Jbc PH B Series Manual de usuario

www.jbctools.com

PH-B

INFRARED PREHEATER

DESCRIPTION

PH-B / INFRARED PREHEATER

PH-2B / PH-1B / PH-9B

Infrared Preheater

Back heating zone

Fixing bracket

for PH321 Support

All zones

Front heating zone

Heater unit Console

0009401

Power Cord

ThermoCouple

Main Switch

Power cord

socket

Console

socket

Pedal

socket

Fuse

Increase

& move up

Decrease

& move down

Select &

confirm

Friendly display control

Heat

Start & stop

button

INSTALLATION

console

connection pedal connection

Heat

Start & stop pedal

Auxiliar

Thermocouple Type K

Control

Thermocouple Type K

USB

connector to PC:

- Update Preheater software

P-005 Pedal

ConsoleP edal

Times

Pre-Set

P1 Low

Pre-Set

P2 Medium

Pre-Set

P3 High

t1 30 sg 40 sg 60sg

t2 15 sg 25 sg 40sg

t3 4 min 4 min 4 min

MAIN MENU

PRE-SET PROFILES

Basic Mode

The unit will keep the selected temperature at the point where the Control TC is placed. The maximum

working time and the maximum ramp-up rate are set in the station settings menu. In the station settings

you can also select the maximum temperature available and set a unique temperature.

Power Mode

The unit works with the power selected. If you wish to see the actual temperature, plug in the Control TC.

Builder Profile

Build your custom profile step by step, test it and check it as many times as you wish. Once defined, save

it in the profile memory.

Pre-Set Profiles

Run a pre-set profile. The profiles 1 (low), 2 (medium) and 3 (high) are pre-set for a standard rework process.

Custom Profiles

Run a saved custom profile. The custom profiles must be previously set by means of the builder profile or

by using the options of the Profile Settings Menu: Edit, Copy and Delete.

The unit incorporates 3 default profiles which are appropriate for most common jobs on FR4 bilayer

substrates, multilayer and thick multilayer respectively.

Profiles are appropriate if you work with PH321 support at its lowest working position (21mm *) and with

the PCB focused on the PH. The Control TC must be placed with Kapton on the top side of the board,

near the component to be repaired.

Control TC

21mm*

PCB

PH321 Support PH

T1sg T2sg

P2 P3

T3sg

100ºC

80ºC

Tamb

MAIN WARNING

RECOMENDED GUIDELINES

RELATIVE PROFILE

It is possible to run all profiles with the Control TC plugged or unplugged.

When the Control TC is plugged, all the working modes follow the target temperatures of the selected

profile.

Once a profile has been run for the first time, it is already available in the “relative profile” mode. This

means you can run this profile without plugging the Control TC. If you place the board on the PreHeater

as the same way than you run the profile for the first time with the TC, the board will be heated identically.

To make it easier, the PH321 support has a numbered ruler and fitting parts.

Each time a profile runs completely with the plugged TC, the Relative Profile is updated.

It is possible to test a Relative profile by using the Test Relative profile within the Profile Settings menu.

MAXIMUM RAMP-UP EXCEED

The maximum ramp-up rate is set in the Station Setting Menu. The unit shows this warning if anytime

you exceed this gradient.

NO RELATIVE PROFILE. CONNECT TC

The profile should be run completely at least one time in order to be saved in the relative profile.

SECURITY TERMOCOUPLE EXCEEDED

The unit is equipped with an auxiliary TC. It is possible to set a temperature target for this TC in the Station

Settings Menu. The unit stops when the auxiliary TC reaches the target set.

INVALID PROGRAM. Error > 10ºC

This is displayed when the actual temperature differs from the setpoint by more than 10ºC for 20s.

The unit incorporates 3 default profiles which can be appropriate for most common jobs about FR4 bila-

yer substrates, multilayer and thick multilayer respectively.

1. Place the Control TC as near as possible of the component to work with.

2. If there is any sensitive component, use the Auxiliary Thermocouple as protection.

3. For repetitive jobs, you can work without TC. Once you set the appropriate profile by using the

Thermocouple, you can use the Relative Profile for the following PCBs to repair. The heating will be

always the same as long as you work with the same board on the same place and position.

4. Do not exceed the allowable heat cycles for a board or component.

5. Do not recommend to exceed ramp-up rates of more than 3-4 °C /sec

Original Pin 0105

WARRANTY

JBC’s 2 year warranty covers this equipment against all ma-

nufacturing defects, including the replacement of defective

parts and labour.

Warranty does not cover product wear due to use or mis-use.

In order for the warranty to be valid, equipment must be returned,

postage paid, to the dealer where it was purchased enclosing

this form duly filled in.

SERIAL Nº

DEALER’S STAMP

DATE OF PURCHASE

0013384-1213

TECHNICAL SPECIFICATIONS

- Maximum Power: 600VA

- Heated Area: 75 or 130 x 135mm (2 zones)

- Heating Power: 50 to 500 watt

- Adjustable Heating Rate: 1 to 10 K/s

- Maximum work time: 60 min

- Temperature Rate, from 50 to 250°C (120 to 480ºF)

- Temperature Measurement, K ThermoCouple

- 3 Pre-set profiles

- Custom Profiles, up to 17 (10 steps for each profile)

- PH-1B 120V. Input 120V 50/60Hz

- PH-2B 230V. Input 230V 50/60Hz

- PH-9B 100V. Input 100V 50/60Hz

- Fuses: Overload protection: 230V 4 A T - 120V / 100V 8 A T

- Total weight of unit: 2,8 kg

- Complies with CE standards on electrical safety, electromagnetic compatibility and ESD

protected housing “skin effect”.

- RoHS compliant.

This product should not be

thrown in the garbage.

www.jbctools.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario

multicomp pro

multicomp pro MP740893 Manual de usuario

jbc PH B Series Manual de usuario

Manuales populares de Pistola de soldar de otras marcas