Jbc DR Series Manual de usuario

Espa ñ o l 11

Stands

English 3

Page

INSTRUCTION MANUAL

www.jbctools.com

Stands

Packing List

The following items should be included:

Stand ............................................................ 1 unit

See references on the next page

Cable Holder

(Only in DR & DS stands) ........................... 1 unit

Ref. 0010154

Stand Cable ............................................... 1 unit

R ef. 0 0112 83

Manual .......................................................... 1 unit

Ref. 0012507

www.jbctools.com

For T210 & T245

Handles

Ref. AD-SD

For PA120-A

Micro Tweezers

Ref. PA-SD

For DS360-A

Micro Desoldering Iron

Ref. DS-SD

For HT420-A

Thermal Tweezers

Ref. HT-SD

For DR560-A

Desoldering Iron

Ref. DR-SD

For T245-NA

Nitrogen Handle

Ref. DN-SD

For AP130-A

Solder Feed Iron

Ref. AP-SD

All these stands can be connected to the following JBC Control units: DI, DDE, DME.

For T210-NA, T245-NA

and T470-NA

Nitrogen Handle

Ref. DN-SE

Quick Tip Changer

Features

1. Removing 2. Inserting 3. Fixing

Place the cartridge in the

extractor and pull the handle

to remove it.

Place the handle on top

of the new cartridge and

press down.

Use the holes to fix the

cartridge* as follows:

A. For straight C210.

B. For curved C210.

C. For curved C245.

D. For straight C245.

Save time and change cartridges safely without switching the station off.

*Important

It is essential to

insert the cartridge

as far as the mark

for a proper

connection. Mark

Tool

Control Unit

Stand

www.jbctools.com

Assembly for AD, DN, AP, PA, HT stands.

Assembly for DR and DS stands.

Assembly of cable collector and adjustable tool holder

Cable holder

Ref. 0010154

HT-SD tool placement for large tips

Accessories

Suction extension tube kit

Ref. A1287

Length: 1.5m

Stand extension cable

Ref. A1286

Length: 1.5mStand Cable

Ref. 0011283

www.jbctools.com

Clean periodically

Maintenance

Before carrying out maintenance or storage,

always unplug the stand from the station and

the tool.

- Use a damp cloth to clean the stand.

Alcohol can be used only when cleaning

the metal parts.

- Check periodically that the metal parts of

the tool/stand are clean so that the station

can check the tool’s status.

- Periodically check all cables and tube

connections.

- Replace any defective or damaged parts.

Use original JBC spare parts only.

- Repairs should only be performed by a

JBC authorized technical service.

Safety

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use in order to activate the sleep mode.

The soldering tip, the metal part of the tool and the stand may still be hot even when the station

is turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Avoid the contact of flux with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

www.jbctools.com

AD-SD

- Includes: 3 cartridges extractor magazine for C210 or C245

Quick cartridges change

Sleep mode

- Weight: 1,369 kg (3.01 lb)

AP-SD

- Includes: Sleep mode

- Weight: 1,301 kg (2.86 lb)

DN-SE

- Includes: Sleep mode

- Weight: 1,327 kg (2.92 lb)

PA-SD

- Includes: Sleep mode

- Weight: 1,304 kg (2.87 lb)

HT-SD

- Includes: Sleep mode

- Weight: 1,411 kg (3 .11 l b)

DS-SD

- Includes: Sleep mode

- Weight: 1,260 kg (2.77 lb)

DR-SD

- Includes: Sleep mode

- Weight: 1,410 kg (3.11 lb)

Complies with CE standards

ESD protected

Specifications

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Manuales populares de Pistola de soldar de otras marcas

Bakon

Bakon 3200 Manual de usuario

Proxxon

Proxxon Gaslotset MGS Manual de usuario

HAKO

HAKO FX-8804 Manual de usuario

SATA

SATA 02002A Manual de usuario

Velleman

Velleman HRJA151 Manual de usuario

Weller

Weller WSM 1 Manual de usuario

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instrucciones de montaje

ersa

ersa i-CON 1V Manual de usuario

Hakko Electronics

Hakko Electronics FX-100 Manual de usuario

Weller

Weller WAD 101 Manual de usuario

Weller

Weller WXD 2 Manual de usuario

AlienTek

AlienTek T100 Manual de usuario

Atten

Atten ATETOOL AT-689A Manual de usuario

Surtek

Surtek 112554 Dimensiones y guía de instalación

Parkside

Parkside PLBS 30 A1 Manual de usuario

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manual de usuario

Weller

Weller WX1 Manual de usuario

multicomp pro

multicomp pro MP740893 Manual de usuario

jbc DR Series Manual de usuario

Manuales populares de Pistola de soldar de otras marcas