Jbc PHSK-B Manual de usuario

日本語 33

Deutsch 23

Español 13

English 3

Page

IR Preheater system

Ref. PHSK-B

www.jbctools.com

中文 43

222

Ref. CLMB-A

Packing List

The following items should be included:

Heater Unit

Heater Unit ................................................1 unit

Console. .....................................................1 unit

PCB Support ............................................1 unit

Power Cord ...............................................1 unit

Kapton Tape .............................................1 unit

Thermocouple ..........................................1 unit

Console

Power Cord

Ref. 0009417 (100V/120V)

Ref. 0009401 (230V)

Thermocouple

Ref. PH218

Kapton Tape

Ref. PH217

PCB Support

Ref. PH321

Manual

ww w. jbc to ols .c om

Ref. PHSK-B

IR Preheater system

IR Preheater

Ref. PH-1B (120V)

Ref. PH-2B (230V)

Ref. PH-9B (100V)

www.jbctools.com

444

Features

Console socket

connection Pedal socket connection (optional)

Heating Area

Mains

input

Mains

switch

Fixing brackets

for PH321 Support

Heater Unit

Console Control Unit

Auxiliary Thermocouple (Type K)

Input

Thermocouple

(Type K)

USB-B connector to PC:

- Update the Control Unit

software

Zone B

Zone A

555

PCB Support

For fixing

irregular

shaped

PCBs to the

support.

For fixing identical PCBs

in the same position.

Slot Clamps

Height Adjustment

The PCB Support allows adjusting for 3 heights between the board and the Heating Area.

For PCBs of 0.8-2.4mm thick.

For PCBs of 2.4-6mm thick.

· Low level

· High level

· Medium level

For PCBs over 6mm thick.

28mm

50mm

70mm

www.jbctools.com

Profiles by Temperature

Why Infrared? The most efficient technology for PCB preheating

Operation

The usual way to run a profile is using the Thermocouple (TC) connected to the Control Input of the

console. JBC offers 3 predefined profiles (JBCset) and 20 profiles ready for you to personalize.

JBCset profiles

There are 3 profiles predefined by JBC: A, B and C. The difference between them is the number

of steps: 2, 3 or 4. The thicker your PCB is and the more layers it contains, the more steps are

needed to obtain a gradual warming.

These profiles are not modifiable but they can be used as a template to create your own profiles.

JBCset A

2 steps

JBCset B

3 steps

JBCset C

4 steps

This is the most advanced, efficient and cost-effective method to preheat PCBs in any soldering

job or rework job. The low thermal mass of the infrared element gives outstanding control of the

heat output and the process temperature. This technology provides fast response, high heating

rates and uniform heating that ensure the best results.

For repetitive jobs we recommend running profiles without the Thermocouple (TC). Once

any profile has been run to the end, the system has all the process data which you can save.

Once it is saved, you can run this profile without connecting the Thermocouple (TC). The

heating process will the same as long as the same working conditions are respected.

User profiles

You can create your own profiles from the JBCset profiles. On the work screen of the profile,

press the Enter button and choose the option Edit profile.

Power or Temperature Modes

The unit works at the selected power or temperature during the defined time. These parameters

can be modified from the work screen by pressing the Enter button and the Edit parameters menu.

To see the current temperature you must plug the Thermocouple (TC) into the Control connector.

PCB

reference

specifications:

FR4 1,6mm thick

and 2 layers.

FR4 2,2mm thick

and 6 layers.

FR4 1,6mm thick

and 6 layers.

Profiles set using the low position of the PH321 PCB Support (28 mm in height between the PCB and the heating area).

Recommended Guidelines

1. Place the Thermocouple (TC) as near as possible to the component being worked on.

2. If there are any sensitive components, use the Auxiliary Thermocouple as protection.

You can select the protection temperature in Station settings. If the selected temperature is rea-

ched, the Heater Unit will stop the process and a warning message will be shown.

3. IPC* does not recommend exceeding ramp-up rates over 3 - 4 °C / sec (5 - 7 °F / sec) so as to

reduce the risk of thermal stress on the PCB.

* IPC was founded in the U.S. in 1957 as the Institute for Printed Circuits.

Fix the TC with Kapton Tape

Auxiliary Thermocouple (TC)

www.jbctools.com

Display Control

www.jbctools.com

Safety

It is imperative to follow safety guidelines to protect health and prevent electric

shock, injury, fire or explosions.

- Do not use the units for any purpose other than PCB preheating. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- The temperature of accessible surfaces may remain high after the unit is turned off. Handle with care.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given

adequatesupervision or instruction concerning use ofthe appliance and understand thehazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

Otros manuales para PHSK-B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario

multicomp pro

multicomp pro MP740893 Manual de usuario

jbc PHSK-B Manual de usuario

Manuales populares de Pistola de soldar de otras marcas