Johnson Controls System 350 Manual de servicio

FANs 930, 125

Product/Technical Bulletin S350

Issue Date 0300

Part No. 24-7664-1, Rev. D www.johnsoncontrols.com

Code No. LIT-930080

System 350™

S350A Temperature, S351A Humidity,

and S352A Pressure Stage Modules

The S350A, S351A, and S352A Stage Modules are

intended to be used with System 350™ controls. Each

of these stage modules plugs into the respective

control module to add multiple-stage capability. These

stage modules have Single-Pole, Double-Throw

(SPDT) relay output with Light-Emitting Diode (LED)

indication.

As are all System 350 products, the stage modules are

housed in NEMA 1, high-impact thermoplastic

enclosures. The modular design provides easy,

plug-together connections for quick installation and

future expandability.

Figure 1: System 350 Stage Module

Features and Benefits

❑Modular Design Permits system to be configured to

equipment, with convenient, future expansion

made easy

❑Plug-together Connectors

and 35 mm DIN Rail

Mounting

Eliminates wiring between modules and

reduces installation costs

❑Selectable Mode of

Operation

Provides independent relay energization,

either above or below setpoint, for

cooling/heating (S350A),

dehumidification/humidification (S351A), or

direct acting/reverse acting (S352A)

❑Adjustable Differential Enables user to match the range of

temperature, humidity, or pressure stage

modules to specific application requirements

❑Adjustable Offset Allows multiple stage sequencing of 1-30F°

(0.5-17C°) (S350A), 2-30% RH (S351A), or

2-50 psi (S352AA-2)

2 S350A Temperature, S351A Humidity, and S352A Pressure Stage Modules Product/Technical Bulletin

Application

The S350A, S351A, and S352A Stage Modules

receive power, setpoint, and sensor input from the

respective System 350 control modules. When

connected, the individual modules act as a multistage

control system.

The maximum number of stages that can be used in a

system varies with the control module type

(temperature, humidity, or pressure) and stage module

design.

Refer to Table 1 or Table 2 to determine the maximum

number of stages that may be used with each control

module. When mixing stage module designs, always

use the lower number.

Note: When using an external transformer, the

Y65 Series or other 40 VA Class 2

transformers are recommended.

Table 1: Maximum Number of Add-on

Modules when Powered by a Y350R

Power Module

Stage

Module

Display

Module

Control

Module

No. Model

Numbers

No. Model

Number

A350A

A350B

A350E

S350As or S350Cs

with 1 S350P

S350As or S350Cs

with 2 S350Ps

1 D350

A350P 4

S350As or S350Cs

with 1 S350P

1 D350

A350R

A350S

S350As or S350Cs

with 1 S350P

S350As or S350Cs

with 2 S350Ps

2 D350s

W351A 5 S351As 1 D351

W351P 4 S351As 1 D351

P352AB 5 S352As 1 D352A

P352PN 4 S352As 1 D352A

Table 2: Maximum Number of Add-on

Modules when Powered by an External

Transformer

Stage

Module

Display

Module

Control

Module

No. Model

Numbers

No. Model

Number

A350A

A350B

A350E

S350As or S350Cs

with 1 S350P

S350As or S350Cs

with 2 S350Ps

1 D350

A350P 9

S350As or S350Cs

with 1 S350P

S350As or S350Cs

with 2 S350Ps

1 D350

A350R

A350S

S350As or S350Cs

with 1 S350P

S350As or S350Cs

with 2 S350Ps

2 D350s

W351A 9 S351As 1 D351

W351P 9 S351As 1 D351

P352AB 9 S352As 1 D352A

P352PN 9 S352As 1 D352A

Notes: This bulletin only refers to the S350A, S351A,

and S352A Stage Modules.

For information on the S350C refer to the

System 350TM S350C Temperature Slave

Stage Module Product/Technical Bulletin

(LIT-930084).

For information on the S350P refer to the

System 350TM S350P Proportional Plus

Integral Temperature Stage Module

Product/Technical Bulletin (LIT-930086).

For information on the D350, D351 and D352

refer to the System 350TM D350 Display

Modules Product/Technical Bulletin

(LIT-930070).

S350A Temperature, S351A Humidity, and S352A Pressure Stage Modules Product/Technical Bulletin 3

Operation

The S350A, S351A, and S352A Stage Modules

provide SPDT relay output. A front panel LED lights to

indicate when the relay is energized.

IMPORTANT: The System 350 Stage Modules

are intended to control

equipment under normal

operating conditions. Where

failure or malfunction of the

System 350 Stage Modules

could lead to an abnormal

operating condition that could

cause personal injury or damage

to the equipment or other

property, other devices (limit or

safety controls) or systems

(alarm or supervisory systems)

intended to warn of or protect

against failure or malfunction of

the System 350 Stage Modules

must be incorporated into and

maintained as part of the control

system.

Offset Adjustment

The offset adjustment determines the amount of offset

from the control module setpoint at which the stage

module relay de-energizes.

Differential Adjustment

Differential is defined as the difference in degrees,

% RH, or psi between energization and

de-energization of the stage module’s relay.

Operation Mode Selection

The S350A, S351A, and S352A utilize jumpers (at

jumper terminal J2) to select the operation mode. (See

Adjustments section and Figures 3, 4, and 5.)

With the jumpers positioned horizontally, the stage

module is set for Cooling (S350A), Dehumidification

(S351A), or Direct Acting (DA) (S352A) operation. In

this mode the relay and LED indicator de-energize

when the sensed temperature, humidity, or pressure

drops to the setpoint plus offset value.

With the jumpers positioned vertically, the stage

module is set for Heating (S350A), Humidification

(S351A), or Reverse Acting (RA) (S352A) operation. In

this mode, the relay and LED indicator de-energize

when the sensed temperature, humidity, or pressure

rises to the setpoint minus offset value.

Note: The S350A, S351A, and S352A Stage

Modules are configured with the jumpers in

the horizontal position at the factory.

Refer to Figures 6, 7, and 8 for examples of S350A,

S351A, and S352A applications.

Dimensions

1-3/16

(31)

2-3/8

(61)

7/16

(11)

1-1/2

(40)

1/8 (4)

DIN Rail

Mount

7/8 (22) Conduit

Hole

Mounting Slots

For No. 6 Screws

CONTROLS

JOHNSON

S350

5 (127)

2-15/16

(75)

(61)

2-3/8

7/8 (22)

Figure 2: System 350 Stage Module

Dimensions, in. (mm)

Mounting

Each System 350 Stage Module is housed in a

compact NEMA 1 plastic enclosure designed for

standard 35 mm DIN rail mounting. Four key-slot

mounting holes on the back of the control case are

provided for surface mounting. (See Figure 2.) The

modules are not position sensitive, but should be

mounted for convenient access to wiring and

adjustments.

Note: When mounting any System 350 module to

rigid conduit, attach the hub to the conduit

before securing the hub to the control

enclosure.

4 S350A Temperature, S351A Humidity, and S352A Pressure Stage Modules Product/Technical Bulletin

Adjustments

Refer to the following steps for adjusting stage module

settings. (See Figures 3, 4, and 5.)

WARNING: Risk of Electrical Shock.

Disconnect power supply to

avoid possible electrical shock or

equipment damage. More than

one disconnect may be required

to completely de-energize

equipment.

1. Ensure all power to system is off.

Each stage module may be receiving separate

power sources. Make sure all power sources to

each stage module are off.

2. Remove the stage module cover by loosening the

four captive cover screws.

3. Set the mode of operation by positioning the

jumpers (at jumper terminal J2) for Cooling,

Dehumidification, or Direct Acting mode. Position

the jumpers vertically for Heating, Humidification,

or Reverse Acting mode.

Note: The S350A, S351A, and S352A Stage

Modules are configured with the jumpers in

the horizontal position at the factory.

4. Adjust the differential using the potentiometer

marked DIFF to the desired setting (the difference

in degrees, % RH, or psi between energization

and de-energization of the stage module’s relay).

5. Adjust the offset using the potentiometer marked

OFFSET to the number of degrees, % RH, or psi

from the System 350 control’s setpoint at which

the stage relay de-energizes (above setpoint with

Cooling, Dehumidification, or Direct Acting mode

selected, or below setpoint with Heating,

Humidification, or Reverse Acting mode selected).

6. Replace the cover on the stage module and fasten

in place with screws.

7. Restore power to system.

Offset

Potentiometer

Module

Connector

Relay Energized

LED Indicator

Relay

Differential

Potentiometer

Module

Connector

Jumper

Position at J2

Heating

Cooling

N.C.

Relay

COM

Output

N.O.

Terminals

Cover Screw

1 of 4

Figure 3: Interior View of S350A Stage Module

Offset

Potentiometer

Module

Connector

Relay Energized

LED Indicator

Differential

Potentiometer

Module

Connector

Relay

Jumper

Position at J2

Humidification

Dehumidification

N.C.

Relay

COM

Output

N.O.

Terminals

Cover Screw

1 of 4

Figure 4: Interior View of S351A Stage Module

Offset

Potentiometer

Module

Connector

Relay Energized

LED Indicator

Differential

Potentiometer

Module

Connector

Relay

N.C.

Relay

COM

Output

N.O.

Terminals

Cover Screw

1 of 4

Jumper

Position at J2

Reverse

Acting

Direct

Acting

Figure 5: Interior View of S352A Stage Module

S350A Temperature, S351A Humidity, and S352A Pressure Stage Modules Product/Technical Bulletin 5

Setpoint

Temperature

Cooling Heating

A350

Stage 1

S350A

Stage 2

S350A

Stage 3

S350A

Stage 4

S350A

Stage 5

ON = Energized

OFF = De-energized

OFF

Differential

OFF

Higher

Temperature

Lower

Temperature

OFFSET

Differential

OFFSET

Differential

OFFSET

Figure 6: Example of a Heating/Cooling

Application Using One A350 and Four S350As

Higher

Humidity

Setpoint

Relative

Humidity

Dehumidify Humidify

W351

Stage 1

S351

Stage 2

S351

Stage 3

S351

Stage 4

Differential

OFF

Lower

Humidity

OFF

Differential

OFFSET

OFF

Differential

OFFSET

OFF

Differential

OFFSET

ON = Energized

OFF = De-energized

Figure 7: Example of a

Humidification/Dehumidification Application

Using One W351 and Three S351As

Setpoint

Pressure

Direct Reverse

P352AB

Stage 1

S352A

Stage 2

S352A

Stage 3

S352A

Stage 4

ON = Energized

OFF = De-energized

OFF

Differential

OFF

Higher

Pressure

Lower

Pressure

OFFSET

OFFSET OFFSET

Figure 8: Example of a Reverse Acting/Direct

Acting Application Using One P352AB

and Three S352As

Wiring

Refer to the following guidelines and wiring diagrams

for proper wiring and terminal designations (See

Figures 9, 10, and 11.)

Note: For information on connecting to an external

transformer refer to the applicable control

bulletin.

WARNING: Risk of Electrical Shock.

Disconnect power to avoid

possible electrical shock or

equipment damage. More than

one disconnect may be required

to completely de-energize

equipment.

IMPORTANT: Make all wiring connections in

accordance with the National

Electrical Code and all local

regulations. Use copper

conductors only. Do not exceed

the control’s electrical ratings.

The stage modules plug into the control and other

add-on modules via 5-pin connectors located on either

side of each module. Wiring is made at the Normally

Open (N.O.)/Normally Closed (N.C.) relay terminal

strip. (See Figures 3, 4, and 5.)

6 S350A Temperature, S351A Humidity, and S352A Pressure Stage Modules Product/Technical Bulletin

Y350R S350A D350

S350A S350A

Isolate and tape. (Do not ground

this end of cable shield.)

Load

Sensor

Shield (Connect

only to COM on A350)

120 VAC

A350

Wire

Terminal

Block

24V

COM

VDC

SEN

SEN COM

Figure 9: Typical Multistage Temperature Control System Using 120 VAC Power Supply

W351 Y350R S351A D351S351A S351A

COM

Load Load Load Load

Transmitter

120 VAC

VDC

Wire

Terminal

Block

24V

COM

VDC

SEN

Isolate and tape. (Do not ground

this end of cable shield.)

Shield (Connect

only to COM on W351)

SEN

Figure 10: Typical Multistage Humidity Control System Using 120 VAC Power Supply

P352AB Y350R S352A S352A D352AS352A

Load Load Load Load

P399 Transducer

Wiring Harness

SEN VDC COM

120 VAC

Shield (Connect

only to COM on P352AB)

Isolate and tape. (Do not ground

this end of cable shield.)

Wire

Terminal

Block

24V

COM

VDC

SEN

Figure 11: Typical Multistage Pressure Control System Using 120 VAC Power Supply

S350A Temperature, S351A Humidity, and S352A Pressure Stage Modules Product/Technical Bulletin 7

Checkout Procedure

Before applying power, make sure installation and

wiring connections are according to job specifications.

After necessary adjustments and electrical

connections have been made, put the system in

operation and observe at least three complete

operating cycles before leaving the installation.

Troubleshooting

If the control system does not function properly, first

verify that the control, power, and display modules are

all operating correctly (refer to the respective

literature). Then inspect the stage modules for proper

operation.

Check that the proper operating mode

(Cooling/Heating, Dehumidification/Humidification, or

Direct Acting/Reverse Acting) has been selected on

each stage module. (See Adjustments section and

Figures 3, 4, and 5.) Then perform the following

procedures to determine the problem.

1. Verify the system has power.

2. Note the offset and differential settings on the

stage module.

3. Turn the setpoint dial on the control module to

minimum.

4. Increase the setpoint by slowly adjusting the

setpoint dial until the stage relay LEDs turn On

and Off as shown in Tables 3, 4, or 5.

Table 3: S350A Relay Troubleshooting

Operation

Mode

LED N.O.

Relay

Status

Setpoint Dial

Setting

Cooling On Closed (Ts)* -offset

-differential

Cooling Off Open (Ts) –offset

Heating On Closed (Ts) +offset

+differential

Heating Off Open (Ts) +offset

*(Ts) = sensed temperature

Table 4: S351A Relay Troubleshooting

Operation

Mode

LED N.O.

Relay

Status

Setpoint Dial

Setting

Dehumidify On Closed (RHT)* -offset

-differential

Dehumidify Off Open (RHT) -offset

Humidify On Closed (RHT) +offset

+differential

Humidify Off Open (RHT) +offset

*(RHT) = actual relative humidity at transducer

Table 5: S352A Relay Troubleshooting

Operation

Mode

LED N.O.

Relay

Status

Setpoint Dial

Setting

Direct On Closed (psiT)*-offset -

differential

Direct Off Open (psiT) - offset

Reverse On Closed (psiT) +offset +

differential

Reverse Off Open (psiT) +offset

*(psiT) = actual pressure at transducer

5. If the relays do not perform as indicated in

Tables 3, 4, or 5, adjust the stage module’s

differential and offset potentiometers to minimum

and repeat Steps 1 through 3.

6. If the relays still do not turn on and off, replace the

defective stage modules.

Note: There is the unlikely possibility that a defect in

one stage module could cause defective

symptoms in all modules. Plug each stage into

the control individually and check the

performance of each as explained above.

Repairs and Replacement

Do not make field repairs or perform calibration.

Sensors and replacement controls are available

through your local Johnson Controls representative.

8 S350A Temperature, S351A Humidity, and S352A Pressure Stage Modules Product/Technical Bulletin

Ordering Information

Table 6: Ordering Information

Item Product Code

Number

Description

S350AA-1C Temperature Stage Module with Fahrenheit Scale

S350A Temperature Stage

Module S350AB-1C Temperature Stage Module with Celsius Scale

S351A Humidity Stage Module S351AA-1C Humidity Stage Module with percent RH Scale

S352A Pressure Stage Module S352AA-2C Pressure Stage Module with psi Scale

Specifications

Product S350AA: Temperature Stage Module with Fahrenheit Scale

S350AB: Temperature Stage Module with Celsius Scale

S351AA: Humidity Stage Module with Percent RH Scale

S352AA-2: Pressure Stage Module with psi Scale

Input Voltage S350AA: Provided by the A350

S351AB: Provided by the W351

S352AA-2: Provided by the P352AB

Power Consumption 1.0 VA maximun

Output Relay Electrical

Ratings

SPDT Enclosed Relays

10 Ampere Non-inductive, 125 VA Pilot Duty, 24/240 VAC

1/2 hp 120/240 VAC

Differential Adjustment

Range

S350AA: 1 to 30F°

S350AB: 0.5 to 17C°

S351AA: 2 to 10% RH

S352AA-2: 2 to 50 psi

Offset Range S350AA: 1 to 30F°

S350AB: 0.6 to 16.7C°

S351AA: 2 to 30% RH

S352AA-2: 2 to 50 psi

Ambient Temperature Operating: -30 to 150°F (-34 to 66°C)

Shipping: -40 to 185°F (-40 to 85°C)

Ambient Humidity 0 to 95% RH (Non-condensing)

Material Case, Cover: NEMA 1 High Impact Thermoplastic

Mounting Wall or DIN Rail

Agency Listing UL Listed, CCN XAPX, File E27734

UL Listed for Canada, CCN XAPX7, File E27734

The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these

specifications, consult Johnson Controls/Penn Application Engineering at (414) 274-5535. Johnson Controls, Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

Controls Group

507 E. Michigan Street

P.O. Box 423 Printed in U.S.A.

Milwaukee, WI 53201 www.johnsoncontrols.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Johnson Controls

Johnson Controls

Johnson Controls V46SA Series Manual de usuario

Johnson Controls

Johnson Controls MS-IOM3723 Manual de usuario

Johnson Controls

Johnson Controls F4-XPM Series Manual de usuario

Johnson Controls

Johnson Controls S1-TTSCC Manual de usuario

Johnson Controls

Johnson Controls Tyco DV-5a Series Manual de usuario

Johnson Controls

Johnson Controls M4-XPM Manual de usuario

Johnson Controls

Johnson Controls VG1000 Series Manual de usuario

Johnson Controls

Johnson Controls Penn System 450 Series Manual de usuario

Johnson Controls

Johnson Controls VMA 1410 Guía de instalación

Johnson Controls

Johnson Controls UL Listed GS-20 Series Manual de usuario

Johnson Controls

Johnson Controls tyco AMD-2 Manual de usuario

Johnson Controls

Johnson Controls A19 Series Manual de usuario

Johnson Controls

Johnson Controls GM 20 Series Manual de usuario

Johnson Controls

Johnson Controls PENN P470 Manual

Johnson Controls

Johnson Controls Tyco PRV-1A Manual de usuario

Johnson Controls

Johnson Controls VP101DBB Manual de usuario

Johnson Controls

Johnson Controls Tyco DV-5a Series Manual de usuario

Johnson Controls

Johnson Controls GS Series Manual de usuario

Johnson Controls

Johnson Controls EM-3000 Series Manual de usuario

Johnson Controls

Johnson Controls IOM3723 Manual de usuario

Johnson Controls

Johnson Controls Digital Vision Network 5000 Series Guía de inicio rápido

Johnson Controls

Johnson Controls Mercury P2000 CKM-MR16IN Manual

Johnson Controls

Johnson Controls System 450 Series Manual de usuario

Johnson Controls

Johnson Controls MS-NCM4510-2 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario