Johnson Controls EM-3000 Series Manual de usuario
EM-3000 Series Meter Quickstart Guide QS - 1
Electronic Circuits
Ia Ia Ib Ib Ic Ic
(+) (-) (+) (-) (+) (-)
Va Vb Vc Vref L1 L2 PE
A B C N
A B C N
Ia
Ib
Ic
Power Supply Inputs
L2 is for Neutral
Electronic Circuits
Ia Ia Ib Ib Ic Ic
(+) (-) (+) (-) (+) (-)
Va Vb Vc Vn L1 L2 PE
A B C N
A B C N
Ia
Ib
Ic
Power Supply Inputs
WYE with PTs, 3
Phase, 4 Wire
Detail of JP2 Board and
LAN/485 Setting
WYE Direct, 3
Phase, 4 Wire
Front Cover
Support fitted
into its base
Power Supply
Inputs (Inputs
are unipolar)
L2 is for Neutral
Electronic Circuits
Ethernet, RJ45
Jack
Ia Ia Ib Ib Ic Ic
(+) (-) (+) (-) (+) (-)
Z K Y + - SH
Va Vb Vc Vn L1 L2 PE
RS485
KYZ Pulse
Output
Wireless Ethernet Connection
RS485 Output
(Do not put the
Voltage on these
terminals!)
Voltage
Inputs
Current
Inputs
Access Holes for
Wiring
JP2
WARNING! During normal operation of the meter
dangerous voltages flow through many parts of the meter,
including Terminals and any connected CTs and PTs, all I/O
modules and their circuits. All Primary and Secondary
circuits can, at times, produce lethal voltages and
currents. Avoid contact with any current-carrying surfaces.
Before performing ANY work on the EM-3000 Series
meter, make sure the meter is powered down and
ALL circuits are de-energized.
IMPORTANT! All wiring is done with the cover open, as shown
on the left. The front cover support fits into its base. Make sure
the support is up before closing the front cover.
Select wiring diagram to meet your application. See User Manual for additional wiring diagrams.
NOTE: Jumper 2 (JP2)
must be set for either
RS485 or Ethernet commu-
nication (see figures on the
left for location of JP2 and
settings). Put the jumper
on positions 2 and 3 for
LAN (Ethernet) communi-
cation, or on 1 and 2 for
RS485 communication.
EM-3000 Series Meter Quickstart Guide
Code No. LIT-12011870
Issued October 25, 2013
EM-3000 Series Meter Quickstart Guide QS - 2
Program Settings Using the Faceplate Buttons: (MENU, ENTER, DOWN ARROW, RIGHT
ARROW) See the figure below for the location of the faceplate buttons.
Access Configuration Mode:
1.Push the MENU button - you will see the display on the right; rSt will be
blinking.
2.Press the DOWN ARROW once. CFG (Configuration) moves to the
top of the display.
3.Press the ENTER button. You will see the Configuration menu, shown
on the right.
MAX
MIN
VOLTS L-N
AMPS
%LOAD
120%-
PRG
%THD
LM2
LM1
90%-
60%-
30%-
VOLTS L-N
W/VAR/PF
VA/H z
Wh
KILO
VARh
VAh
Wh Pulse
MEGA
A
B
C
MENU ENTER
IrDA 0000
0.659
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
Ia Ia Ib Ib Ic Ic
(+) (-) (+) (-) (+) (-)
Va Vb Vc Vref L1 L2 PE
A B C
A B C
Ia
Ic Electronic Circuits
Power Supply Inputs
DELTA with PTs, 3
Phase, 3 Wire
Electronic Circuits
Ia Ia Ib Ib Ic Ic
(+) (-) (+) (-) (+) (-)
Va Vb Vc Vref L1 L2 PE
A B C
A B C
Ia
Ic
Power Supply Inputs
DELTA Direct, 3
Phase, 3 Wire
EM-3000 Series Meter Quickstart Guide QS - 3
4.Press the DOWN ARROW and then press the ENTER button. You will see the CT
numerator setting screen (Ct-n). The current CT numerator is shown in the second
line. To change the setting, press the DOWN ARROW until the value you want is
displayed. Then press the RIGHT ARROW to move to the next digit. Repeat until
the setting is done.
5.Press the ENTER button to go to the CT denominator screen (CT-d). This setting is
display only - it can’t be changed.
6.Press the ENTER button to go to the CT Scaling setting screen (CT-S). The current
Scaling is shown in the second line. Press the DOWN ARROW to choose another
value. You can choose 1, 10, or 100.
7.Press the ENTER button to go to the PT numerator setting screen (Pt-n).The current
PT numerator is shown in the second line. To change the setting, press the DOWN
ARROW until the value you want is displayed. Then press the RIGHT ARROW to
move to the next digit. Repeat until the setting is done.
8.Press the ENTER button to go to the PT-denominator screen (Pt-d). The current
PT denominator is shown in the second line. To change the setting, press the DOWN
ARROW until the value you want is displayed. Then press the RIGHT ARROW to
move to the next digit. Repeat until the setting is done.
9.Press the ENTER button to go to the PT Scaling setting screen (PT-S). The current
Scaling is shown in the second line. Press the DOWN ARROW to choose another
value. You can choose 1, 10, 100, or 1000.
NOTE: See example CT and PT Settings on the next page.
10.Press the ENTER button to go to the Connection setting screen (Cnct). The current
setting is shown in the second line. Press the DOWN ARROW to choose another
value. You can choose 3 EL (element) WYE, 2 Ct del (Delta), or 2.5 EL WYE.
11.Press the ENTER button to go to the meter Address setting screen (Adr). The
meter’s current address is shown in the second line. To change the setting, press
the DOWN ARROW until the value you want is displayed. Then press the RIGHT
ARROW to move to the next digit. Repeat until the setting is done. Valid address-
es are from 001 through 247. If you are using the Ethernet option, do NOT
change anything on this screen.
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
EM-3000 Series Meter Quickstart Guide QS - 4
12.Press the ENTER button to go to the meter Baud Rate setting screen (bAUd). The
meter’s current Baud Rate is shown in the second line. Press the DOWN ARROW
to choose another Baud Rate. You can choose 9600 (choose this for RS485
connection), 19.2 (19200), 38.4 (38400) or 57.6 (57600). If you are using the
Ethernet option, do NOT change anything on this screen.
13.Press the ENTER button to go to the meter Protocol setting screen (Prot). The
meter’s current Protocol is shown in the second and third lines. Press the DOWN
ARROW to choose another communication Protocol. You can choose Mod rtU
(Modbus RTU; choose this for RS485 connection), Mod ASCI (Modbus ASCII), or
dnp (DNP 3.0). If you are using the Ethernet option, do NOT change
anything on this screen.
14.Press the ENTER button to go to the Scroll setting screen (SCrL). The current
setting is shown in the second line. Press the DOWN ARROW to choose another
setting. You can choose YES (the meter readings will scroll on the display) or no
(the meter readings will not scroll on the display).
15.Press the MENU button twice. You will see the Store Settings screen (Stor ALL?)
The default setting is YES. To save the settings you’ve made, press the ENTER
button. You will see the confirmation screen (Stor ALL done) and then the meter
resets.
NOTE: If you do not want to save your settings, press the RIGHT ARROW. YES
changes to no. Press the ENTER button.
Example CT Settings:
200/5 Amps: set the Ct-n value as 200, Ct-S value as 1.
800/5Amps: set the Ct-n value as 800, Ct-S value as 1.
2000/5 Amps: set the Ct-n value as 2000, Ct-S value as 1
10,000/5 Amps: set the Ct-n value as 1000, Ct-S value as 10.
Example PT Settings:
14400/120 Volts: set the Pt-n value as 1440, Pt-d value as 120, Pt-S value as 10.
138000/69 Volts: set the Pt-n value as 1380, Pt-d value as 69, Pt-S value as 100.
345000/115 Volts: set the Pt-n value as 3450, Pt-d value as 115, Pt-S value as 100.
345000/69 Volts: set the Pt-n value as 345, Pt-d value as 69, Pt-S value as 1000.
Refer to the EM-3000 Series Meter Installation and Operation Manual (LIT-12011874) for important
product application information. Also refer to the manual for additional wiring options and program-
ming information. The manual is on the enclosed CD.
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
A
B
C
-
-
-
MENU ENTER
Otros manuales para EM-3000 Series
1
Otros manuales de Unidad de control de Johnson Controls
Johnson Controls
Johnson Controls A19 Series Manual de usuario
Johnson Controls
Johnson Controls Tyco TJPX0500003 Manual de usuario
Johnson Controls
Johnson Controls A19ZBC Series Manual de servicio
Johnson Controls
Johnson Controls METASYS NU-XBN101-0 Manual de usuario
Johnson Controls
Johnson Controls MS-NCM4510-2 Manual de usuario
Johnson Controls
Johnson Controls VG8000V Series Manual de usuario
Johnson Controls
Johnson Controls 300 Series Manual de usuario
Johnson Controls
Johnson Controls S300 Series Instrucciones de montaje
Johnson Controls
Johnson Controls Tyco DV-5a Series Manual de usuario
Johnson Controls
Johnson Controls Tyco DV-5a Series Manual de usuario
Johnson Controls
Johnson Controls S1-TTSCC Manual de usuario
Johnson Controls
Johnson Controls Penn System 350 S350P Manual de usuario
Johnson Controls
Johnson Controls PENN P470 Manual
Johnson Controls
Johnson Controls F4-XPM Series Manual de usuario
Johnson Controls
Johnson Controls tyco AMD-2 Manual de usuario
Johnson Controls
Johnson Controls IOM3731 Manual de usuario
Johnson Controls
Johnson Controls VF Series Manual de usuario
Johnson Controls
Johnson Controls NIE39 Manual de usuario
Johnson Controls
Johnson Controls M300CJ Manual de usuario
Johnson Controls
Johnson Controls Tyco DV-5a Series Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
