Johnson Controls CKM-F8P Manual
24-10707-147 Revision C
December 2017
P2000
Security Management System
CKM-F8P
power distribution module
hardware
installation
Copyright 2017
Johnson Controls
All Rights Reserved
No part of this document may be reproduced without the prior permission of Johnson Controls.
If this document is translated from the original English version by Johnson Controls, all reasonable
endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable
for any translation errors contained herein or for incidental or consequential damages in connection
with the furnishing or use of this translated material.
Due to continuous development of our products, the information in this document is subject to
change without notice. Johnson Controls shall not be liable for errors contained herein or for
incidental or consequential damages in connection with furnishing or use of this material. Contents
of this publication may be preliminary and/or may be changed at any time without any obligation to
notify anyone of such revision or change, and shall not be regarded as a warranty.
Other Manufacturers’ Documentation
Johnson Controls does not duplicate documentation of other equipment manufacturers. When
necessary, Johnson Controls provides documentation that supplements that of other manufacturers.
When unpacking your equipment, keep all original manufacturer documentation for future
reference.
Technical Support
For factory technical support, Johnson Controls authorized field technicians or authorized dealer
representatives can contact Global Security Solutions Technical Support by phone at
can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.
End users and customers should contact their local Johnson Controls branch or authorized dealer
for any of their support needs (technical support, maintenance contracts, on-site field support,
P2000 Software Service Agreements, Service Partnerships, and so on). Visit
http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.
For material returns contact the branch if the material was purchased through a Johnson Controls
branch or through the Product Sales Operations Team, if ordered through the Advanced Order
Management System (AOMS) and follow the RMA process; or contact the authorized dealer
representative where the material was purchased directly.
Acknowledgment
Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and
product names are trademarks or registered trademarks of their respective owners.
Declaration of Conformity
United States: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Canada: CAN ICES-3 (A)/NMB-3(A)
CKM-F8P Hardware Installation Manual
24-10707-147 Rev. C
1
CKM-F8P POWER DISTRIBUTION MODULE
This document provides hardware installation and setup instructions for the
CKM-F8P power distribution module. This document consists of the following
sections:
•General Information on page 1
•Mounting Information on page 3
•Wiring Information on page 4
•Specifications on page 7
GENERAL INFORMATION
The CKM-F8P power distribution module provides eight zones of fused or
PTC-protected power distribution with Fire Alarm Interface (FAI) control. The
CKM-F8P accepts one or two DC power inputs, either of which are available
on any output zone. Each output can be enabled for FAI, disabled for FAI, or set
for continuous output.
Figure 1: CKM-F8P Hardware
CKM-F8P Hardware Installation Manual
24-10707-147 Rev. C
2
Component Description
Component Names (Click on a link for full description)
1
2
3
4
5
FlexIO Connectors
B1 Connectors (J1 and J4)
B2 Connectors (J3 and J5)
Output Selection Jumpers (JP1 – JP8)
B2 LED (D4) – Green
6
7
8
9
10
B1 LED (D3) – Green
BR Connectors (J3 and J6)
Zone Outputs (Out1 – Out8)
FAI LED (D11) – Red
Optional Output Fuses (F1 – F8)
Component Description
FlexIO Connectors These connectors pass the FAI and Fault signals to and from the
CKM-F8P board and pass the FlexIO bus on to other accessory
boards in the system.
B1 Connectors (J1
and J4)
Faston connectors for the B1 voltage bus in the system.
The voltage on the B1 bus comes from the DC1 Faston connector
of a power supply. This voltage will be directed to any outputs
whose output selection jumper is set to one of the B1 positions.
B2 Connectors (J3
and J5)
Use these Faston connectors for the B2 voltage bus in the system.
The voltage on the B2 bus comes from the DC1 Faston connector
of the power supply. This voltage will be directed to any outputs
whose output selection jumper is set to the B2 position. If you are
using the CKM-F8P in a single voltage system, leave these Faston
connectors unused.
Output Selection
Jumpers (JP1 –
JP8)
Output selection jumpers select the voltage bus input for the output
and the FAI operation for the zone. Jumper numbers correspond
with the zone number (for example, JP1 is the jumper for OUT1).
Possible settings are as follows:
• Pos. 1 (Top) - Continuous output of B1 voltage
• Pos. 2 B1 - Enables voltage on FAI
• Pos. 3 B1 - Disables voltage on FAI
• Pos. 4 - Constant output of B2 voltage
• Pos. 5 B2 - Enables voltage on FAI
• Pos. 6 (Bot.) B2 - Disables voltage on FAI
• Removed - Disables output
B2 LED (D4) –
Green
The B2 LED lights when voltage is available on the B2 bus.
Note: This LED does not light in a single voltage system.
B1 LED
(D3) – Green
The B1 LED lights when voltage is available on the B1 bus.
CKM-F8P Hardware Installation Manual
24-10707-147 Rev. C
3
MOUNTING INFORMATION
Mount the CKM-F8P board to an enclosure using the four snap-in standoffs
supplied.
To mount the CKM-F8P board to an enclosure:
1. Locate the appropriate mounting holes in the enclosure and snap the
standoffs into the holes.
2. Align the board mounting holes with the standoffs and snap the board
onto the standoffs. Be sure the board is properly oriented.
Figure 2: Mounting the CKM-F8P Board to an Enclosure
BR Connectors
(J3 and J6)
The DC Common bus in the system. All boards in the system must
have their BR Faston connectors wired together for proper
operation (except for between the DC and AC sections of an FPX
hybrid system).
Zone Outputs
(Out1 – Out8)
These are zone output terminal strips are removable and accept
wire sizes from AWG14 to AWG22. The terminals are labeled on
the PC board underneath the terminal strip.
Any locking device shall be configured for fail safe operation upon
occurrence of an alarm.
FAI LED
(D11) – Red
The FAI LED lights when FAI is active and an FAI input signal is
received from the FPO power supply.
Optional Output
Fuses (F1 – F8)
When using the PTC version of the CKM-F8P, the fuse will be
replaced with a soldered-in PTC.
Component Description
CKM-F8P Hardware Installation Manual
24-10707-147 Rev. C
4
WIRING INFORMATION
This section covers the following:
•Connecting the CKM-F8P Power Distribution Module
•Dual Voltage using Two Power Supplies with Eight Zones of FAI
Controllable Distribution
•Specifications
Connecting the CKM-F8P Power Distribution Module
Each of the B1, B2, BR, and FlexIO buses has two connectors. You can
use these connectors interchangeably.
For example, FlexIO from the power supply may be connected to either
of the CKM-F8P’s FlexIO connectors, the Main DC voltage source may
connect to either B1 terminal, and so on.
Figure 3: Connecting the CKM-F8P Board
WARNING: Risk of Electric Shock.
Remove all AC and battery power from the system before adding
or replacing a CKM-F8P module. Contact with components
carrying hazardous voltage can cause electric shock and may
result in severe personal injury or death.
!
CKM-F8P Hardware Installation Manual
24-10707-147 Rev. C
5
Single Voltage with Eight Zones of FAI Controllable Distribution
In this application, each zone output of the CKM-F8P may be set to
provide 24 V of continuous output, 24 V enabled for FAI, or 24 V
disabled for FAI. Because this is a single voltage system, only jumper
positions 1-3 are valid. FAI control on the CKM-F8P is achieved by
opening the NC contact on the power supply’s FAI input.
Figure 4: CKM-F8P Wiring: Single Voltage, Eight Zones
CKM-F8P Hardware Installation Manual
24-10707-147 Rev. C
6
Dual Voltage using Two Power Supplies with Eight Zones of FAI
Controllable Distribution
In this application, each zone output of the CKM-F8P may be set to
provide 24 V of continuous output, enable on FAI, or disable on FAI. FAI
control on the CKM-F8P is achieved by opening the NC contact on the
power supply’s FAI input.
Figure 5: CKM-F8P Wiring: Dual Voltage, Eight Zones
Tabla de contenidos
Otros manuales de Unidad de control de Johnson Controls
Johnson Controls
Johnson Controls MS-IOM3723 Manual de usuario
Johnson Controls
Johnson Controls H Series Manual de usuario
Johnson Controls
Johnson Controls IOM3711 Manual de usuario
Johnson Controls
Johnson Controls VG7000 Series Manual de usuario
Johnson Controls
Johnson Controls Penn A19K Series Manual de usuario
Johnson Controls
Johnson Controls Digital Vision Network 5000 Series Guía de inicio rápido
Johnson Controls
Johnson Controls Tyco CV-300B Manual de usuario
Johnson Controls
Johnson Controls Tyco DV-5a Series Manual de usuario
Johnson Controls
Johnson Controls VMA 1410 Guía de instalación
Johnson Controls
Johnson Controls TrueRH Series Guía
Johnson Controls
Johnson Controls CKM-MR51E Instrucciones de montaje
Johnson Controls
Johnson Controls GH-5000 Manual de usuario
Johnson Controls
Johnson Controls UL Listed GS-20 Series Manual de usuario
Johnson Controls
Johnson Controls M300CJ-R Manual de usuario
Johnson Controls
Johnson Controls Tyco TJPX0500003 Manual de usuario
Johnson Controls
Johnson Controls VG1000 Series Manual de usuario
Johnson Controls
Johnson Controls MS-NCM4510-2 Manual de usuario
Johnson Controls
Johnson Controls Y20EBD Series Manual de servicio
Johnson Controls
Johnson Controls tyco AMD-2 Manual de usuario
Johnson Controls
Johnson Controls LP-FXGPRSU-0 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
