Molex 63823-6370 Manual de usuario

Hand Crimp Tool: for Quick Disconnect, High Reliability Terminal (HRT)

Doc o: ATS-6382363HM Release Date: 09-16-10 UNCONTROLLED COPY Page 1 of 6

Revision: B Revision Date: 10-14-10

TYPE 4A

INSULATION

CRIMP

▲

SEE NOTE

BRUSH

STRIP

LENGTH

TERMINAL

STRIP

CONDUCTOR

CRIMP HEIGHT

CUT-OFF

TAB

SEAM

BELL MOUTH

WIRE

Applicatio Tooli g

Specificatio Sheet

Modular Crimp Head

Order No. 63823-6370

Ha d Crimp Tool

Order No. 63823-6300

FEATURES

% A full cycle ratcheting hand tool ensures complete crimps

% Ergonomically designed soft handles

% Precisely designed crimping profiles with simple contact positioning

% Easy handling due to outstanding force ratio

% Modular Crimp Head is removable and can be use in the Air Powered Tool Order o.63816-0100,

accompanied by Air Powered Crimp Adapter (Order o. 63816-0700).

% Can also be used in the Battery Powered Tool Order o.63816-0200 (110 V) or 63816-0250 (220 V),

accompanied by Battery Powered Crimp Adapter (Order o. 63816-0600).

SCOPE

Products: Quick Disconnect, High Reliability Terminal (HRT), Female for 0.50-1.00mm² Wire.

Termi al Series No.

Termi al Order No. Wire Size I sulatio Diameter

Strip Le gth

Reel Form O ly mm² / AWG

mm I . mm I .

94512 94512-0100

94512-0101

0.50

2.60 Max

.102 Max

5.30-6.30

.209-.248

0.75

1.00

Customer to cut off terminal from reel: 0.20mm (.008”) maximum Cut-off Tab.

See crimp specification for the individual Insulation Diameter.

DEFINITION OF TERMS

Hand Crimp Tool: for Quick Disconnect, High Reliability Terminal (HRT)

Doc o: ATS-6382363HM Release Date: 09-16-10 UNCONTROLLED COPY Page 2 of 6

Revision: B Revision Date: 10-14-10

▲I sulatio Crimp Note:

Due to the terminal’s insulation grip design and/or

insulation diameter range, this tool uses “overlap” form

geometry in the insulation punch. This produces an

overlap insulation crimp (A620 – compliant). While the

insulation punch profile may appear “lopsided”, this is a

normal condition for this tool. See figure to the right.

(Some tools with multiple crimp pockets may not have

the “overlap” profile on all pockets).

CRIMP SPECIFICATIONS:

After crimping, the crimp profiles should measure the following.

Termi al Series No.

Wire Size

Co ductor Crimp Profile

Height Width

mm2 mm I . mm

I . 0.5

0.75

1.0

94512

0.50 1.40-1.50

.055-.059

2.40

.095

0.75 1.45-1.55

.057-.061

2.40

.095

1.00 1.55-1.65

.061-.065

2.40

.095

Termi al

Series No.

Wire Size

I sulatio Crimp Pull Force Mi imum

Height (Ref)

Width (Ref)

mm2 mm I . mm I . N Lb.

94512

0.50 2.90 .114 3.50 .138

78.45 17.64

0.75 3.10 .122 3.50 .138

117.68 26.46

1.00 3.10 .122 3.50 .138

156.91 35.27

■Tool Qualification otes:

1. Pull Force should be measured with no influence from the

insulation crimp.

2. The above specifications are guidelines to an optimum crimp.

OPERATION

Open the tool by squeezing the handles together, at the end of the

closing stroke, the ratchet mechanism will release the handles, and

the hand tool will spring open.

Crimpi g Termi als

1. Lift the wire stop blade up.

2. Insert the terminal fully into the correct profile until the terminal is fully seated and stops.

3. Bring down the wire stop blade.

4. Slide the pre-stripped wire into the wire stop blade. See Figure 1. Be sure to hold the wire in place until the

terminal is fully crimped. See Figure 2.

5. Close the tool until the ratchet releases, the tool handles will then spring open.

6. Lift the wire stop blade up if it is still in down position.

7. Carefully remove the crimped terminal.

TERMINAL

PRE-STRIPPED

WIRE

LOCATOR

Figure 1

WIRE STOP

BLADE

OVERLAP

INSULATION

CRIMP

OVERLAP FORM GEOMETRY

ANVIL

PUNCH

WIRE

Hand Crimp Tool: for Quick Disconnect, High Reliability Terminal (HRT)

Doc o: ATS-6382363HM Release Date: 09-16-10 UNCONTROLLED COPY Page 3 of 6

Revision: B Revision Date: 10-14-10

Note: To maintain good brush control and a consistent bell mouth the crimping instructions must be followed.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

Mai te a ce

It is recommended that each operator of the tool be made

aware of, and responsible for, the following maintenance

steps:

1. Remove dust, moisture, and other contaminants with a

clean brush, or soft, lint free cloth.

2. Do not use any abrasive materials that could damage

the tool.

3. Make certain all pins; pivot points and bearing surfaces

are protected with a thin coat of high quality machine

oil. Do not oil excessively. The tool was engineered for

durability but like any other equipment it needs cleaning

and lubrication for a maximum service life of trouble

free crimping. Light oil (such as 30 weight automotive oil) used at the oil points, every 5,000 crimps or 3

months, will significantly enhance the tool life.

4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto

certain terminations may affect the electrical characteristics of an application.

5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies,

and store the tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by lifting the ratchet release lever. See Figure 6.

Warra ty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital

components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30

days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will

not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping,

fixturing, or use of handle extensions voids this warranty.

CAUTION: Repetitive use of this tool should be avoided.

CAUTIONS:

1. Manually powered hand tools are intended for low volume or field repair. This tool is OT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

Figure 2

CONDUCTOR

PUNCH

WIRE

LOCATOR

TERMINAL

INSULATION

PUNCH

INSULATION

ANVIL

CONDUCTOR

ANVIL

WIRE STOP

BLADE

RETAINER

SPACER

Hand Crimp Tool: for Quick Disconnect, High Reliability Terminal (HRT)

Doc o: ATS-6382363HM Release Date: 09-16-10 UNCONTROLLED COPY Page 4 of 6

Revision: B Revision Date: 10-14-10

Notes:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height; however crimp force is adjustable (See instructions above).

Variations in tools, terminals, wire stranding, and insulation types may affect crimp height.

3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all

insulation sizes.

4. Molex does not repair hand tools (see warranty above). The replacement parts listed are the only parts

available for repair. If the handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no

influence from the insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips

on the terminal do not grip the wire insulation or the conductor. Refer to Molex Quality Crimping

Handbook 63800-0029 for additional information on crimping and crimp testing.

6. Molex does not certify crimp hand tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

Applicatio s for the Modular Crimp Head

WARNING: NEVER operate, service, install, or adjust this Modular Crimp Head without proper instruction

and without first reading and understanding the instructions in the proper Manual or Specification Sheet.

See Chart below for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. Disconnect the

power by unplugging or turn off the Actuator from its power source.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

Hand Crimp Tool: for Quick Disconnect, High Reliability Terminal (HRT)

Doc o: ATS-6382363HM Release Date: 09-16-10 UNCONTROLLED COPY Page 5 of 6

Revision: B Revision Date: 10-14-10

MODULAR

CRIMP

HEAD

BATTERY

POWER

CRIMP

ADAPTER

LOCKING

PINS

LOCKING PINS

BATTERY

POWERED

TOOL

AIR

POWER

TOOL

MODULAR

CRIMP HEAD

LOCKING

PINS

LOCKING

PINS

AIR

POWER

CRIMP

ADAPTER

The chart below shows all applications for this Modular Crimp Head.

Modular Crimp Head

Order No.

Tool

Order o.

Tool

Descriptio

Adapter

Order No.

Adapter

Descriptio

Figure

No.

63823-6370

63816-0000

Hand Crimp Frame (Short) /A /A 3

63816-0050

Hand Crimp Frame (Long) /A /A 3

63816-0200

Battery Power Tool (110 V)

63816-0600

Battery Power Crimp Adapter

63816-0250

Battery Power Tool (220 V)

63816-0600

Battery Power Crimp Adapter

63816-0100

Air Power Tool 63816-0700

Air Power Crimp Adapter 5

Applicatio s for the Modular Crimp Head

Ha d Crimp Tool Battery Powered Tool Air Powered Tool

Figure 3 Figure 4 Figure 5

MODULAR

CRIMP

HEAD

LOCKING

PINS

HAND CRIMP

FRAME LONG

OR SHORT

Hand Crimp Tool: for Quick Disconnect, High Reliability Terminal (HRT)

Doc o: ATS-6382363HM Release Date: 09-16-10 UNCONTROLLED COPY Page 6 of 6

Revision: B Revision Date: 10-14-10

RATCHET

RELEASE LEVER

HANDLE

SPRING

CRIMPING

SPRING (2)

Figure 6

M4 X 14mm

LONG BHCS

PARTS LIST

Ha d Crimp Tool 63823-6300

Item

Order Number

Descriptio Qua tity

1 63823-6370 Modular Crimp Head 1

2 63816-0050 Hand Crimp Frame (Long)

3 63823-6375 Locator 1

4 63816-0001 Locking Pin 2

5 63600-0525 Handle Spring 1

6 63600-0520 Crimping Spring 2

http://www.molex.com

X-ON Electronics

Largest Supplier of Electrical and Electronic Components

Click to view similar products for Crimpers category:

Click to view products by Molex manufacturer:

Other Similar products are found below :

576771-1 576788-2 010-0041 010-0055 010-0096 604228-1 M225202-37 CT150-2-D02 CT150-4-LY2 CT150-6-RH07 M322 63484-3701

63800-0140 63800-8355 63811-3275 63811-3376 63811-6375 63811-6475 63811-7875 63811-8175 63811-8875 63819-0475 63819-1875

63819-2875 63819-4375 63819-4475 63823-3475 63823-5175 63823-6375 63823-8375 63827-5375 64001-0975 64001-2175 64001-4175

662903-2 690142-4 690602-6 D38999/20WA98JB-LC 7-1633664-2 7-22278-0 7-22280-5 7-240641-3 762637-1 808714-1 8-1633117-3

853721-6 91362-1 995-0001-187 1-1633932-5 999-50-020083

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 207129 Series Manual de usuario

molex

molex 63823-4100 Manual de usuario

molex

molex 63811-7000 Manual de usuario

molex

molex 63827-8600 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex CR5974 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex PremiumGrade Series Manual de usuario

molex

molex 63819-0600 Manual de usuario

molex

molex 64001-7400 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63827-2100 Manual de usuario

molex

molex Perma-Seal 64005-4500 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 11-01-0185 Manual de usuario

molex

molex 63811-7070 Manual de usuario

molex

molex 44262-4306 Manual de usuario

molex

molex 63819-3500 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63823-5570 Manual de usuario

molex

molex 63811-7100 Manual de usuario

molex

molex 207129 Series Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario

molex 63823-6370 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas