MicroNet SP212E Manual de usuario
Quick Installation Guide
2/4-Port KVM Switch
Model No.: SP212E/ SP212EL/ SP214E/ SP214EL
World Wide Web: www.micronet.com.tw ; www.micronet.info
1
Introduction
The Micronet SP212E/ SP212EL/ SP214E/ SP214EL 2/4-Port KVM
switch is a compact device for managing multiple PCs via a single
set of local equipment (keyboard, mouse, and monitor). Its compact
in nature helps user to placed on desktop or be hidden from view. In
addition, SP212E and SP214E supports both audio and microphone
interface allowing multiple PCs to share the single set of sound
device. All models provide push button and hotkey for easy
operation at a touch of a fingertip.
Package Contents
Please verify the following items are in the package:
SP212E/SP214E SP212EL/SP214EL
y2/4-Port KVM Switch
yQuick Installation Guide
y2/4 x KVM Cable
y2/4 x Audio Cable
y2/4-Port KVM Switch
yQuick Installation Guide
y2/4 x KVM Cable
Note: Contact your dealer immediately if any of the above items are
missing, damaged, or if the unit does not work.
2
Key Features
ySupports high VGA resolutions up to 2048 x 1536
yControl 2/4 computers with one keyboard, mouse and monitor
ySupport audio and microphone switching function with one
speaker and microphone (SP212E/SP214E only)
ySupport scrolling mouse & multi-button mouse (Microsoft,
Logitech, etc.)
yEasy installation with Plug & Play, no external software or other
supporting interface card required
ySwitch computers easily with convenient hotkeys and push
button
yCompatible with Windows and Linux operating systems
ySupports Mac and Sun Micro System (NOTE: Only support
standard PS/2 Keyboard & Mouse)
ySupports Auto-Scan function to alternate video between both
computers in preset intervals 5~100 sec.
3
Hardware Installation
Please follow steps below to setup the hardware:
Step 1: Make sure that all computers are connected to the KVM
Switch with the provided KVM cable and their peripherals are in
power-off state.
Step 2: Connect the shared PS/2 keyboard, mouse and VGA
monitor to the KVM switch.
Step 3: Connect the shared speaker set and microphone to the
KVM switch (SP212E/ SP214E only).
Step 4: Connect PC’s audio and microphone interface to KVM
switch using the Audio cable.
Step 5: Power on all PCs, KVM will now automatically initiate and
recognize mouse and keyboard.
Push Button Control
The Push Button is located on the top of the device for users to
switch between PCs. On default, PC port and Audio/Mic port are
bound together. Meaning when switching between PC ports,
Audio/Mic will also be changed. For more information on binding and
unbinding of Audio/Mic, please refer to Hotkey Control.
4
Redefining Hotkey Control
Redefining Hotkey can be achieved through both hotkey and push
button. (Allowed Hotkey: Scroll Lock, Caps Lock, Esc, F12 or Num
Lock)
Step 1: Pressing current hotkey twice then ‘H’, the system will signal
with two beeps alarm, then enter the new hotkey. For example,
default hotkey is Scroll Lock then command sequence is (y is the
new user-defined hotkey):
Scroll Lock + Scroll Lock + H + (y)
Step 2: Alternatively, users can change the hotkey by pressing and
holding the last push button of the device (Button 2 for 2-Port KVM
Switch and Button 4 for 4-Port KVM). By holding the button for more
than 3 seconds, the device will enter hotkey configuration mode then
press the preferred hotkey to complete the setting.
Note: Each keystroke in the hotkey sequence should be within 2
seconds for valid command execution.
Hotkey Command
Troubleshooting & Tips
1. Hotkey Convention: The hotkey notation (Scroll Lock + Scroll
Lock + key) requires users to press the command in
consecutive order, not simultaneously.
2. Mouse Troubleshoot: Execute the following hotkey
commands when mouse fail to response or malfunction.
¾PnP O/S (Windows 98/98SE/2000/XP):
ScrLk + ScrLk + End
¾Non-PnP O/S (Linux/NT 4.0):
2-key mouse: ScrLk + ScrLk + M + 1
3-key wheel mouse: ScrLk + ScrLk + M + 2
5-key wheel mouse: ScrLk + ScrLk + M + 3
3. On default, Audio/Mic and PC selection are bind together
(SP212EL/ SP214EL Only). To unbind, execute hotkey
command: ScrLk + ScrLk + W. To applying binding, run the
command: ScrLk + ScrLk + Q.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Cambiar de MicroNet
MicroNet
MicroNet SP6008P Manual de usuario
MicroNet
MicroNet SP6824P Manual de usuario
MicroNet
MicroNet SP6528 Manual de usuario
MicroNet
MicroNet SP6008P Manual de usuario
MicroNet
MicroNet SP6005P4 Manual de usuario
MicroNet
MicroNet SP616DB Manual de usuario
MicroNet
MicroNet SP508C Manual de usuario
MicroNet
MicroNet EtherFast SP624EA Manual de usuario
MicroNet
MicroNet SP659B Manual de usuario
MicroNet
MicroNet SP212D Manual de usuario
MicroNet
MicroNet SP1678A Manual de usuario
MicroNet
MicroNet SP212E Manual de usuario
MicroNet
MicroNet SP6008P Manual de usuario
MicroNet
MicroNet SP3524A Manual de usuario
MicroNet
MicroNet SP6524PWS Manual de usuario
MicroNet
MicroNet SP616R Manual de usuario
MicroNet
MicroNet SP1659P Manual de usuario
MicroNet
MicroNet SP6008PWS Manual de usuario
MicroNet
MicroNet SP1684B Manual de usuario
MicroNet
MicroNet SP6008P Manual de usuario
