Kramer TP-583Txr Manual de usuario

P/N: 2900-301246 Rev 1 www.KramerAV.com

USER MANUAL

MODELS:

TP-583Txr,TP-583T

HDMI Line Transmitter

TP-583Rxr,TP-583R

HDMI Line Receiver

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Contents

Contents

Introduction 1

Getting Started 1

Overview 2

Typical Applications 3

Defining TP-583Txr and TP-583T 4

Defining TP-583Rxr and TP-583R 5

Mounting TP-583Txr 6

Connecting the extenders 7

Connecting to an Extender via RS-232 8

Wiring HDBT RJ-45 Connectors 8

Controlling TP-583Txr 9

Technical Specifications 10

TP-583Txr and TP-583Rxr 10

TP-583T and TP-583R 11

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Introduction

Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world

of unique, creative, and affordable solutions to the vast range of problems that confront the

video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we

have redesigned and upgraded most of our line, making the best even better!

Getting Started

We recommend that you:

•Unpack the equipment carefully and save the original box and packaging materials for

possible future shipment.

•Review the contents of this user manual.

Go to www.kramerav.com/downloads/TP-583Txr to check for up-to-date user manuals,

application programs, and to check if firmware upgrades are available (where appropriate).

Achieving the Best Performance

•Use only good quality connection cables (we recommend Kramer high-performance,

high-resolution cables) to avoid interference, deterioration in signal quality due to poor

matching, and elevated noise levels (often associated with low quality cables).

•Do not secure the cables in tight bundles or roll the slack into tight coils.

•Avoid interference from neighboring electrical appliances that may adversely influence

signal quality.

•Position your Kramer extender away from moisture, excessive sunlight and dust.

Safety Instructions

Caution:

•This equipment is to be used only inside a building. It may only be connected to other

equipment that is installed inside a building.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•To ensure continuous risk protection, replace fuses only according to the rating

specified on the product label which located on the bottom of the unit.

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Introduction

Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce

the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected

and recycled. To comply with the WEEE Directive, Kramer Electronics has made

arrangements with the European Advanced Recycling Network (EARN) and will cover any

costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on

arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular

country go to our recycling pages at www.kramerav.com/support/recycling.

Overview

The devices described in this user manual are generally referred to as TP-583Txr (HDMI

Line Transmitter) and/or TP-583Rxr (HDMI Line Receiver) or generally an extender. A

device is named specifically only when a device-specific feature is described.

Congratulations on purchasing your Kramer TP-583Txr, TP-583Rxr, TP-583T and/or

TP-583R.

TP-583Txr / TP-583Rxr are a high-performance, HDBaseT transmitter/receiver system for 4K

HDR HDMI™, RS-232 and IR signals over twisted pair.

TP-583Txr converts all input signals into the transmitted HDBaseT signal. TP-583Rxr

converts the HDBaseT signal and outputs it to its HDMI and control ports.

The extenders are compatible with standard HDBaseT-compliant extenders up to 4K@30Hz

(4:4:4) video resolutions.

TP-583Txr and TP-583Rxr extend video signals up to 100m (330ft) at 4K@60Hz (4:4:4)

video resolution, up to 180m (590ft) at 4K@30Hz (4:4:4), and up to 200m (650ft) at HD video

resolution over Kramer copper cables.

TP-583T and TP-583R extend video signals to up to 70m (230ft) at up to 4K@60Hz (4:4:4)

video resolutions, over Kramer copper cables.

The extenders provide exceptional quality, advanced and user-friendly operation, and flexible

control.

Exceptional Quality

•High Performance Standard Extender –Professional HDBaseT extender for providing

long-reach signals over twisted-pair copper infrastructures. It employs low-level video

compression technology that delivers visually lossless performance for 4K@60 (4:4:4)

and HDR signals with near-zero latency. This high-quality compressed signal is

extended to almost double the extension reach of the uncompressed signal.

•I-EDIDPro™ Kramer Intelligent EDID Processing™ – Intelligent EDID pass-through

algorithm that ensures plug and play operation for HDMI source and display systems.

•Multi-channel Audio Extension –Up to 32 channels of digital stereo uncompressed

signals for supporting studio-grade surround sound.

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Introduction

•HDMI Signal Extension –HDMI 2.0 and HDCP 2.2 compliant. Supports HDR, deep

color, x.v.Color™, lip sync, HDMI uncompressed audio channels, Dolby TrueHD,

DTS-HD, 2K, 4K, and 3D as specified in HDMI 2.0. EDID and CEC signals are passed

through from the source to the display.

Advanced and User-friendly Operation

•Future-proof, Standard Extender –Standard HDBaseT extender, backwards compatible

with other standard HDBT extenders. It extends either compressed or uncompressed

HDBaseT signal, by auto-adapting to the compression capabilities of its connected

extender. This enables it to be connected to any market-available HDBaseT-compliant

extension product.

•Intelligent Compression Handling –Automatically detects a standard HDBaseT extender

without compression and disables the compression to extend the signal in compliance

with the detected extender.

•Cost-Effective Maintenance –Status LED indicators for HDMI and HDBT ports facilitate

easy local maintenance and troubleshooting. Local firmware upgrade via RS-232

connection ensures lasting, field-proven deployment.

Flexible Connectivity

•Bidirectional RS-232 Extension –Serial interface data flows in both directions, providing

data transmission and device control.

•Bidirectional Infrared Extension –IR interface data flows in both directions, enabling

remote control of peripheral devices located at either end of the extended line.

•Easy Installation –Compact DigiTOOLS® fan-less enclosure for dropped-ceiling

mounting, or side-by-side mounting of 3 units in a 1U rack space with the recommended

rack adapter.

Typical Applications

TP-583Txr is ideal for the following typical applications:

•Long-distance AV signal extension for multi-room, large dividable auditoriums and

lecture hall connectivity.

•AV extension in conference rooms, boardrooms, control rooms, hotels and large church

facilities.

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Defining TP-583Txr and TP-583T

Defining TP-583Txr and TP-583T

This section defines TP-583Txr and TP-583T.

Figure 1: TP-583Txr HDMI Line Transmitter

Feature

Function

IN LED

Lights green when an active source device input signal is detected.

OUT LED

Lights green when an active, far-end sink (acceptor) connection is detected

via the HDBT link.

LINK LED

Lights green when an HDBT link is established with the HDBaseT receiver.

ON LED

Lights green when the device receives power.

LINE RJ-45 Connector

Connect to the RJ-45 HDBT LINE connector on a receiver (for example,

TP-583Rxr/R, TP-580Rxr/Rand so on).

HDMI™ IN Connector

Connect to an HDMI source.

SETUP DIP-switches

Set the operation DIP-switches.

RS-232 (G, Rx, Tx)

3-pin Terminal Block

Connector

Connect to a controller device (for example, SL-240C) to serially control a

remote device (for example, the HDMI OUT acceptor) that is connected to

TP-583Rxr/TP-583R.

IR 3.5mm Mini Jack

Connector

Connect to an external infrared emitter / sensor.

12V DC Power

Connector

12V DC connector for powering the unit.

1 2 3 4 5 6 7 8 9 10

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Defining TP-583Rxr and TP-583R

Defining TP-583Rxr and TP-583R

This section defines TP-583Rxr and TP-583R.

Figure 2: TP-583Rxr HDMI Line Receiver

Feature

Function

IN LED

Lights green when an active, far-end source device input signal is

detected via the HDBT link.

OUT LED

Lights green when an active sink (acceptor) connection is detected.

LINK LED

Lights green when an HDBT link is established with the HDBaseT

transmitter.

ON LED

Lights green when the device receives power.

LINE RJ-45 Connector

Connect to the RJ-45 HDBT LINE connector on a transmitter (for

example, TP-583Txr/T, TP-580Txr/Tand so on).

HDMI™OUT Connector

Connect to an HDMI acceptor.

SETUP DIP-switches

Set the operation DIP-switches.

RS-232 (G, Rx, Tx) 3-pin

Terminal Block Connector

Connect to a serially controlled device (for example, the HDMI OUT

acceptor) to enable its control by a remote controller device (for

example, SL-240C) that is connected to TP-583Txr/TP-583T.

IR 3.5mm Mini Jack

Connector

Connect to an external infrared emitter / sensor.

12V DC Power Connector

12V DC connector for powering the unit.

11 12 13 14 15 16 17 18 19 20

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Mounting TP-583Txr

Mounting TP-583Txr

This section provides instructions for mounting TP-583Txr. Before installing, verify that the

environment is within the recommended range:

•Operation temperature –0to 40C (32 to 104F).

•Storage temperature –-40to +70C (-40 to +158F).

•Humidity –10% to 90%, RHL non-condensing.

Caution:

•Mount TP-583Txr before connecting any cables or power.

Warning:

•Ensure that the environment (e.g., maximum ambient temperature & air flow) is

compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be used for avoiding

overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

To mount the TP-583Txr on a rack

Mount the unit in a rack using the recommended rack adapter

(see www.kramerav.com/product/TP-583Txr)

To mount the TP-583Txr on a table or shelf

•Attach the rubber feet and place the unit on a flat surface.

•Fasten a bracket (included) on each side of the unit and attach it to

a flat surface.

For more information go to www.kramerav.com/downloads/TP-583Txr

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Connecting the extenders

Connecting the extenders

Always switch off the power to each device before connecting it to your

HDMI Line Transmitter / HDMI Line Receiver. After connecting your

HDMI Line Transmitter / HDMI Line Receiver, connect its power and then switch on the

power to each device.

TP-583Txr / TP-583Rxr and TP-583T / TP-583R are connected in the same way.

Figure 3: Connecting the extenders

To connect the TP-583Txr and TP-583Rxr as illustrated in the example in Figure 3:

1. On TP-583Txr connect an HDMI source (for example, a Blu-ray player) to the HDMI IN

connector .

2. On TP-583Rxr connect the HDMI OUT connector to an HDMI acceptor (for example,

a display).

3. Connect the LINE RJ-45 connector on TP-583Txr to the LINE RJ-45 connector on

TP-583Rxr .

4. Extend RS-232 signals (for example, control the display via a room controller on the

transmitter side):

▪On TP-583Txr connect a controller (for example, SL-240C room controller) to the

RS-232 3-pin terminal block connector .

▪On TP-583Rxr connect the RS-232 3-pin terminal block connector to the RS-232

control port on the display.

5. Extend IR signals (for example, control the Blu-ray via its IR remote control transmitter

from the receiver side).

▪On TP-583Txr connect the IR 3.5mm mini jack to an IR emitter cable and

connect it to the Blu-ray IR sensor.

▪On TP-583Rxr connect the IR 3.5mm mini jack to an IR sensor (receiver) cable.

6. Connect the power adapters to both extenders and to the mains electricity (not shown in

Figure 3).

Kramer Electronics Ltd.

TP-583Txr, TP-583Rxr, TP-583T, TP-583R –Connecting the extenders

Connecting to an Extender via RS-232

You can connect to the extender (for example, TP-583Txr) via an RS-232 connection to a

room controller (for example, SL-240C with Kramer Control) to control a remote serially

controlled device that is connected to the other, paired, extender device.

Connect the RS-232 terminal block on the rear panel of the extender (for example,

TP-583Txr) to an RS-232 9-pin D-sub serial port on a laptop/controller, as follows:

•Pin 2 to the TX pin on the TP-583Txr RS-232

terminal block

•Pin 3 to the RX pin on the TP-583Txr RS-232

terminal block

•Pin 5 to the G pin on the TP-583Txr RS-232

terminal block

Wiring HDBT RJ-45 Connectors

This section defines the HDBT CAT cable pinout, using a straight pin-to-pin cable with RJ-45

connectors.

For HDBT cables, it is recommended that the cable ground shielding be connected/soldered

to the connector shield.

EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

Otros manuales para TP-583Txr

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Transmisor de Kramer

Kramer

Kramer TP-590Txr Manual de usuario

Kramer

Kramer RC-116 Manual de usuario

Kramer

Kramer TP-752T Manual de usuario

Kramer

Kramer TP-580TD Manual de usuario

Kramer

Kramer TP-112HD Manual de usuario

Kramer

Kramer VP-300THD Manual de usuario

Kramer

Kramer F-121UK Manual de usuario

Kramer

Kramer WP-110xl Manual de usuario

Kramer

Kramer 675T Manual de usuario

Kramer

Kramer 610T Manual de usuario

Kramer

Kramer SID-X1N Manual de usuario

Kramer

Kramer SWT3-41-U-T Manual de usuario

Kramer

Kramer DigiTOOLS KW-11T Manual de usuario

Kramer

Kramer TP-112HD Manual de usuario

Kramer

Kramer EXT3-C-WP-XR-T Manual de usuario

Kramer

Kramer 611T Manual de usuario

Kramer

Kramer TP-594Txr Manual de usuario

Kramer

Kramer VP-428H2 Manual de usuario

Kramer

Kramer TP-185 Manual de usuario

Kramer

Kramer VP-5R Manual de usuario

Kramer

Kramer WP-110xl Manual de usuario

Kramer

Kramer TP-121EDID Manual de usuario

Kramer

Kramer DIP-20 Manual de usuario

Kramer

Kramer KW-14T Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario