Cabletron Systems GIGAswitch GSR-16 Manual de usuario

DIGITAL GIGAswitch/Router

Getting Started Guide

December 1999

This manual describes how to install andsetup the DIGITAL

GIGAswitch/Router (GSR).

Revision/Update Information: This is a revised document.

Part Number:9032681-04

Changes

Cabletron Systems reserves the right to make changes in specifications and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

Disclaimer

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT,

SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED

TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION

CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR

SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

Printed in the United States of America

Trademarks

Cabletron Systems and SPECTRUM are registered trademarks and Cabletron, clearVISN, and

GIGAswitch are trademarks of Cabletron Systems, Inc.

DIGITAL, DEC, and the DIGITAL logo are registered trademarks of DIGITAL Equipment Corporation.

HP is a registered trademark and OpenView is a trademark of Hewlett-Packard Company.

Pentium is a registered trademark of Intel Corporation.

Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation.

Netscape Navigator is a registered trademark of Netscape Communications Corporation.

Java and Solaris are trademarks of Sun Microsytems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies.

FCC Notice — Class A Computing Device

iii

FCC Notice — Class A Computing Device

This equipment generates, uses, and may emit radio frequency energy. The equipment has been type

tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC

rules, which are designed to provide reasonable protection against such radio frequency interference.

Operation of this equipment in a residential area may cause interference in which case the user at his

own expense will be required to take whatever measures may be required to correct the interference.

Any modifications to this device - unless expressly approved by the manufacturer - can void the user's

authority to operate this equipment under part 15 of the FCC rules.

Industry Canada Notice

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

NOTICE: The Industry Canada label identifies certified equipment. This certification means that the

equipment meets telecommunications network protective, operational and safety requirements as

prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The

department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the

facilities of the local telecommunications company. The equipment must also be installed using an

acceptable method of connection. The customer should be aware that compliance with the above

conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier.

Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power

utility, telephone lines and internal metallic water pipe system, if present, are connected together. This

precaution may be particularly important in rural areas. Caution: Users should not attempt to make

such connections themselves, but should contact the appropriate electric inspection authority, or

electrician, as appropriate.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an

indication of the maximum number of terminals allowed to be connected to a telephone interface. The

termination on an interface may consist of any combination of devices subject only to the requirement

that the sum of the ringer equivalence Numbers of all the devices does not exceed 5.

VCCI Notice — Class A Computing Device

This equipment is a Class A product (information equipment to be used in commercial and/or

industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference

by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference

in commercial and/or industrial areas. Consequently, when used in a residential area or in an adjacent

area thereto, radio interference may be caused to radios and TV receivers. Read the instructions for

correct handling.

Taiwanese Notice — Class A Computing Device

CE Notice — Class A Computing Device

Warning!

This is a Class A product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

Achtung!

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes

Rundfunkstörungen auftreten, in welchen Fällen der Benutzer für entsprechende Gegenmaßnahmen

verantwortlich ist.

Avertissement!

Cet appareil est un appareil de Classe A. Dans un environnement résidentiel cet appareil peut provoquer

des brouillages radioélectriques. Dans ce cas, il peut être demandé à l'utilisateur de prendre les mesures

appropriées.

Cabletron Systems, Inc. Program License Agreement

IMPORTANT: Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)

that sets forth your rights and obligations with respect to the Cabletron software program (the

“Program”) contained in this package. The Program may be contained in firmware, chips or other

media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND

BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE

LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE

TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT TO THE PLACE

OF PURCHASE FOR A FULL REFUND.

Cabletron Software Program License

1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package

subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws

and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and

venue of the New Hampshire courts.

Exclusion of Warranty and Disclaimer of Liability

1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing,

Cabletron makes no warranty, expressed or implied, concerning the Program (including its

documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY

CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT

LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING

WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR

ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT

LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION,

LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR

RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE

THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL

DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME

INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

SAFETY INFORMATION

United States Government Restricted Rights

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer

software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the

Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects is

proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the

DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its

successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in

subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at 252.227-7013.

Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

SAFETY INFORMATION

CLASS 1 LASER TRANSCEIVERS

The DGSRF-AA 100Base-FX Module, DGSRS-AA 1000Base-LX Module, and DGSRL-AA 1000Base-

LX Module use Class 1 Laser transceivers. Read the following safety information before installing

or operating these modules.

The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This

control loop eliminates the need for maintenance checks or adjustments. The output is factory set, and

does not allow any user adjustment. Class 1 Laser transceivers comply with the following safety

standards:

• 21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).

• IEC Publication 825 (International Electrotechnical Commission).

• CENELEC EN 60825 (European Committee for Electrotechnical Standardization).

When operating within their performance limitations, laser transceiver output meets the Class 1

accessible emission limit of all three standards. Class 1 levels of laser radiation are not considered

hazardous.

Laser Radiation and Connectors

When the connector is in place, all laser radiation remains within the fiber. The maximum amount of

radiant power exiting the fiber (under normal conditions) is -12.6 dBm or 55 x 10-6 watts.

Removing the optical connector from the transceiver allows laser radiation to emit directly from the

optical port. The maximum radiance from the optical port (under worst case conditions) is

0.8 W cm-2 or 8 x 103W m2sr-1.

Do not use optical instruments to view the laser output. The use of optical instruments to view

laser output increases eye hazard. When viewing the output optical port, power must be removed

from the network adapter.

DECLARATION OF CONFORMITY

vii

DECLARATION OF CONFORMITY

Application of Council Directive(s): 89/336/EEC

73/23/EEC

Manufacturer’s Name: Cabletron Systems, Inc.

Manufacturer’s Address: 35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name: Mr. J. Solari

European Representative Address: Cabletron Systems Limited

Nexus House, Newbury

Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment: Networking Equipment, for

use in a Commercial or Light

Industrial Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with

this notice conforms to the above directives.

Manufacturer Legal Representative in Europe

Mr. Ronald Fotino Mr. J. Solari

Full Name Full Name

Principal Compliance Engineer Managing Director - E.M.E.A.

Title Title

Rochester, NH, USA Newbury, Berkshire, England

Location Location

DIGITAL GIGAswitch/Router Getting Started Guide ix

Contents

About This Guide..................................................................................... xi

Who Should Read This Guide?............................................................................................ xi

How to Use This Guide......................................................................................................... xi

Related Documentation........................................................................................................ xii

Correspondence..................................................................................................................... xii

Getting Help..........................................................................................................................xiii

Safety....................................................................................................... xv

Overview................................................................................................................................ xv

Safety Requirements ............................................................................................................ xvi

Chapter 1: Features Overview ................................................................. 1

Specifications ............................................................................................................................2

Features......................................................................................................................................5

Hardware Overview..............................................................................................................10

Chapter 2: Hardware Installation .......................................................... 29

Safety Considerations............................................................................................................29

Hardware Specifications .......................................................................................................30

Installing the Hardware ........................................................................................................31

Chapter 3: Software Installation and Setup ......................................... 51

Installing a PCMCIA Flash Card .........................................................................................52

Powering On and Booting the Software .............................................................................53

Starting the Command Line Interface.................................................................................53

Setting the Basic System Information..................................................................................56

Setting Up SNMP Community Strings ...............................................................................59

Setting Up Passwords............................................................................................................61

Setting the DNS Domain Name and Address....................................................................62

Setting the SYSLOG Parameters ..........................................................................................64

Loading the System Image Software...................................................................................66

Loading the Boot PROM Software ......................................................................................67

Activating the Configuration Changes and Saving the Configuration File ..................68

Contents

x DIGITAL GIGAswitch/Router Getting Started Guide

Chapter 4: Installing and Starting DIGITAL clearVISN CoreWatch....... 71

What Is DIGITAL clearVISN CoreWatch?......................................................................... 72

System Requirements ........................................................................................................... 72

Installing DIGITAL clearVISN CoreWatch ....................................................................... 73

Starting DIGITAL clearVISN CoreWatch.......................................................................... 75

Appendix A: Troubleshooting................................................................ 79

Index ........................................................................................................ 83

Otros manuales para GIGAswitch GSR-16

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Cabletron Systems

Cabletron Systems

Cabletron Systems 6H122-16 Manual de usuario

Cabletron Systems

Cabletron Systems ESX-1320 Manual de usuario

Cabletron Systems

Cabletron Systems Ethernet Hubs Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch 9A100 Instrucciones de montaje

Cabletron Systems

Cabletron Systems SmartSwitch 6500 Manual de usuario

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-8TXUF2 Manual de usuario

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH Manual de usuario

Cabletron Systems

Cabletron Systems HubSTACK SEHI-34 Manual de usuario

Cabletron Systems

Cabletron Systems MRX Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch 8000 Manual de usuario

Cabletron Systems

Cabletron Systems MRXI 10BASE-T Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Manual de usuario

Cabletron Systems

Cabletron Systems 9E423-36 Manual de usuario

Cabletron Systems

Cabletron Systems SEH-22 Manual de usuario

Cabletron Systems

Cabletron Systems SmartSTACK ELS10-27TX Manual del propietario

Cabletron Systems

Cabletron Systems SmartSwitch 6500 Instrucciones de montaje

Cabletron Systems

Cabletron Systems 9A656-04 Instrucciones de instalación y funcionamiento

Cabletron Systems

Cabletron Systems MMAC-Plus 9F310-02 Documento técnico

Cabletron Systems

Cabletron Systems SmartCell ZX-250 Manual de usuario

Cabletron Systems

Cabletron Systems FN10 Manual de usuario

Cabletron Systems

Cabletron Systems STHI Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9H531-24 Manual de usuario

Cabletron Systems

Cabletron Systems SmartSwitch 2500 Manual de usuario

Cabletron Systems

Cabletron Systems Fast Network 10 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario