Johnson Controls System 350 Y350R Manual de servicio

FANs 930, 930.5, 125

Product/Technical Bulletin Y350R

Issue Date 0598

Part No. 24-7664-214, Rev. D

Code No. LIT-930090

The Y350R is a rectified Class 2, 24 VAC power

supply module designed specifically for use with

System 350™ Modular Control Systems.

As with all System 350 products, the Y350R is housed

in a compact NEMA 1, high-impact plastic enclosure.

The modular design provides easy, plug-in

connections for quick installation and future

expandability.

Figure 1: Y350R Power Module

System 350Y350R Power Module

Features and Benefits

❑Modular Design Enables stage, display, and power modules to be

purchased and installed as necessary

❑Plug-in Connectors and

35 mm DIN Rail Mounting Eliminates wiring between modules and reduces

installation costs

❑Accepts Input Voltages of

120 or 240 VAC, 50/60 Hz Reduces inventory by encompassing the primary

voltage requirements

2 Y350R Power Module Product/Technical Bulletin

pplication

The Y350R Power Module provides the power

necessary to operate all System 350 controls and

add-on modules. For system capabilities, see Table 1.

Table 1: Maximum Number of Add-on

Modules when Powered by a Y350R

Control

Module Stage Module Display

Module

A350A

A350B

A350E

9 S350A’s or S350C’s

6 S350A’s or S350C’s with

1 S350P

4 S350A’s or S350C’s with

2 S350P’s

1 D350

A350P 4 S350A’s or S350C’s

2 S350A’s or S350C’s with

1 S350P

1 D350

A350R

A350S 9 S350A’s or S350C’s

6 S350A’s or S350C’s with

1 S350P

4 S350A’s or S350C’s with

2 S350P’s

2 D350

W351A 5 S351’s 1 D351

W351P 4 S351’s 1 D351

P352A 5 S352’s 1 D352

P352P No additional stages available 1 D352

R353 5 S353’s No

display

available

All System 350 add-on modules snap on to a DIN rail

and plug into the control and to each other via 5-pin

connectors. Add-on modules can be arranged in any

order and there is no wiring required to interconnect

the System 350 components.

peration

The Y350R operates from 240 VAC or 120 VAC

power. A 24 VAC, Class 2, step-down transformer

brings the voltage to a level which the System 350

modules will accept. There are no adjustments for the

power module.

IMPORTANT: All Series Y350R Power Modules

are designed for use only in

conjunction with operating

controls. Where an operating

control failure would result in

personal injury and/or loss of

property, it is the responsibility of

the installer to add devices

(safety, limit controls) that protect

against, or systems (alarm,

supervisory systems) that warn

of, control failure.

imensions

Mounting Slot (4)

for No. 6 Screws

Y350

Conduit

Hole

0.145

3.68

2.94

DIN Rail

Mount 2.40

1.20

0.85

21.6

0.42

1.56

0.5

5.00

127

2.40

0.875

Figure 2: Y350R Dimensions, mm/in.

nstallation and Wiring

The Y350R case has provisions for mounting to a

standard 35 mm DIN rail, or can be mounted using the

four key slot mounting holes located in the rear of the

case.

Mount System 350 modules in any convenient location

using either the DIN rail mounts or the mounting holes

located on the back of the control case. The

components are not position sensitive, but should be

mounted so they can be easily wired and adjusted.

Y350R Power Module Product/Technical Bulletin 3

IMPORTANT: All wiring must be installed to

conform to the National Electrical

Code and local regulations.

1. Secure the module to the DIN rail, wall, or panel.

WARNING:Electrical Shock Hazard.

Disconnect power supply before

modules are interconnected and

wiring connections are made to

avoid possible electrical shock or

damage to the equipment.

2. Connect input wiring to the Y350R power module.

Strip approximately 3/8 inch from the wire

insulation, insert the wire under each terminal

screw, and tighten. (See Figure 3.)

Note: If conduit is used when installing System 350

components, be sure to connect the hub to the

conduit before the hub is secured to the

enclosure.

Module

Connector

Module

Connector

240 VAC COM 120 VAC

Power Input Terminals

Figure 3: Interior of the Y350R Power

Module

heckout Procedure

Before applying power, make sure installation and

wiring connections are according to job specifications.

After necessary adjustments and electrical

connections have been made, put the system in

operation and observe at least three complete

operating cycles before leaving the installation.

roubleshooting

If the control system does not function properly and

the Y350R is suspect, proceed as follows:

1. Connect a Digital Voltmeter (DVM) between the

24V (+) and COM (-) terminals located on the

control module’s left-side connector. (Terminal

designations are marked on the control module.)

2. Select DC volts on the DVM and verify that the

voltage is between 16 and 38 VDC. If the DVM

reading is within range, the Y350R is functioning

properly.

Note: Consult the

Troubleshooting

section of the

appropriate control bulletin for a complete

system troubleshooting procedure.

3. If the DVM reading is not within the indicated

voltage range, check wiring and correct if

necessary. If the wiring is correct and the reading

remains out of range, replace the Y350R.

epairs and Replacement

Field repairs or calibration must not be made.

Replacement modules are available through the

nearest Johnson Controls representative. (See Table

2.)

rdering Information

Table 2: Product Available

Item Product Code Description

Power Module Y350R-1C Rectified, Class 2, 24 VAC Power Supply

4 Y350R Power Module Product/Technical Bulletin

pecifications

Product Y350R Power Module

Input Voltage 120/240 VAC, 50/60 Hz

Output Voltage Rectified 24 VAC, 10 VA, Class 2

Material Case and cover: NEMA 1 high-impact plastic

Ambient Temperature Operating: -34 to 66°C (-30 to 150°F)

Shipping: -40 to 85°C (-40 to 185°F)

Ambient Humidity 0 to 95% RH non-condensing

Mounting Wall or DIN rail

Agency Listing UL Guide No. XAPX, File E27734

CUL Guide No. XAPX7, File E27734

CSA Class No. 4813 02, File LR948

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications,

consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products.

Controls Group

507 E. Michigan Street

P.O. Box 423

Milwaukee, WI 53201 Printed in U.S.A.

Otros manuales de Unidad de control de Johnson Controls

Johnson Controls

Johnson Controls Mercury 3 Series Manual

Johnson Controls

Johnson Controls Penn System 450 Series Manual de usuario

Johnson Controls

Johnson Controls Tyco RV-1A Manual de usuario

Johnson Controls

Johnson Controls System 450 Series Manual de usuario

Johnson Controls

Johnson Controls Tyco DV-5a Series Manual de usuario

Johnson Controls

Johnson Controls IOM3711 Manual de usuario

Johnson Controls

Johnson Controls Penn A19K Series Manual de usuario

Johnson Controls

Johnson Controls S300 Series Instrucciones de montaje

Johnson Controls

Johnson Controls Tyco PRV-1A Manual de usuario

Johnson Controls

Johnson Controls VG8000V Series Manual de usuario

Johnson Controls

Johnson Controls tyco AMD-2 Manual de usuario

Johnson Controls

Johnson Controls Tyco RSV-1 Manual de usuario

Johnson Controls

Johnson Controls tyco AMD-1 Manual de usuario

Johnson Controls

Johnson Controls TYCO DPV-1 Manual de instrucciones

Johnson Controls

Johnson Controls M300CJ Manual de usuario

Johnson Controls

Johnson Controls H Series Manual de usuario

Johnson Controls

Johnson Controls PENN P470 Manual

Johnson Controls

Johnson Controls P352PN-2 Manual de usuario

Johnson Controls

Johnson Controls S1-TTSCC01 Guía de inicio rápido

Johnson Controls

Johnson Controls VP1000 Series Manual de usuario

Johnson Controls

Johnson Controls M300CJ-R Manual de usuario

Johnson Controls

Johnson Controls Tyco DV-5a Series Manual de usuario

Johnson Controls

Johnson Controls A19ZBC Series Manual de servicio

Johnson Controls

Johnson Controls VP140 L Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario