the products PSSu E PD1 and PSSu E PD1-T. It is valid un-
til new documentation is published.
This operating manual explains the function and operation, describes the installation and
provides guidelines on how to connect the product.
1.1.1 Retaining the documentation
This documentation is intended for instruction and should be retained for future reference.
1.2 Definition of symbols
Information that is particularly important is identified as follows:
DANGER!
This warning must be heeded! It warns of a hazardous situation that poses
an immediate threat of serious injury and death and indicates preventive
measures that can be taken.
WARNING!
This warning must be heeded! It warns of a hazardous situation that could
lead to serious injury and death and indicates preventive measures that can
be taken.
CAUTION!
This refers to a hazard that can lead to a less serious or minor injury plus
material damage, and also provides information on preventive measures
that can be taken.
NOTICE
This describes a situation in which the product or devices could be dam-
aged and also provides information on preventive measures that can be
taken. It also highlights areas within the text that are of particular import-
ance.
Introduction
Operating Manual PSSu E PD1(-T)
21453-EN-04 5
INFORMATION
This gives advice on applications and provides information on special fea-
tures.
Overview
Operating Manual PSSu E PD1(-T)
21453-EN-04 6
2 Overview
2.1 Module structure
A module consists of
}Electronic module and
}Base module with
– Screw terminals or
– Cage clamp terminals
The base modules are the carrier units for the electronic modules and are used to connect
the field wiring. The electronic modules are inserted on to the base modules and determine
the module's function.
Details of the base modules that can be used are available in the chapter entitled “Intended
Use”.
2.2 Module features
The product has the following features:
}The module provides connections for external supplies.
}The external supplies are galvanically isolated from the module bus supplies.
}T-type:
PSSu E PD1-T: for increased environmental requirements
Overview
Operating Manual PSSu E PD1(-T)
21453-EN-04 7
2.3 Front view
2111
2212
2414
4131
4232
4434
PSSu E
PD1
2313 4333
12
P2
11
P1
13
P3
14
P4
22
P2
21
P1
23
P3
24
P4
32
P2
31
P1
33
P3
34
P4
42
P2
41
P1
43
P3
44
P4
PSSu E
PD1
312196
000000
001
10
1
3
49
8
5
6
7
2
A
B
Legend:
}A: Electronic module
}B: Base module
}1: Labelling strip with:
– Name of electronic module
– Order number
– Serial number
– Hardware version number
– 2D code
}2: Labelling strip for the terminal configuration on the base module
}3: Name of electronic module
}4: Connection level 1
}5: Connection level 2
}6: Connection level 3
}7: Connection level 4
Overview
Operating Manual PSSu E PD1(-T)
21453-EN-04 8
}8: Square mounting holes (connection levels 1, 2, 3 and 4)
– With screw to loosen/tighten the screw terminal on base modules with screw termin-
als
– With mechanism to operate the cage clamp on base modules with cage clamp ter-
minals
}9: Round connection holes (connection levels 1, 2, 3 and 4) for connecting the signal
lines
}10: Mounting slot for colour marker to label the connection level (connection levels 1, 2,
3 and 4)
Safety
Operating Manual PSSu E PD1(-T)
21453-EN-04 9
3 Safety
3.1 Intended Use
The module may be used to feed and extract external supplies to and from the connection
terminals.
The module PSSu E PD1-T is suitable for use where there are increased environmental re-
quirements (see Technical Details).
Intended use includes making the electrical installation EMC-compliant. Please refer to the
guidelines stated in the "PSSuniversal Installation Manual". The module is designed for use
in an industrial environment. It is not suitable for use in a domestic environment, as this can
lead to interference.
The following is deemed improper use in particular:
}Any component, technical or electrical modification to the module
}Use of the module outside the areas described in this manual
}Any use of the module that is not in accordance with the technical details.
INFORMATION
The module is supported by
}PSSuniversal Configurator and PSSuniversal Assistant from Version
1.4.0
}PAS4000 from Version 1.0.0
– We recommend that you always use the latest version (download
from www.pilz.de).
The PSSu E PD1 module may be used in conjunction with the following base modules:
}PSSu BP 2/16 S
}PSSu BP 2/16 C
}PSSu BP-C 2/16 S
}PSSu BP-C 2/16 C
The module PSSu E PD1-T may be used in conjunction with the following base modules:
}PSSu BP 2/16 S-T
}PSSu BP 2/16 C-T
}PSSu BP-C 2/16 S-T
}PSSu BP-C 2/16 C-T
3.2 Safety regulations
3.2.1 Use of qualified personnel
The products may only be assembled, installed, programmed, commissioned, operated,
maintained and decommissioned by competent persons.
Safety
Operating Manual PSSu E PD1(-T)
21453-EN-04 10
A competent person is someone who, because of their training, experience and current pro-
fessional activity, has the specialist knowledge required to test, assess and operate the
work equipment, devices, systems, plant and machinery in accordance with the general
standards and guidelines for safety technology.
It is the company’s responsibility only to employ personnel who:
}Are familiar with the basic regulations concerning health and safety / accident preven-
tion
}Have read and understood the information provided in this description under "Safety"
}And have a good knowledge of the generic and specialist standards applicable to the
specific application.
3.2.2 Warranty and liability
All claims to warranty and liability will be rendered invalid if
}The product was used contrary to the purpose for which it is intended
}Damage can be attributed to not having followed the guidelines in the manual
}Operating personnel are not suitably qualified
}Any type of modification has been made (e.g. exchanging components on the PCB
boards, soldering work etc.).
3.2.3 Disposal
}In safety-related applications, please comply with the mission time TM in the safety-re-
lated characteristic data.
}When decommissioning, please comply with local regulations regarding the disposal of
electronic devices (e.g. Electrical and Electronic Equipment Act).
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Unidad de control de Pilz
Pilz
Pilz PNOZ mc4p Manual de usuario
Pilz
Pilz PSSu E F 4DI Manual de usuario
Pilz
Pilz PNOZmulti PNOZ mmc3p Manual de usuario
Pilz
Pilz PNOZ m0p Manual de usuario
Pilz
Pilz PNOZ m EF 2MM Manual de usuario
Pilz
Pilz PSSu E S 2AI RTD Manual de usuario
Pilz
Pilz PMCtendo SZ Manual de usuario
Pilz
Pilz PNOZ mc7p Manual de usuario
Pilz
Pilz PSSuniversal PSSu H F PN Manual de usuario
Pilz
Pilz PIT js2 Manual de usuario
Pilz
Pilz PSSu E F 2DI 60-R Manual de usuario
Pilz
Pilz PIT es Set10u-5c PCB Manual de usuario
Pilz
Pilz PSSu E F PS2 Manual de usuario
Pilz
Pilz PZE 9P Manual de usuario
Pilz
Pilz PSEN ma1.4n-51 Manual de usuario
Pilz
Pilz PSS u2 ES 4AO U/I Manual de usuario
Pilz
Pilz PSS Series Manual de usuario
Pilz
Pilz PZE X4VP4 Manual de usuario
Pilz
Pilz PSSu E F 4DO 0.5 Manual de usuario
Pilz
Pilz PNOZ mi2p Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
