Molex 63823-5570 Manual de usuario

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 1 of 9

Revision: A Revision Date: 03-09-11

INSULATION

CRIMP

▲SEE NOTE

BRUSH

STRIP

LENGTH

CONDUCTOR

CRIMP HEIGHT

CUT-OFF

TAB

SEAM

BELL MOUTH

WIRE

Application Tooling

Specification Sheet

Tool Kit

Order No. 63823-5570

Hand Crimp Tool

Order No. 63823-5500

FEATURES

A full cycle ratcheting hand tool ensures complete crimps

Ergonomically designed soft handles

Precisely designed crimping profiles with simple contact positioning

Easy handling due to outstanding force ratio

Tool kits are easily installed into the Hand Crimp Tool or the 63816-0300 Power Crimp Head which is installed

into the 63816-0200 (110 V) or the 63816-0250 (220 V) Battery Powered Tool.

Many different Tool kits can be used with a single Battery Powered Tool.

This tool is IPC/WHMA-A-620 Class 2 and RoHS compliant.

SCOPE

Products: .250 MP-Lock Terminals for 14-18 AWG Wire.

Terminal Series No.

Terminal Order No.

Wire Size

Insulation Diameter

Strip Length

Reel Form Only

AWG

mm²

In.

57989

57989-9810

2.00

2.2-3.4

.087-.134

5.00-5.50

.197-.217

1.30

0.80

Customer to cut off terminal from reel: 0.50mm (.020”) maximum Cut-off Tab.

DEFINITION OF TERMS

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the

scope.

TYPE 4C

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 2 of 9

Revision: A Revision Date: 03-09-11

▲Insulation Crimp Note:

Due to the terminal’s insulation grip design

and/or insulation diameter range, this tool

uses “overlap” form geometry in the

insulation punch. This produces an overlap

insulation crimp (A620 –compliant). While

the insulation punch profile may appear

“lopsided”, this is a normal condition for this

tool. See figure to the right. (Some tools with

multiple crimp pockets may not have the

“overlap” profile on all pockets).

CONDITIONS:

After crimping, the conductor profiles should

measure the following (see notes below).

Terminal

Series No.

Wire Size

Conductor Crimp

Insulation Crimp

Pull Force

Minimum

Profile

Height

Width (Ref)

Height

Width (Ref)

AWG

mm2

In.

Lbs

57989

2.00

1.77-1.87

.070-.074

2.75

.108

2.60

.102

4.50

.177

245.17

55.12

1.30

1.57-1.67

.062-.066

2.75

.108

2.70

.106

4.50

.177

205.94

46.30

0.80

1.45-1.55

.057-.061

2.75

.108

3.60

.142

4.50

.177

117.68

26.46

Tool Qualification Notes:

1. Pull Force should be measured with no influence from the insulation crimp.

2. The above specifications are guidelines to an optimum crimp.

Note:

A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands,

insulation diameters, and durometers, actual crimp height measurements may very slightly. An occasional,

destructive, pull force test should be preformed to check hand tool crimp. Pull Force value must exceed the

minimum pull force specifications listed.

CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage

can occur to the tool or die.

INSTALLATION

To install the Tool Kit into the Power Crimp Head follow the steps below:

Anvils and Punches Installation

1. Insert the Anvils into the bottom slots of the nest. Install the M4 x 10 long BHCS and tighten in place.

2. Insert the Punches into the top slots of the nest. Install the M4 x 18 long BHCS and tighten in place. See

Figure 1.

Locator Installation and Removal

Follow the steps below to install or replace the locator. See Figure 2.

OVERLAP

INSULATION

CRIMP

OVERLAP FORM GEOMETRY

ANVIL

PUNCH

WIRE

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 3 of 9

Revision: A Revision Date: 03-09-11

ANVILS

POWER

CRIMP

HEAD

Figure 1

PUNCHES

M4 X 10 LONG

BHCS

M4 X 18 LONG

BHCS

SWING

LOCATOR

OPEN

PRESS DOWN

ON THE BRASS

PIVOT SHAFT

LIFT UP ON

THE LOCATOR

Figure 2

To install the locator

1. Position the locator with the hole over the brass pivot shaft and snap it into place.

To remove the locator

1. Open the crimp hand tool.

2. Swing the existing locator open and away from the hand tool.

3. Firmly press down on the brass pivot shaft with your thumb, while pulling the locator up. Slip the locator off the

top of the brass pivot shaft.

OPERATION

Open the tool by squeezing the handles together, at the end of the closing stroke, the ratchet mechanism will

release the handles, and the hand tool will spring open.

Crimping Terminals

1. Select the desired terminal listed in the preceding

charts.

2. Turn the Locator Lock Latch down to unlock. See

Figure 3.

3. Swing the terminal locator away from the crimp tool

shown in Figure 4. Some terminals with large

insulation grips may interfere with the crimp tooling

when swinging the locator into position. The terminal

must then be loaded into the locator in the

closed/crimp position. See Figure 5.

4. Press down on the wire stop on the locator as shown

in Figure1. Insert the proper terminal into the proper

nest opening. Make sure when choosing the nest opening, it will correspond with the A, B or C profile on the

hand tool.

5. Return the locator to its original position.

6. Turn the Locator Lock Latch up to lock. Make sure that the terminal is visually centered over the punch.

Figure 3

LATCH LOCKED

LATCH UNLOCKED

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 4 of 9

Revision: A Revision Date: 03-09-11

SWING OPEN

TERMINAL

PUSH HERE TO

OPEN WIRE STOP

LOCATOR

TERMINAL

IN PLACE

Figure 4

LOCATOR LATCH

IN OPEN POSITION

Figure 6

WIRE IN TERMINAL

JAWS

PARTIALLY

CLOSED

WIRE AGAINST

WIRE STOP

HANDLE

OPEN

LOCATOR

CLOSED

Figure 5

TERMINAL

PUSH HERE TO

OPEN WIRE STOP

7. Insert the proper wire over the terminal.

8. Gently touch the wire stop with the end of the wire. See Figure 6 and 7.

9. Compress the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed.

Release handles to open the jaws.

10. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on

the wire. The terminal locator can be in either position.

11. Visually inspect the crimped terminal for proper crimp location.

Note: The tamper proof ratchet action will not release the tool until it has been fully closed.

For the Battery Power Tool:

1. Cycle the Battery Power Tool to crimp the terminal to the wire.

2. Remove the crimped terminal from the terminal locator by pressing down on the wire stop and gently pulling on

the wire. The terminal locator can be in either position.

3. Visually inspect the crimped terminal for proper crimp location.

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 5 of 9

Revision: A Revision Date: 03-09-11

Maintenance

It is recommended that each operator of the tool

be made aware of, and responsible for, the

following maintenance steps:

1. Remove dust, moisture and other

contaminants with a clean brush, or soft, lint-

free cloth.

2. Do not use any abrasive materials that could

damage the tool.

3. Make certain all pins; pivot points and bearing

surfaces in the tool head are protected with a

thin coat of high quality machine oil. Do not oil

excessively. This tool was engineered for durability, but like any fine piece of equipment, it needs cleaning

and lubrication for a maximum service life of trouble-free crimping. The use of light oil, such as 30 weight

automotive oil, every 5,000 crimps or monthly, will significantly enhance the tool life and ensure a stable

calibration. See Figure 8A or 8B for lubrication points.

4. Store the tool in a clean and dry area when not in use.

Miscrimps or Jams for Crimp Hand Tools Only

(See Figure 11)

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or

closed. The tool will open easily by rotating the

small slotted screw marked with an arrow. See

Figure 11.

Warranty

This tool kit is for electrical terminal crimping

purposes only. This tool kit is made of the best

quality materials. All vital components are long

life tested. All tools are warranted to be free of

manufacturing defects for a period of 30 days.

Should such a defect occur, we will repair or

exchange the tool kit free of charge. This repair

or exchange will not be applicable to altered,

misused, or damaged tools.

CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling.

CAUTIONS

1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for

production use. Repetitive use of this tool should be avoided.

2. Insulated rubber handles are not protection against electrical shock.

WIRE

Figure 7

WIRE

INSULATION

PUNCH

CONDUCTOR ANVIL

LOCATOR

INSULATION ANVIL

WIRES AGAINST

LOCATOR STOP

CONDUCTOR

PUNCH

TERMINAL

LUBRICATION

POINTS

(BOTH SIDES)

LIGHT OIL

(EVERY MONTH

5,000 CRIMPS)

Figure 8A

Figure 8B

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 6 of 9

Revision: A Revision Date: 03-09-11

3. Wear eye protection at all times.

4. Use only the Molex terminals specified for crimping with this tool.

CAUTION: Repetitive use of this tool should be avoided.

Certification

Molex does not certify or re-certify commercial grade hand tools but rather supplies the following guidelines for

customers to re-certify hand tools.

This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped

12.7mm (1/2”) long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than

25mm (1.00”) per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull

testing.

When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and

replaced.

This tool is very difficult to disassemble and reassemble. Customer repair is not recommended.

The chart below shows all applications for this Tool Kit.

Tool Kit

Order No.

Tool

Order no.

Tool

Description

Power Head

Order No.

Adapter

Description

Figure

No.

63923-5570

63810-1050

Hand Crimp Frame (Short)

N/A

63810-1000

Hand Crimp Frame (Long)

N/A

63816-0200

Battery Power Tool (110 V)

63816-0300

Power Crimp Head

63816-0250

Battery Power Tool (220 V)

63816-0300

Power Crimp Head

Applications for the Tool Kit

Hand Crimp Tool

Battery Powered Tool

Figure 9

Figure 10

POWER

CRIMP

HEAD

LOCKING PINS

BATTERY

POWERED

TOOL

TOOLING KIT

HAND CRIMP

FRAME LONG

AND SHORT

TOOLING KIT

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 7 of 9

Revision: A Revision Date: 03-09-11

WARNING: NEVER operate service, install tool kits, or adjust the Power Crimp Head without proper

instruction and without first reading and understanding the instructions in the proper Manual or

Specification Sheet. See Chart above for the correct Manual or Specification Sheet.

WARNING: NEVER install tooling or service this tool while it is into any power source. Make sure the

power is turned off.

CAUTION: Keep fingers away from the crimping area when operating this tool. It may cause severe injury.

CAUTION: Wear safety glasses when operating or serving this tool.

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 8 of 9

Revision: A Revision Date: 03-09-11

RATCHET

RELEASE SCREW

Figure 11

M4 X 8mm

LONG BHCS

M4 X 18mm

LONG BHCS

M4 X 10mm

LONG BHCS

WITH TOOL KIT

LOCATOR ONLY

HAND TOOL PARTS LIST

Item Number

Order Number

Description

Quantity

63810-1000

Hand Crimp Frame (Long)

63823-5570

Tool Kit with Locator

63811-4773

Locator Base

63823-5575

Locator (only)

REF

Tool Kit for 250 MP-Lock Terminal

Doc No: ATS-6382355HM Release Date: 03-09-11 UNCONTROLLED COPY Page 9 of 9

Revision: A Revision Date: 03-09-11

Figure 12

M4 by 8 Long

BHCS

M4 by 18 Long

BHCS

M4 by 10 Long

BHCS

POWER HEAD PARTS LIST

Item

Order No

Engineering No.

Description

Quantity

63816-0300

Power Crimp Head

63823-5570

Tool Kit

http://www.molex.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 64005-6200 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63827-0470 Manual de usuario

molex

molex AT FIFG Manual de usuario

molex

molex Perma-Seal 64005-4500 Manual de usuario

molex

molex 63823-7970 Manual de usuario

molex

molex 63811-5100 Manual de usuario

molex

molex 63811-1200 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63811-7200 Manual de usuario

molex

molex 63819-7670 Manual de usuario

molex

molex 63823-4100 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63825-5800 Guía del usuario

molex

molex AT 1992 Manual de usuario

molex

molex 63825-1670 Manual de usuario

molex

molex 63827-2970 Manual de usuario

molex

molex AT 2080 Guía del usuario

molex

molex 63828-0600 Manual de usuario

molex

molex 63825-2600 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63825-3000 Manual de usuario

molex

molex 64001-1000 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario

molex 63823-5570 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas