Jbc HDE-1B Manual de usuario

HDE-B Robot station

Ref. HDRE-B

English 2

Page

Deutsch 21

Español 11

中文 31

www.jbctools.com

Packing List

The following items should be included:

Heavy Duty Control Unit ......................... 1 unit

Ref. HDE-1B (120V)

HDE-2B (230V)

HDE-9B (100V)

HD Purpose Handle

with 3m cable ............................................ 1 unit

Ref. T470-SA

HDE-B Robot station

Ref. HDRE-B

Manual ............................ 1 unit

Ref. 0016282

Power cord .................... 1 unit

Ref. 0010569 (230V)

0013671 (100/120V)

Converter ....................... 1 unit

Ref. CHB-A

www.jbcto o ls.c o m

Manage and monitor the station using a Robotic system.

1. Connect the tool to the station port by means of the CHB-A Converter.

2. Connect your Robot system to the Robot connector (RJ12) of the station.

DB9-RJ12 Adapter available only if necessary (Ref: 0013772).

3. Enable the Robot option in the station settings and the notification will be displayed

4. Set your Robot’s commands according to the Robot Communication Protocol,

available on the website www.jbctools.com/jbcsoftware-menu-115.html.

Working with Robots

Features

USB-A

connector

Tilt the display for

easy reading

2.8” Color TFT screen

Control UnitRobot Converter

Ref. CHB-A

RS-232

connection

www.jbctools.com

380ºC

Port

Power

45%

Temp. Levels

T470

250 380 400

17:14

USB flash drive is connected.

Station is controlled by a PC.

Station is controlled by a robot.

Station software update.

Press INFO to start the process.

Warning.

Press INFO for failure description.

Error. Press INFO for failure description,

the type of error and how to proceed.

System notifications (Status Bar)Menu Options

Station

Information

Power

indicator

Tool

in use

Work Screen

Status bar

The HDE offers an intuitive user interface which provides quick access to station parameters.

Change

port

Displayed if

temperature

levels are

activated

Station Tools Counters

ResetGraphicsPeripherals

Press INFO for each parameter description.

Port 1 - T245

450

400

350

300

250

150

100

200

Power Temp

17:14

By pressing Graphics in the main MENU, temperature and power ﬁgures in real

time are displayed for each port. This helps you decide which tip to use to obtain

the best quality solder joints.

Process analysis

Export graphics

Insert a USB ﬂash drive into the USB-A

connector to save your soldering process in

csv format.

Graphics

Temperature

Power (%)

See other

port graphic

www.jbctools.com

Soldering Net

Remotely manage and monitor as many stations as your Windows PC can handle.

any JBC station

JBC

Manager

software

USB Hub

Functions:

- Set all the station parameters from your PC.

- Organize groups of stations and set all their

parameters at the same time.

- Store specific configurations for later uses.

- Analyze the soldering graphics of the

stations on your PC and export them.

1. Download the JBC Manager software and the user manual from www.jbctools.com/manager.html

2. Connect the stations via USB-B connector and the PC will automatically detect them.

3. The notification will be displayed on the station.

Update the station software

1. Download the JBC Update File from

www.jbctools.com/software.html and save

it on a USB flash drive. Preferably one with no

other files.

JBC

Update File

2. Insert the USB flash drive to the station.

The icon is diplayed while updating.

Clean periodically

Maintenance

Before carrying out maintenance or storage, always allow the equipment to cool.

- Clean the station screen with a glass cleaner

or a damp cloth.

1. Pull off the fuse holder and remove the

fuse. If necessary use a tool to lever it off.

2. Press the new fuse into the fuse holder

and replace it in the station.

Fuse holder

Fuse

- Replace any defective or damaged pieces. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

- Use a damp cloth to clean the casing and the

tool. Alcohol can only be used to clean the

metal parts.

- Periodically check that the metal parts of the

tool and stand are clean so that the station

can detect the tool status.

- Maintain tip surface clean and tinned prior to

storage in order to avoid tip oxidation. Rusty

and dirty surfaces reduce heat transfer to the

solder joint.

- Periodically check all cables and tubes.

- Replace a blown fuse as follows:

www.jbctools.com

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The soldering tip, the metal part of the tool and the stand may still be hot even when the station

is turned off.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

Safety

HDRE-1B 120V 50/60Hz. Input fuse: 4A. Output: 47V. Control Unit model: HDE-1B

HDRE-2B 230V 50/60Hz. Input fuse: 2A. Output: 47V. Control Unit model: HDE-1B

HDRE-9B 100V 50/60Hz. Input fuse: 4A. Output: 47V. Control Unit model: HDE-1B

- Weight: 3.9 Kg (8.6 lb)

- Dimensions: 145 x 120 x 225 mm

- Output Peak Power: 250W

- Temperature Range: 90-500 ºC (190-932 ºF)

- Idle Temp. Stability (still air) ±1.5 ºC (±3 ºF)

- Tip to ground resistance: <2 ohms

- Tip to ground voltage: <2mV RMS

- Ambient Operating Temperature: 10-40 ºC (50-104 ºF)

- USB-A / USB-B / Peripherals connectors

- RJ12 connector for Robot

Complies with CE standards

ESD protected housing “skin effect”

Specifications

www.jbctools.com

Otros manuales para HDE-1B

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario

multicomp pro

multicomp pro MP740893 Manual de usuario

jbc HDE-1B Manual de usuario

Manuales populares de Pistola de soldar de otras marcas