Jbc HDT-SD Manual de usuario

Este manual sirve para los siguientes modelos

2

Tabla de contenidos

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario

multicomp pro

multicomp pro MP740893 Manual de usuario

INSTRUCTION MANUAL

Stands for HD

Handles and Tweezers

Ref. HD-SE / HDT-SD

www.jbctools.com

INSTRUCTION MANUAL

2

Packing List

The following items should be included in each stand:

Manual...............................................1 unit

Ref: 0021657

Ref. HD-SE HDT-SE

Stand ..................................................1 unit

Ref. HD-SE

Stands for HD

Handles and Tweezers

Stand ..................................................1 unit

Ref. HDT-SE

Includes: Cable flange (Ref.0010546)

Stand cable 1m ............................... 2 units

R ef. 0 0112 83

www.jbctools.com

Features

3

To HDE Control Unit

The HDT-SE Stand requires

two Heavy Duty stations (HDE)

to manage the C470 cartridges

individually thereby optimizing

their thermal performance.

Stand

Ref. HDT-SE

To HD470

Thermal Tweezers

To T470 Handles

Stand

Ref. HD-SE

To HDE Control Unit

using the Stand Cable

To HDE Control Unit

www.jbctools.com

4

Cartridge Extractor

1. Remove the cartridges using the extractor. Follow the ”Placing cartridges” guidelines.

Make sure the cartridges have cooled down before replacing them.

2

1

Handpiece screw

Follow these steps once you have loosened the handpiece screw.

2. You can also use the extractor to insert the cartridges and align them.

Tighten the screws for a correct use.

Handpiece screw

5

Assembly of Cable Collector and Adjustable Tool Holder

Assembly for HD-SE.

Assembly for HDT-SE.

Cable holder

Ref. 0010546

www.jbctools.com

6

Safety

- Do not use the stands for any purpose other than soldering or rework.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use in order to activate the sleep mode.

The soldering tip, the metal part of the tool and the stand may still be hot even when the station

is turned off. Handle with care, including when adjusting the stand position.

- Avoid the contact of flux with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

Accessories

Stand extension cable

Ref. A1286

Length: 1.5m

Stand cable

Ref. 0011283

7

Clean periodically

Maintenance

Before carrying out maintenance or storage,

always unplug the stand from the station and

the tool.

- Use a damp cloth to clean the stand.

Alcohol can be used only when cleaning

the metal parts.

- Check periodically that the metal parts of

the tool/stand are clean so that the station

can check the tool’s status.

- Periodically check all cables and tube

connections.

- Replace any defective or damaged parts.

Use original JBC spare parts only.

- Repairs should only be performed by a

JBC authorized technical service.

www.jbctools.com

0021657-0518

HD-SE

- Includes Sleep mode

- Net Weight 1.300 kg (2.87 lb)

- Package Weight 1.558 kg (3.43 lb)

- Package Dimensions 342 x 155 x 120 mm (13.46 x 6.10 x 4.72 in)

HDT-SE

- Includes Sleep mode

- Net Weight 1.3411 kg (3.11 lb)

- Package Weight 1.689 kg (3.72 lb)

- Package Dimensions 342 x 155 x 120 mm (13.46 x 6.10 x 4.72 in)

Complies with CE standards

ESD protected

Specifications

This product should not be thrown in the garbage.

In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life

must be collected and returned to an authorized recycling facility.

Manual in other languages available on our website

Warranty

JBC’s two-year warranty covers this equipment

against all manufacturing defects, including the

replacement of defective parts and labour. Warranty

does not cover product wear or misuse. In order for

the warranty to be valid, equipment must be returned,

postage paid, to the dealer where it was purchased.

Register your warranty within 30 days of purchase

in www.jbctools.com/productregistration

www.jbctools.com