Kramer VS-622DT Manual de usuario

-622DT Enhanced Quick Start (P/N: 2900-300856QS REV 2)

P/N:

2900- 300856QS

Rev:

Scan for full manual

VS-622DT Quick Start Guide

This guide helps you install and use your VS-622DT for the first time.

Go to www.kramerav.com/downloads/VS-622DT to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

VS-622DT

6x2 HDMI / HDBT Audio Matrix Switcher 1 Quick start guide 1 Set of rack ears

1 Power cord 4 Rubber feet

Step 2: Get to know your VS-622DT

# Feature Function

IR LED

Lights red when the unit accepts IR remote commands.

IR Receiver

Receives signals from the remote control transmitter.

3 ON LED Lights when the unit is powered.

4 TO OUT 1 Press to select an input to switch to OUT 1 (from 1 to 6).

TO OUT 2

Press to select an input to switch to OUT 2 (from 1 to 6).

LOCK Button

Press to lock the front panel buttons.

7 SWAP Button Press to swap

between audio outputs.

8 PATTERN Button Press to activate the test pattern generator. When the generator is active, press one of the input

buttons to select a test pattern.

EDID Button

Press to capture the EDID.

10 Output 1 Audio Buttons VOL +: Increase output 1 volume.

VOL -: Decrease output 1 volume.

MUTE: Mute output 1 audio signal.

11 Output 2 Audio Buttons VOL +: Increase output 2 volume.

VOL -: Decrease output 2 volume.

MUTE: Mute output 1 audio signal.

12 HDBT RS-232 LEDs Indicates data transmission from a controller to a device connected to the transmitter via

HDBT OUT 1:

TX 1: Lights green when data is transmitted via HDBT OUT 1.

RX 1: Lights red when data is received on HDBT OUT 1.

13 EXTERNAL (Controller)

LEDs

Indicates data transmission via the RS-232 port (item 29) to the VS-622DT:

TX 2: Lights green when data is transmitted on the RS-232 port.

RX 2: Lights red when data is received on the RS-232 port.

IR OUTPUT LEDs (1 to 4)

Lights green when the relevant IR port transmits data.

15 GPI/O LEDs (1 to 2) Lights green when the port is triggered.

16 RELAY LEDs (1 to 2) Lights green when the relay is closed.

# Feature Function

17 HDBT IN 1 RJ-45 Connectors (1 to 2) Connect to an HDBT transmitter (for example,

TP-580Txr

18 POE STATUS and LINK LEDs (for HDBT IN 1 to 2

and HDBT OUT 1)

Light when PoE is available and a link is established.

Control RS-232 3-pin Terminal Block

Connect to the serial controller to control the device.

20 AUDIO OUT Balanced Stereo Audio 5-pin Terminal

Block Connectors (1 to 2)

Connect to an analog audio acceptor.

21 SETUP DIP-switches Used to set the device behavior.

22 INPUT HDMI Connectors (3 to 6) Connect to HDMI source (from 1 to 8).

ETHERNET RJ-45 Connector

Connect to a remote network controller via a LAN.

HDBT OUT1 RJ-45 Connector

Connect to an HDBT receiver (for example, TP-580Rxr)

25 HDMI OUT 2 Connector Connect to an HDMI acceptor.

26 RESET Switch Press and hold while powering on the device to reset to factory

default parameters.

27 Hi-Z OUT Terminal Block Connectors Lo-Z – connect stereo output to Lo-Z speakers:

L+ and L- to the left speaker; R+R- to the right speaker.

Hi-Z (70V or 100V) – connect Hi-Z and COM to mono Hi-Z

speakers.

PROG Mini USB Connector

Connect to a PC to perform firmware upgrade.

29 RS-232 (G, Rx, Tx) Terminal Block Connector Connect to an RS-232 controlled device.

30 MAESTRO CONTROL 9-pin Terminal Block

Connectors

Connect to configurable buttons (configured via the Automation

page), such as the

RC-21TB

IR OUTPUT 2-pin Terminal Block Connectors (1 to 4)

Connect to IR blasters/emitters using cables up to 80m (260ft) long.

32 GPI/O 2-pin Terminal Block Connectors (1 to 2) Connect to controllable sensors or devices (for example, motion

sensors). This port can be configured as a digital input, digital

output, or analog input.

33 RELAY 2-pin Terminal Block Connectors (1 to 2) Connect to a relay controllable device, (for example, a motorized

projection screen).

34 Mains Power Connector, Fuse, and Switch Connect to the mains supply.

Step 3: Install VS-622DT

Install VS-622DT using one of the following methods:

•Remove the three screws from each side of the unit, reinsert those screws through the

rack ears and mount on a 19" rack.

•Attach the rubber feet and place the unit on a flat surface.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VS-622DT. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the VS-622DT.

RJ-45 Pinout:

Audio output pinout:

For the Ethernet connector, see the wiring diagram below: To a balanced stereo

audio acceptor:

To an unbalanced

stereo audio

acceptor:

PIN EIA /TIA 568B

PIN Wire Color

1 Orange / White

2 Orange

3 Green / White

4 Blue

5 Blue / White

6 Green

7 Brown / White

8 Brown

For optimum range and performance use the recommended Kramer

cables available at www.kramerav.com/product/VS-622DT.

DIP-switch setup

A switch that is down is on; a switch that is up is off. By default, all the switches are up (off).

# Feature Description

1 HDCP support on inputs On (down)—Disable HDCP support on all inputs.

Off (up)—Enable HDCP support which is defined by P3000

commands.

2 Video mode switching

Output 1

On (down)—Auto.

Off (up)—Manual.

3 Last connected/Priority

mode Output 1

When DIP-switch 2 is set to Auto (ON):

On (down)—Enable Last Connected mode.

Off (up)—Enable Priority mode where the priority of each input

is defined by the input number, (1 is the highest priority).

4 Video mode switching

Output 2

On (down)—Auto.

Off—Manual.

5 Last connected/Priority

mode Output 2

When DIP-switch 4 is set to Auto (ON):

On (down)—Enable Last-connected mode.

Off (up)—Enable Priority mode where the priority of each input

is defined by the input number, (1 is the highest priority).

N/A

7 Range mode for

HDBT IN 1

On (down) – HDBaseT Ultra-long range (provides increased

range at a reduced bandwidth).

Off (up) – Normal range (default).

8 Range mode for

HDBT IN 2

On (down) – HDBaseT Ultra-long range (provides increased

range at a reduced bandwidth).

Off (up) – Normal range (default).

Step 5: Connect the power

Connect the power cord to VS-622DT and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Operate the VS-622DT

Web pages:

-232 and Ethernet:

RS-232/Ethernet

Baud Rate: 115,200 Parity: None

Data Bits: 8 Command Format: ASCII Protocol 3000

Stop Bits:

Example (Route input 1 to output 1):

#VID1> 1<cr>

Ethernet Parameters

IP Address:

192.168.1.39

Default UDP Port #:

50000

Subnet Mask: 255.255.0.0

Default Gateway: 192.168.0.1

Full Factory Reset

OSD: Front panel buttons: power off the device, press and hold the

RESET button for 3 seconds while powering the device, and

then release.

Protocol 3000:

“#factory” command.

Web Pages:

In the Device Settings page, General tab, click Factory reset.

Technical Specifications

Inputs

2 HDBT

On female RJ-45 connectors

4 HDMI

On female HDMI connectors

Outputs

1 HDBT

On a female RJ-45 connector

1 HDMI

On a female HDMI connector

2 Stereo Balanced Audio

On 5-pin terminal block connectors

1 Stereo or 1 Mono Speaker

On a 4-pin large terminal block

Ports 1 Ethernet

On an RJ-45 female connector

2 RS-232

On 3-pin terminal blocks

1 USB

On a mini USB connector

4 IR

On 2-pin terminal block connectors

2 GPI/O

On 2-pin terminal block connectors

2 Relays

On 2-pin terminal block connectors

Video

Max Resolution

Up to 4K@60Hz UHD (4:2:0)

Compliance

HDMI 1.4 and HDCP 1.4

Reach Extended

Up to 130m (430ft)

Controls

Front Panel

Input selection buttons, swap, EDID, lock and audio control buttons

Power, RS-232, IR, GPI/O and relay indication LEDs

Remote

RS-232

Ethernet

Web pages

IR remote control transmitter

Power

Consumption

100-240V AC, 210VA max.

Cooling

Fan Ventilation

Environmental

Conditions

Operating Temperature

0° to +40°C (32° to 104°F)

Storage Temperature

-40° to +70°C (-40° to 158°F)

Humidity

10% to 90%, RHL non-condensing

Regulatory

Compliance

Safety

Environmental

RoHs, WEEE

Enclosure

Size

19”, 1U

Type

Aluminum

General

Net Dimensions (W, D, H)

43.64cm x 23.7cm x 4.36cm (17.18" x 9.3" x 1.72")

Shipping Dimensions (W, D, H)

52.5cm x 33cm x 10.7cm (20.7" x 13" x 4.21")

Net Weight

2.6kg (5.7lbs) approx.

Shipping Weight

3.7kg (8.2lbs) approx.

Accessories

Included

Power cord

Otros manuales para VS-622DT

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Conmutador de matriz de Kramer

Kramer

Kramer XL 1608V4S Manual de usuario

Kramer

Kramer VS-44HDCP Manual de usuario

Kramer

Kramer VS-82HDxl Manual de usuario

Kramer

Kramer Sierra Video 3232V3S Manual de usuario

Kramer

Kramer VS-88HC Manual de usuario

Kramer

Kramer VS-48HDxl Manual de usuario

Kramer

Kramer VS-6464DN Manual de usuario

Kramer

Kramer 6464V5XL Manual de usuario

Kramer

Kramer AFM-20DSP-AEC Manual de usuario

Kramer

Kramer VS-66HDMI Manual de usuario

Kramer

Kramer VS-88H Manual de usuario

Kramer

Kramer VP-2x2 Manual de usuario

Kramer

Kramer VP-32XLN Manual de usuario

Kramer

Kramer Sierra Video 1608V3 Manual de usuario

Kramer

Kramer VS-6EII Manual de usuario

Kramer

Kramer VP-8x8AK Manual de usuario

Kramer

Kramer TailorMade Manual de usuario

Kramer

Kramer VS-44HDXI Manual de usuario

Kramer

Kramer VS-88HDCPxl Manual de usuario

Kramer

Kramer VS-211H Manual de usuario

Kramer

Kramer VS-24x1 Manual de usuario

Kramer

Kramer VS-1616DN-MD Manual de usuario

Kramer

Kramer VP-16x18AK Manual de usuario

Kramer

Kramer VP-16X18AK/110V Manual de usuario

Manuales populares de Conmutador de matriz de otras marcas

Broadcast Tools

Broadcast Tools SS 8.2 Manual de usuario

Altimium

Altimium MATF32 Manual de usuario

ALFAtron

ALFAtron ALF-MUK44N Manual de usuario

Monoprice

Monoprice Blackbird 15377 Manual de usuario

PTN

PTN FMX12 Manual de usuario

CYP

CYP nT15GX01 Manual de usuario

TESmart

TESmart HMA0402A40 Manual de usuario

Octava

Octava HD4XSTPMX Manual de usuario

Intelix

Intelix FLX-88 Instrucciones de funcionamiento

Roland

Roland XS-1HD Manual de usuario

Atlona

Atlona AT-HDMI-22M Manual de usuario

Link

Link HD8X8 Manual de usuario

AMX

AMX AVS-OP-2020-117 Instrucciones y recetas

Lindy

Lindy 38042 Manual de usuario

Extron electronics

Extron electronics MTPX Plus Series Manual de usuario

Key Digital

Key Digital Champion KD-16x16CS Manual de usuario

Shinybow USA

Shinybow USA SB-8811 Manual de usuario

Optimus

Optimus Compact Manual de usuario