Molex CR60930A Manual de usuario

CR60930A Hand Crimp Tool “C-Grid” S.L. Terminals

Doc No. 11-01-0208 Release Date: 07-16-94 UNCONTROLLED COPY Page 1 of 5

Revision: E Revision Date: 11-01-04

INSULATION

CRIMP

BRUSH

STRIP

LENGTH

BELL MOUTH

CRIMP HEIGHT

BEND

DOWN

BEND UP

ROLLING

CONDUCTOR

CRIMP

TWISTING

HAND CRIMP TOOL

SPECIFICATION SHEET

Order No. 11-01-0208

(CR60930A)

FEATURES



Small handle spread which make this style tool ideally suited for end users



Ratchet with safety release that ensures consistent performance



A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position

SCOPE

Wire Size Insulation Diameter Strip LengthTerminal

Series No. AWG mm² mm In. mm In.

50088 22 - 24 0.35-0.20 1.09-1.65 .043-.065 2.54-3.17 .100-.125

50088 32 - 36 0.03-0.01 0.43-0.64 .017-.025 2.54-3.17 .100-.125

70021 22 - 24 0.35-0.20 1.09-1.65 .043-.065 2.54-3.17 .100-.125

70021 32 - 36 0.03-0.01 0.43-0.64 .017-.025 2.54-3.17 .100-.125

70058 20 - 24 0.50-0.20 1.09-1.70 .043-.067 2.54-3.17 .100-.125

70058 32 - 36 0.03-0.01 0.43-0.64 .017-.025 2.54-3.17 .100-.125

71851 22 - 24 0.35-0.20 1.09-1.65 .043-.065 2.54-3.17 .100-.125

71851 32 - 36 0.03-0.01 0.43-0.64 .017-.025 2.54-3.17 .100-.125

DEFINITION OF TERMS

The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope.

CR60930A Hand Crimp Tool “C-Grid”S.L. Terminals

Doc No. 11-01-0208 Release Date: 07-16-94 UNCONTROLLED COPY Page 2 of 5

Revision: E Revision Date: 11-01-04

CONDITIONS:

After crimping, the conductor profiles should measure the following (see notes on page 4).

Punch Width (Ref)

Wire Size Cond. Crimp

Height (Ref) Cond. Pull Force Min. Profile

Terminal

Series No. AWG mm2mm In. mm In. N Lb. A B

50088 22 0.35 0.71-0.81 .028-.032 1.33 .052 44.5 10.00 X

50088 24 0.20 0.71-0.81 .028-.032 1.33 .052 28.9 6.50 X

50088 32 0.03 0.58-0.69 .023-.027 1.08 .043 4.4 1.00 X

50088 34 0.02 0.58-0.69 .023-.027 1.08 .043 2.6 0.60 X

50088 36 0.01 0.58-0.69 .023-.027 1.08 .043 1.8 0.40 X

70021 22 0.35 0.71-0.81 .028-.032 1.33 .052 44.5 10.00 X

70021 24 0.20 0.71-0.81 .028-.032 1.33 .052 28.9 6.50 X

70021 32 0.03 0.58-0.69 .023-.027 1.08 .043 4.4 1.00 X

70021 34 0.02 0.58-0.69 .023-.027 1.08 .043 2.6 0.60 X

70021 36 0.01 0.58-0.69 .023-.027 1.08 .043 1.8 0.40 X

70058 20 0.50 0.76-0.86 .030-.034 1.33 .052 57.8 13.00 X

70058 22 0.35 0.71-0.81 .028-.032 1.33 .052 44.5 10.00 X

70058 24 0.20 0.71-0.81 .028-.032 1.33 .052 28.9 6.50 X

70058 32 0.03 0.58-0.69 .023-.027 1.08 .043 4.4 1.00 X

70058 34 0.02 0.58-0.69 .023-.027 1.08 .043 2.6 0.60 X

70058 36 0.01 0.58-0.69 .023-.027 1.08 .043 1.8 0.40 X

71851 22 0.35 0.71-0.81 .028-.032 1.33 .052 44.5 10.00 X

71851 24 0.20 0.71-0.81 .028-.032 1.33 .052 28.9 6.50 X

71851 32 0.03 0.58-0.69 .023-.027 1.08 .043 4.4 1.00 X

71851 34 0.02 0.58-0.69 .023-.027 1.08 .043 2.6 0.60 X

71851 36 0.01 0.58-0.69 .023-.027 1.08 .043 1.8 0.40 X

CR60930A Hand Crimp Tool “C-Grid”S.L. Terminals

Doc No. 11-01-0208 Release Date: 07-16-94 UNCONTROLLED COPY Page 3 of 5

Revision: E Revision Date: 11-01-04

OPERATION

Open the tool by squeezing the handles together, at the end of the closing stroke, the

ratchet mechanism will release the handles, and the hand tool will spring open.

Crimping Terminals

1. Lift the locator blade and place the terminal into the correct die profile (A or B),

release the locator blade. Not all tools are equipped with a locator or locator

blade.

2. Partially close the tool until the terminal is held in

place, (See Figure 2).

3. Place a wire into the terminal and up against the locator

blade, (See Figure 3). On tools without locators line the

wire up with the conductor and insulation grips visually.

4. Close the tool until the ratchet releases, (See

Figure 4).

5. Lift the locator blade or wire stop up.

6. Carefully remove the crimped terminal.

Maintenance

It is recommended that each operator of the tool be made aware of, and responsible

for, the following maintenance steps:

1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint

free cloth.

2. Do not use any abrasive materials that could damage the tool.

3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil

excessively.

4. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the

tool in a clean, dry area.

Miscrimps or Jams

Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will

open easily by lifting the ratchet release lever (See Figure 4).

Figure 2

Figure 3

TERMINAL

PRE-STRIPPED WIRE

Figure 1

CR60930A Hand Crimp Tool “C-Grid”S.L. Terminals

Doc No. 11-01-0208 Release Date: 07-16-94 UNCONTROLLED COPY Page 4 of 5

Revision: E Revision Date: 11-01-04

CAUTION: Molex crimp specifications are valid only when used with Molex terminals, applicators and tooling.

How To Adjust Tool Crimp Force (See Figure 4)

It may be necessary over the life of the tool to adjust tool-crimping force. Listed below are the steps required to adjust the crimping

force of the hand tool to obtain proper crimp conditions:

1. Remove the screw and washer. Located over the adjustment ring.

2. Lift the adjusting ring slightly, off of the locating pin.

3. Turn the adjusting ring in the desired direction (L= less force, T= more force) to increase or decrease crimp pressure.

4. Press the adjusting wheel flat against the tool and engage the locking pin.

5. Replace the washer and screw.

6. Check the crimp specifications after tool crimp force is adjusted.

Warranty

This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long

life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we

would exchange the tool free of charge. This will not be applicable to altered, misused, or damaged tools. This tool is designed for

hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty.

Hand held crimping tools are intended for low volume, prototyping, or repair requirements only.

Notes:

1. This tool should only be used for the terminals and wire gauges specified on this sheet.

2. This tool is not adjustable for crimp height, however crimp force is adjustable (See instructions above). Variations in tools,

terminals, wire stranding and insulation types may affect crimp height.

3. This tool is intended for standard conductor sizes. It may not give a good insulation crimp support for all insulation sizes.

4. Molex does not repair hand tools (see warranty above) The replacement parts listed are the only parts available for repair. If the

handles or crimp tooling is damaged or worn, a new tool must be purchased.

5. Pull force should be used as the final criteria for an acceptable crimp. Pull force is measured with no influence from the

insulation crimp. The insulation should be stripped long (1/2 in.) so the insulation grips on the terminal do not grip the wire

insulation or the conductor. Refer to Molex Quality Crimping Handbook 63800-0029 for additional information on crimping

and crimp testing.

6. Molex does not certify crimp hand tools.

Caution: Repetitive use of this tool should be avoided.

CR60930A Hand Crimp Tool “C-Grid”S.L. Terminals

Doc No. 11-01-0208 Release Date: 07-16-94 UNCONTROLLED COPY Page 5 of 5

Revision: E Revision Date: 11-01-04

M4 NUT

RATCHET

RELEASE LEVER

ADJUSTMENT

RING

LOCATOR

BLADE

Figure 4

M4 X 18LG BHCS

PARTS LIST

Item Number Order Number Description Quantity

1 11-11-0383 Locator Assembly** 1

2 11-11-0324 Spring (Main) 1

3 11-11-0320 Spring (Ratchet) 1

** Not all tools are equipped with a locator or locator blade.

Molex Application Tooling Group

1150 E. Diehl Road

Naperville, IL, 60563

Tel: 630-969-4550

Fax: 630-505-0049

Visit our Web site at http://www.molex.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Herramientas de crimpado de molex

molex

molex 207129 Series Manual de usuario

molex

molex 63903-8900 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex CR60639B Manual de usuario

molex

molex 63819-4400 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63827-2970 Manual de usuario

molex

molex 35745 Series Manual de usuario

molex

molex 98897 Manual de usuario

molex

molex 63811-6170 Manual de usuario

molex

molex TPX50-50 Guía del usuario

molex

molex 207129 Series Manual de usuario

molex

molex 63811-7200 Manual de usuario

molex

molex AT-1300 Manual de usuario

molex

molex CR5974 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex 43178 Series Manual de usuario

molex

molex 63819-4100 Manual de usuario

molex

molex 207129 Series Manual de usuario

molex

molex CR5907 Manual de usuario

molex

molex 63825-3000 Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas

Panduit

Panduit CT-1000 Guía del administrador

JST

JST CS 10 Manual de usuario

Danfoss

Danfoss ET4200 Manual de usuario

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manual de usuario

TE Connectivity

TE Connectivity 2063528-1 Manual de usuario

Tyco Electronics

Tyco Electronics 69156-1 Manual de usuario

CRH

CRH CRL CBLHCT1 Manual de usuario

Emerson

Emerson Klauke ES 105CFM Manual de usuario

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manual de instrucciones

Danfoss

Danfoss ET4350 Manual de usuario

Milwaukee

Milwaukee M18 Manual de usuario

HOGERT

HOGERT HT1P169 Manual de usuario

Textron

Textron ESG105L Manual de usuario

Tyco Electronics

Tyco Electronics 90035-3 Manual de usuario

Emerson

Emerson Klauke ES 20RMCCFB Manual de usuario

Continental Refrigerator

Continental Refrigerator PC150HD Manual de usuario

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manual de usuario

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manual de usuario

molex CR60930A Manual de usuario

Manuales populares de Herramientas de crimpado de otras marcas