Kramer TP-580TD Manual de usuario

P/N: 2900-300868 Rev 1 www.KramerAV.com

USER MANUAL

MODEL:

TP‑580TD, TP‑580RD

DVI Line Transmitter / Receiver

Kramer Electronics Ltd.

‑

580TD, TP

‑

580RD – Contents

Contents

Introduction 1

Getting Started 1

Overview 2

Typical Applications 3

Defining the TP‑580TD DVI Line Transmitter 4

Defining the TP‑580RD DVI Line Receiver 5

Connecting the TP‑580TD, TP‑580RD DVI Line Transmitter / Receiver 6

Wiring the HDBT RJ 45 Connectors 7

Controlling A/V Equipment via an IR Remote Control 7

Connecting to TP‑580TD, TP‑580RD via RS-232 8

Technical Specifications 9

Default Communication Parameters 9

Kramer Electronics Ltd.

TP‑580TD, TP‑580RD – Introduction 1

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world

of unique, creative, and affordable solutions to the vast range of problems that confront the

video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we

have redesigned and upgraded most of our line, making the best even better!

Getting Started

We recommend that you:

•Unpack the equipment carefully and save the original box and packaging materials for

possible future shipment.

•Review the contents of this user manual.

Go to

www.kramerav.com/downloads/TP-580TD to check for up-to-date user manuals,

application programs, and to check if firmware upgrades are available (where appropriate).

Achieving the Best Performance

•Use only good quality connection cables (we recommend Kramer high-performance,

high-resolution cables) to avoid interference, deterioration in signal quality due to poor

matching, and elevated noise levels (often associated with low quality cables).

•Do not secure the cables in tight bundles or roll the slack into tight coils.

•Avoid interference from neighboring electrical appliances that may adversely influence

signal quality.

•Position your Kramer TP‑580TD and TP‑580RD away from moisture, excessive sunlight

and dust.

This equipment is to be used only inside a building. It may only be connected to other

equipment that is installed inside a building.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit

Warning:

Use only the Kramer Electronics power supply that is provided with the unit

Warning:

Disconnect the power and unplug the unit from the wall before installing

Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce

the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected

and recycled. To comply with the WEEE Directive, Kramer Electronics has made

arrangements with the European Advanced Recycling Network (EARN) and will cover any

costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on

Kramer Electronics Ltd.

TP‑580TD, TP‑580RD – Introduction 2

arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular

country go to our recycling pages at www.kramerav.com/support/recycling.

Overview

Congratulations on purchasing your Kramer TP‑580TD DVI Line Transmitter and/or TP‑

580RD DVI Line Receiver. TP‑580TD and TP‑580RD are a high-performance, long-reach

DVI Line Transmitter / Receiver for 4K@60Hz (4:2:0) DVI/HDMI, RS-232 and IR signals

over twisted pair. TP‑580TD and TP‑580RD extend video signals to up to 40m (130ft) over

CAT copper cables at up to 4K@60Hz (4:2:0) 24bpp video resolution and provides even

further reach for lower HD video resolutions. TP‑580TD/TP‑580RD can be connected to any

market-available HDBaseT-compliant extension product.

•High Performance Standard Extender −Professional HDBaseT extender for providing

long-reach signals over twisted-pair copper infrastructures. For optimum extension reach

and performance, use recommended Kramer cables.

•Secured Operation — Highly-secured operation is ensured by lockable wiring

connectivity with protection against unintentional cable disconnection.

•HDMI Signal Extension — HDMI 2.0 and HDCP 2.2 compliant, via single-link DVI-I

connection. Supports deep color, x.v.Color™, lip sync, HDMI uncompressed audio

channels, Dolby TrueHD, DTS-HD, 2K, 4K, and 3D. EDID signals are passed through

from the source to the display.

•I-EDIDPro™ Kramer Intelligent EDID Processing™ — Intelligent EDID pass-through that

ensures Plug and Play operation for HDMI source and display systems.

•Multi-channel Audio Extension — Up to 32 channels of digital stereo uncompressed

signals for supporting studio-grade surround sound.

•Bidirectional RS-232 Extension — Serial interface data flows in both directions, allowing

data transmission and device control.

•Bidirectional Infrared Extension — IR interface data flows in both directions, allowing

remote control of peripheral devices located at either end of the extended line.

•Cost-effective Maintenance — Status LED indicators for DVI and HDBT ports facilitate

easy local maintenance and troubleshooting.

•Easy Installation — Compact DigiTOOLS®fan-less enclosure for dropped-ceiling

mounting, or side-by-side mounting of 3 units in a 1U rack space. For more information

on side-by-side mounting, go to www.kramerav.com/downloads/TP-580TD.

Kramer Electronics Ltd.

TP‑580TD, TP‑580RD – Introduction 3

Typical Applications

TP‑580TD and TP‑580RD are ideal for the following typical applications:

•Medical operation rooms and other critical AV extension applications.

•Highly reliable, long-distance extension of high-quality professional AV signals via

lockable cable connections.

•Governmental high-reliability AV extension applications.

•Rental and Staging events.

Kramer Electronics Ltd.

TP‑580TD, TP‑580RD – Defining the TP‑580TD DVI Line Transmitter 4

Defining the TP‑580TD DVI Line

Transmitter

Figure 1: TP‑580TD DVI Line Transmitter

Feature

Function

IN LED

Lights green when an active DVI source device input signal is detected.

OUT LED

Lights green when an active, far-end sink (acceptor) DVI output signal is detected

via the HDBaseT link (a DVI signal is detected from a sink device connected to

the HDBaseT receiver that is connected to this output).

LINK LED

Lights green when an HDBT link is established with the HDBaseT receiver.

ON LED

Lights green when the device receives power.

HDBT OUT RJ-45

Connector

Connect to the HDBT IN connector on a receiver (for example, TP

‑

580RD).

DVI IN Connector Connect to a DVI source.

PROG/NORMAL

Switch

Slide to PROG to upgrade to the latest Kramer firmware via RS-232 or slide to

NORMAL for normal operation.

RS-232 3-pin

Terminal Block

Connector

Connect to a laptop to control TP

‑

580TD or perform firmware upgrade.

Connect to a controller device (for example, SL-240C) to serially control a remote

device (for example, the DVI OUT acceptor) that is connected to TP

‑

580RD.

IR 3.5mm Mini

Jack Connector

Connect to an external infrared emitter / sensor.

12V DC Power

Connector

12V DC connector for powering the unit.

Kramer Electronics Ltd.

TP‑580TD, TP‑580RD – Defining the TP‑580RD DVI Line Receiver 5

Defining the TP‑580RD DVI Line

Receiver

Figure 2: TP‑580RD DVI Line Receiver

# Feature Function

IN LED Lights green when an active far-end source DVI input signal is detected via the

HDBaseT link (a DVI signal is detected from a source device connected to the

HDBaseT transmitter that is connected to this input).

OUT LED Lights green when an DVI output signal is detected.

LINK LED Lights green when an HDBT link is established with the HDBaseT transmitter.

ON LED Lights green when the device receives power.

HDBT IN RJ-45

Connector

Connect to the RJ-45 HDBT OUT connector on a transmitter (for example, TP

‑

580TD).

DVI OUT

Connector

Connect to a DVI acceptor.

PROG/NORMAL

Switch

Slide to PROG to upgrade to the latest Kramer firmware via RS-232 or slide to

NORMAL for normal operation.

RS-232 3-pin

Terminal Block

Connector

Connect to a laptop to control TP

‑

580RD or perform firmware upgrade.

Connect to a controlled device (for example, the DVI OUT acceptor) to control it

from a remote serial controller (for example, SL-240C) that is connected to

TP‑580TD

IR 3.5mm Mini

Jack Connector

Connect to an external infrared emitter / sensor.

12V DC Power

Connector

12V DC connector for powering the unit.

Kramer Electronics Ltd.

TP‑580TD, TP‑580RD – Connecting the TP‑580TD, TP‑580RD DVI Line Transmitter / Receiver 6

Connecting the TP‑580TD, TP‑

580RD DVI Line Transmitter /

Receiver

Always switch off the power to each device before connecting it to your transmitter and

receiver. After connecting your transmitter and receiver, connect their power and then

switch on the power to each device.

You can use the TP‑580TD DVI Line Transmitter and the TP‑580RD DVI Line Receiver to

configure an DVI transmitter/receiver system, as shown in the example in Figure 3.

Figure 3: Connecting the TP‑580TD, TP‑580RD DVI Line Transmitter / Receiver

To connect the TP‑580TD, TP‑580RD DVI Line Transmitter / Receiver:

1. Connect a DVI source (for example, a Blu-ray player) to the DVI IN connector.

2. Connect the DVI OUT connector to the DVI acceptor, (for example, a display).

3. On the TP‑580TD, connect the RS-232 3-pin terminal block connector to the RS-232

port of a controller device (for example, the Kramer SL-240C).

4. On the TP‑580RD, connect the RS-232 3-pin terminal block to the device to be

controlled, (for example, a display that is controlled by SL-240C which is connected to

TP‑580TD).

5. On the TP‑580TD, connect the IR 3.5mm mini jack to an IR emitter that is connected to

the IR-controlled device (for example, a Blu-ray player).

6. On the TP‑580RD, connect the 3.5mm mini jack to an IR sensor.

7. Connect the supplied power adapters to the power sockets of the TP‑580TD and

TP‑580RD, and plug the adapters into the mains electricity (not shown in Figure 3).

Kramer Electronics Ltd.

TP‑580TD, TP‑580RD – Connecting the TP‑580TD, TP‑580RD DVI Line Transmitter / Receiver 7

Wiring the HDBT RJ 45 Connectors

This section defines the HDBT line pinout, using a straight pin-to-pin cable with RJ 45

connectors.

Note, For HDBT cables, it is recommended that the cable g

round shielding be

connected/soldered

to the connector shield.

EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

Controlling A/V Equipment via an IR Remote Control

You can use an IR remote-control transmitter (that is used for controlling a peripheral device,

for example, a Blu-ray disk player) to send commands from the receiver system to the

transmitter or to send commands from the transmitter system to the receiver. To use an IR

remote-control transmitter, connect the Kramer IR sensor cable at one end, and the Kramer

IR emitter cable at the other end.

The example in Figure 3illustrates how to control a Blu-ray player that is connected to the

TP‑580TD using a remote control located on the TP‑580RD side. An IR sensor is connected

to the TP‑580RD and an IR emitter is connected between the TP‑580TD and the Blu-ray

player. The Blu-ray remote control sends a command while pointed at the external IR sensor.

The IR signal is passed over the HDBT link and the IR emitter connected to the Blu-ray player

responds to the command sent.

Kramer Electronics Ltd.

TP‑580TD, TP‑580RD – Connecting the TP‑580TD, TP‑580RD DVI Line Transmitter / Receiver 8

Connecting to TP‑580TD, TP‑580RD via RS-232

The TP‑580TD and TP‑580RD each feature an RS-232 3-pin terminal block connector that

can be used to:

•Extend serial communication data between serial-enabled devices that are connected to

the TP‑580TD and TP‑580RD.

•Upgrade the firmware of the TP‑580TD and/or TP‑580RD using a Laptop, PC, or other

serial-enabled controller devices.

Connect the RS-232 terminal block on the rear panel of the TP‑580TD, TP‑580RD to a

PC/controller, as follows (see Figure 4):

•TX pin to Pin 2

•RX pin to Pin 3

•GND pin to Pin 5

Figure 4: RS-232 Connection

Otros manuales para TP-580TD

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Kramer

Kramer

Kramer VP-300THD Manual de usuario

Kramer

Kramer 675T Manual de usuario

Kramer

Kramer 614T Manual de usuario

Kramer

Kramer TP-580CT Manual de usuario

Kramer

Kramer Cobra TS2 Manual de usuario

Kramer

Kramer 622T Manual de usuario

Kramer

Kramer 671T Manual de usuario

Kramer

Kramer WP-871xr Manual de usuario

Kramer

Kramer TP-210 Manual de usuario

Kramer

Kramer WP-20 Manual de usuario

Kramer

Kramer TA-110HD Manual de usuario

Kramer

Kramer 691 Manual de usuario

Kramer

Kramer TP-752T Manual de usuario

Kramer

Kramer 611T Manual de usuario

Kramer

Kramer WP-110xl Manual de usuario

Kramer

Kramer TP-102HD Manual de usuario

Kramer

Kramer Cobra TS2 Manual de usuario

Kramer

Kramer TP-210 Manual de usuario

Kramer

Kramer TP-594Txr Manual de usuario

Kramer

Kramer DigiTOOLS KW-11T Manual de usuario

Kramer

Kramer Cobra T2 Manual de usuario

Kramer

Kramer VA-1USB-T Manual de usuario

Kramer

Kramer VP-5R Manual de usuario

Kramer

Kramer SID-X2N Manual de instalación y operación

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario